2A22Q-DH005Wireless Battery Camera

Battery Camera Quick User Manual - Battery camera does not support AP hotspot mode. - This camera does not support 5GHz WiFi, please connect via 2.4GHz WiFi. - Check if DHCP is enabled on the router. Before starting setup DC 5V DC 5V DC 5V ON/OFF RESET Micro SD - The low-power battery camera is equipped with 2PCS 18650 batteries by default, please charge the batteries before using the camera for the first time. 1.Products Introduction Step1. SriHome App Installation 2. Device connection Method 1: Search for “SriHome” on Google Play or iOS App Store. ON/OFF RESET TF Card Slot TF Card Slot ON/OFF RESET ON 5VDC OFF -1- -2- Step2. Registration & Login on SriHome App Step3. Power on the Camera Method 2: Scan the QR code to download “SriHome” App. The camera will emit a continuous “beep” after 30 seconds. Note: If there is no “beep” sound, keep holding the “RESET” button for 5 seconds until you hear a long “Beep” Turn the power switch to ON, and the camera will turn on. Step4. Add the camera to the SriHome App When you hear the continuous “beep”, follow the instructions of the SriHome App to add the device, as in the figure: RESET DC 5V ON/OFF RESET Micro SD ON/OFF ON/OFF ON 5VDC OFF AndroidiOS (Please charge the batteries before using the camera for the first time) Notice: 1. If you do not hear the "Bi" prompt, please adjust the distance between the phone and the camera, and then click Next until you hear the prompt 2. If you hear the recognition prompt tone, the app still prompts that the camera is offline, please check the WiFi password, and reset the camera to re-configure the network to add -3- Next Input the device’s ID H00*********** 3-23-1 DeviceAdd 3-3 2 Next Input the device’s ID Note: Only some models support 5G WiFi Connect your phone to WiFi Input Wi-Fi password H00*********** office-wifi-2.4G *********** WiFi QR Connect 3 1 Next WiFi QR Connect Distance between QR code and camera lens is 10-30cm. When you hear ‘Bi’ sound, click ‘Next’. Home Device Modify Playback 3-53-6 Input device name to search device Settings 3-4 4 12 3 4 2023-09-13 1625:20 １ Playback Device 5 67891011 12 13 14 15 16 360P Pan&TiltIntercomPresetLighting 3.Solar panels Instructions 1. Power output: 3W/5V; 2. When installing, please face the board to a sunny direction; 3. When using with a camera, just connect the output line of the solar panel to the camera. Note: This solar panel can only be used with low-power battery cameras, not with regular IP cameras. -4- Introduction for monitoring interface: 9. Local record 10. Screenshots 11. Speaker 12. Pan&Tilt 1. App Settings 2. Scan code 3. Split Screen 4. Add 5. Settings 6. Full screen 7. Resolution 8. Up & down 13. Intercom 14. Playback 15. Preset 16. Lighting 360P -5- Settings Settings System Time Settings Video Settings Alarm Settings Record Settings Network Settings Security Settings Visitors Management Home FAQ-1FAQ-2FAQ-3 Add share user User authorization Visitor Operator Visitor Input new user’s APP ID User Remarks Share User Visitors Management Add FAQ: Share the camera with other users To protect the user's privacy, the first user is an administrator by default. Others need administrator's permission to access the camera, or they cannot login even with ID and password. The way to get permission as follows: Access the “SriHome” App, tap Settings -> Visitor Management -> Add. There are 2 types of permissions: Operator: Live video view, set time, alarm, record and network. Visitor: Viewing video only in real time Note: You can find the user's App ID in App Settings cámara de batería Manual de usuario rápido - La cámara con batería no es compatible con el modo de punto de acceso AP. - Esta cámara no admite WiFi de 5 GHz, solo admite WiFi de 2,4 GHz. - Verifique si DHCP está habilitado en el enrutador. Antes de comenzar la configuración DC 5V DC 5V ON/OFF RESET Micro SD - La cámara de batería de bajo consumo está equipada con 2 baterías 18650 de forma predeterminada, cargue las baterías antes de usar la cámara por primera vez. 1. Introducción de productos Paso 1. Instalación de la aplicación SriHome 2. Conexión del dispositivo Método 1: Busque "SriHome" en Google Play o iOS App Store. ON/OFF REINICIAR Ranura para tarjetas TF Ranura para tarjetas TF POWER ON/OFF REINICIAR ON 5VDC OFF -1- -2- Paso 2. Registro e inicio de sesión en la aplicación SriHome Paso 3. Encienda la cámara Método 2: Escanee el código QR para descargar la aplicación "SriHome". La cámara emitirá un "bip" continuo después de 30 segundos. Nota: Si no hay un "bip", mantenga presionado el botón "RESET" durante 5 segundos hasta que escuche un "bip" largo. Gire el interruptor de alimentación a ON y la cámara se encenderá. Etapa 4. Agregue la cámara a la aplicación SriHome Cuando escuche el “bip” continuo, siga las instrucciones de la aplicación SriHome para agregar el dispositivo, como en la figura: REINICIAR REINICIAR DC 5V ON/OFF RESET Micro SD ON/OFF ON/OFF ON 5VDC OFF AndroidiOS (forma predeterminada, cargue las baterías antes de usar la cámara por primera vez) Aviso: 1. Si no escucha el mensaje "Bi", ajuste la distancia entre el teléfono y la cámara, y luego haga clic en Siguiente hasta que escuche el mensaje 2. Si escucha el tono de aviso de reconocimiento, la aplicación aún indica que la cámara está fuera de línea, verifique la contraseña de WiFi y reinicie la cámara para volver a configurar la red para agregar. -3- Cámara 3-3 Siguiente Introduzca ID de los dispositivos H00*********** 3-2 Conectar WiFi QR 3-1 2 Siguiente Introduzca ID de los dispositivos Nota: solo algunos modelos admiten WiFi 5G Por favor conecte su teléfono a W iFi Entrada de contraseña Wi-Fi H00*********** office-wifi-2.4G *********** Conectar WiFi QR 3 1 Home Dispositivo Modificar Reproducción Ingrese el nombre del dispositivo para buscar el dispositivo Ajustes Siguiente Conexión WiFi QR 4 La distancia entre el código QR y la lente de la cámara es de 10-30 cm. Cuando escuche el sonido 'Bi', haga clic en 'Siguiente'. 3-4…

Text truncated - open the document above for the full version.

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:THREESTONESMEDIALLC FRN:0033401761 ContactName:SijieZhang Address:1200BroadwaySt.APT329,LosAngeles,CA90015 TelephoneNo:+12679093692 Email:[email protected] Applicant: Companyname:ShenzhenSricctvTechnologyCo.,Ltd ProductDescription: Granteecode:2A22Q FCCID:2A22Q-DH005 ContactName:KevinZhu Address:The4thFloorofbuilding40,5thIndustrialParkofHuaideCuigang,Fuyong Street,Bao'an,Shenzhen,China TelephoneNo:0755-29360806 Email:[email protected] [ShenzhenSricctvTechnologyCo.,Ltd]certifiesthat,asofthedateofthisfiling oftheapplicationwiththeTCB,[THREESTONESMEDIALLC]isourdesignated USagentforserviceofprocessfortheabovereferencedFCCID.[Shenzhen SricctvTechnologyCo.,Ltd]acceptstomaintainanagentfornolessthanone yearafterthegranteehasterminatedallmarketingandimportationorthe conclusionofanycommissionrelatedproceedinginvolvingequipment.[THREE STONESMEDIALLC]accepts,asofthedateofthefilingoftheapplication,the obligationofthedesignatedUSagentforserviceofprocessfortheabove referenceFCCID. TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. Wireless Battery Camera FRN:0031325327 1/1 Date:14/10/2023 Applicant’sName:KevinZhuUSAgent’sName:SijieZhang Title:ManagerTitle:President Signature Signature

C5266091_X24_Ed.2 1/1 “AttestationStatements” TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 TheCommissionadoptedrulesthatprohibitequipmentauthorizationfor“covered” telecommunicationsequipmentandvideosurveillanceequipmentproducedbyentitiesidentified ontheCommission’sCoveredList 1 ,whichisperiodicallyupdated.SeetheCoveredListformore details.ThisAttestationStatementistoconfirmthatwefollowtheSection2.911(d)(5)(i)-(ii) Applicant Companyname:ShenzhenSricctvTechnologyCo.,Ltd Granteecode:2A22Q FCCID:2A22Q-DH005 ContactName:KevinZhu Address:The4thFloorofbuilding40,5thIndustrialParkofHuaideCuigang,Fuyong Street,Bao'an,Shenzhen,China TelephoneNo:0755-29360806 FaxNo:0755-29924806 Email:[email protected] i.[ShenzhenSricctvTechnologyCo.,Ltd](“theapplicant”)certifiesthatthe equipmentforwhichauthorizationissoughtisnot“covered”equipment prohibitedfromreceivinganequipmentauthorizationpursuanttosection 2.903oftheFCCrules.Theapplicantmustsignthiscertification. ii.[ShenzhenSricctvTechnologyCo.,Ltd](“theapplicant”)certifiesthat,asof thedateofthefilingoftheapplication,theapplicantisnot(asaspecifically namedentityoranyofitssubsidiariesoraffiliates)identifiedontheCovered Listasanentityproducing“covered”equipment. Theapplicantmustsignthiscertification. ShenzhenSricctvTechnologyCo.,Ltdcertifiesthat,asofthedateofthefilingof theapplication,theapplicantisnotidentifiedontheCoveredListasanentity producing“covered”equipment. Date:14/10/2023 Applicant’sName:KevinZhu Title:GeneralManager Signature 1 TheCommission’sCoveredListispublishedbythePublicSafetyandHomelandSecurityBureauandpostedonthe Commission’swebsite.ThisCoveredList,whichisperiodicallyupdated,identifiesparticularequipment,producedby particularentities,thatconstitutes“covered”equipment.https://www.fcc.gov/supplychain/coveredlist

Shenzhen Sricctv Technology Co., Ltd Family models declaration letter. 10/23/2023 We Company: Shenzhen Sricctv Technology Co., Ltd Address: The 4th Floor of building 40, 5th Industrial Park of Huaide Cuigang, Fuyong Street, Bao'an, Shenzhen, China Product: Wireless Battery Camera Model Name: DH005 Family Model: DH001, DH002, DH003, DH004, DH006, DH007, DH008, DH009, DH010, DH011, DH012, DH013, DH014, DH015, DH016, SH033 All models use the same circuit and RF module, except the model name. We (Shenzhen Sricctv Technology Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.), same mechanical structure and design (including product enclosure, materials, etc.), the only difference is the All the model are the same circuit and RF module, except the model name. Thanks Sincerely, Signature [Name] Kevin Zhu [Title] Gernal manager [email protected]

C5266091_X8_Ed.1 1/1 LetterofAuthorization <ShenzhenSricctvTechnologyCo.,Ltd> Company:ShenzhenSricctvTechnologyCo.,Ltd Address:The4thFloorofbuilding40,5thIndustrialParkofHuaide Cuigang,FuyongStreet,Bao'an,Shenzhen,China ProductName:WirelessBatteryCamera ModelNumber:DH005,DH001,DH002,DH003,DH004,DH006, DH007,DH008,DH009,DH010,DH011,DH012,DH013,DH014, DH015,DH016,SH033 FCCIdentifier:2A22Q-DH005 WeauthorizeLGAITechnologicalCenterS.A.,RondadelaFontdelCarme,s/n, 08193Bellaterra,Spain,toactonourbehalfonallmattersconcerningthe abovenamedequipment. AnyindividualwithinLGAITechnologicalCenterS.A.isauthorizedtoactonour behalfandtakeactionontheapplication. WedeclarethatauthorizeLGAITechnologicalCenterS.A.,RondadelaFontdel Carme,s/n,08193Bellaterra,Spain,isallowedtoforwardallinformation relatedtotheapprovalprojecttotheFederalCommunicationCommissionand todiscussanyissuesconcerningtheapprovalapplication.Anyandallacts carriedoutbyLGAITechnologicalCenterS.A.onourbehalfshallhavethe sameeffectasactsofourown. Name:KevinZhuDate:14/10/2023 Title:GeneralManager Signatureofapplicant:

C5266091_X10_Ed.2 1/1 < ShenzhenSricctvTechnologyCo.,Ltd > OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046Date:14/10/2023 Subject:RequestforConfidentiality FCCID:2A22Q-DH005 ToWhomItMayConcern, PursuanttotheprovisionsofSections0.457and0.459ofCommission'srules (47CFR0.457,0.459),wearerequestingtheCommissiontowithholdthefollowing attachment(s)asconfidentialdocumentfrompublicdisclosure. ExhibitsLong-Term Confidentiality Short-Term Confidentiality NOTE2 IDLabel/Location AttestationStatement ExternalPhotos BlockDiagram Schematics TestReport TestSetupPhotos User’sManual NOTE 1 InternalPhotos NOTE 1 PartsList/TuneUp/BOMList RFExposureInfo OperationalDescription CoverLetter(s) FCCSoftwareSecurity RequirementsforUNIIdevices NOTE1:Long-TermConfidentialitymaybepermittedunderspecialconditions(SeeII.LONG-TERMCONFIDENTIALITY,Section3of KDB726920,uselastinforce) NOTE2:Short-TermConfidentialitycanberequestedforamaximumof180daysfromthedateofthegrant. Abovementioneddocumentcontainsdetailedsystemandequipmentdescriptionare consideredasproprietaryinformationinoperationoftheequipment.Thepublic disclosureofabovedocumentsmightbeharmfultoourcompanyandwouldgive competitoranunfairadvantageinthemarket. Incaseofshort-termConfidentiality,theapplicantrequeststheexhibitsselected abovearewithheldfrompublicviewforaperiodof_180_daysfromthedateofthe GrantofEquipmentAuthorizationandpriortomarketing. C5266091_X10_Ed.2 1/1 Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondentduringcertificationreviewprocesscannotbegrantedasconfidential documentsandthoseinformationwillbeavailableforpublicreviewoncethegrantof equipmentauthorizationisissued. Sincerely, Signature: Name:KevinZhu Title:GeneralManager

Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8

AQ- Label

Photo 1 Photo 2 Photo 3 Photo 4 ANT Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 Photo 11 Photo 12 Photo 13 Photo 14 Photo 15 Photo 16

FCC ID: 2A22Q-DH005 RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure (MPE) MPE Calculation Method E (V/m) ＝ d GP**30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Average RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 *377 **30 D GP From the EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Measurement Result Operation Frequency: BT: 2402-2480MHz Power density limited: 1mW/ cm 2 Antenna Type: External antenna Antenna gain: 1.91dBi, R=20cm conducted power Evaluation result Power density Limits (dBm)(mW)(dBi)Numeric 2412 16.02 16±117 50.1191.911.550.01551 2437 16.64 16±117 50.1191.911.550.01551 2462 16.58 16±117 50.1191.911.550.01551 2412 13.99 13±114 25.1191.911.550.00781 2437 13.15 13±114 25.1191.911.550.00781 2462 13.26 13±114 25.1191.911.550.00781 2412 12.55 12±113 19.9531.911.550.00621 2437 12.65 12±113 19.9531.911.550.00621 2462 12.64 12±113 19.9531.911.550.00621 (mW/cm2 )(mW/cm2) Antenna Gain 802.11b Max tune-up power Channel Freq. (MHz) modulation Tune-up power (dBm) (dBm) 802.11g 802.11n Conclusion: For the max result : 0.0155≤ 1.0 for Max Power Density, compliance RF exposure.. Signature: Date: 2023-10-17 NAME AND TITLE (Please print or type): Alex Li/Manager COMPANY (Please print or type): Shenzhen NTEK Testing Technology Co., Ltd./ 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen P.R. China.

Customer Name: Yuanchuangxing electronics (Shenzhen)CO.,LTD. SHENZHEN SRICCTV TECHNOLOGY CO.,LTD Customer Model: Customer Material No.: Customer Specification: Yuanchuangxing Material No.: Yuanchuangxing Specification Description: 5.06.0052 YCX08W-W689-250B White one-piece 104.5mm long waterproof 2.4G (with O- ring) Grey feeder 250mm long with terminals Specification Specification certificates Confirmation Signature Yuanchuangxing confirms Customer Confirmation sample making audits approval s validate audits approvals Yuanchua ngxing Client Date 2023-09-22 Date 2023-09-22 Yuanchuangxing electronics (Shenzhen) CO.,LTD Curricula vitae of documents created/revised/deleted versi on dates Production/revision of content draw up authorize note A1 2023.09.22 Zou Yangch en Yuanchuangxing electronics (Shenzhen)CO.,LTD. 3.catalogue 1, Cover .............................................. 1 2. Curriculum vitae of document creation/revision/repeal.................................2 3. Catalogue .......................................... 3 4、Product drawings .................................... 4 5. Passive performance test parameters .............. 5 6、2D、3D Performance Chart ............................ 7 7. Electrical performance test report ................... 7 8. Reliability test report .............................. 8 104.5±2 250±3 Yuanchuangxing electronics (Shenzhen)CO.,LTD. 7 6 5 4 3 REV. A1 2 1 CHANGE DESCRIPTION New DATE 2023.09.22 SIGNATURE zyc D D 6.30 C C Technical requirements: 1. Electrical parameters: 1.1 Impedance : 50Ω 1.2 Frequency : 2400-2500MHz B 1.3 VSWR : < 2.0 1.4 Peak Gain : ＜3dBi 1.5 Polarization : Linear 1.6 Radiation Patten: Omni directional 2. Mechanical properties: 2.1 Storage Temperature Range: -40 TO +85°C 2.2 Operating Temperature Range: -40 TO +85°C 3. All material must meet ROHS request 4. Mark( )as the key control dimensions TOLERANCE .XXX ±0.05 B Yuanchuangxing electronics (Shenzhen)CO.,LTD. Waterproof Golden grey white white 1 .XX ±0.1 .X ±0.2 1 X. ±0.25 2 XX. ±1 XXX. ±2 1 UNIT 1 mm DRAWED BY CHECKED BY APPROVED BY zyc Mike Sky A PART NO.: YCX08W-W689-250B TITLE: waterproof 2.4G NO. PART OR IDENTIFYING NO. 8 NOMENCLATURE OR DESCRIPTION 7 6 QTY 5 UNIT 4 MATERIAL AS DIMENSION 3 SCALE : 1 : 1 2 CAD FILE: DWG TYPE: PRODUCT DRAWING 1 6.5 20.7 Yuanchuangxing Electronics Yuanchuangxing electronics (Shenzhen)CO.,LTD. 1. Passive Performance Test Parameters Number Frequency (GHz) 2.4 2.45 2.5 VSWR 1.44 1.20 1.20 Yuanchuangxing electronics (Shenzhen)CO.,LTD. 6. 2D and 3D performance graph Passive Test For WiFi2.4G Freq (MHz) Effi (%) Gain (dBi) 2400 60 1.86 2450 61 1.82 2500 61 1.91 Yuanchuangxing electronics (Shenzhen)CO.,LTD. 7、Electrical performance parameters Electric al paramete rs frequency range 2.4GHz-2.5GHz Input Impedance 50Ω standing wave ratio (physics) <2.0 Control Sample Test Graph 2.4G-2.5G <3dBi gain (elect 5.15G-5.85G ronics ) polarisation mode vertical polarisation radiation direction in all directions connection method IPEX Mechanic al paramete rs length of a thread (e.g. of a parabo la) mainta ining power coaxial cable RF1.13 black Salt Spray 24H Test Environm ental paramete rs operating temperature -40~85°C Yuanchuangxing Electronics (Shenzhen) Co.,LTD 8. Reliability test report 8.1. Constant temperature and humidity tests Tests/pilot projects Constant temperature and humidity test checklist number Product Name/Specificatio n 2.4G-3dBi White One Piece Test Quantity: 5PCS Date of delivery: 2022-09-15 Completion date: 2022-09-16 Test/inspection equipment: 1.Programmable constant temperature and humidity test chamber 2.8753ES Network Analyser Test/inspection conditions: 1. Test at constant temperature -40°C for 12H 2. +85°65-70%RH test 12H, 24 hours total; Test Results Criteria for judgement: 1, the metal surface without cracks wrinkles, separation, etc.; non-metallic parts should not occur discolouration, cracking, deformation, degumming and other bad; 2、Electrical test meets the standard requirements; voltage VSWR test qualified Test/inspection determination: ☑ Qualified Failure No judgement Test: Li Chunqiang Audit: Wang Chunjiang Yuanchuangxing Electronics (Shenzhen) Co.,LTD 8.2 High and low temperature thermal shock Tests/pilot projects High and Low Temperature Cold and Heat Shock checklist number Product Name/Specificatio n 2.4G- 3dBi White One Piece Test Quantity: 5PCS Date of delivery: 2022-09-15 Completion date: 2021-09-16 Test/inspection equipment: 1.High and low temperature alternating humidity and heat box 2.8753ES Network Analyser Test/inspection conditions: -30°C (2H) - 80°C (2H) intervals, 6 cycles for 24 hours; Test Results Criteria for judgement: 3, metal surface plating should be no flaking, cracking wrinkles, separation, etc.; non- metallic parts should not occur discolouration, cracking, deformation, degumming and other bad; 4、Electrical test is in accordance with the standard; the voltage VSWR test is qualified. Test/inspection determination: ☑ Qualified Failure No judgement Test: Li Chunqiang Audit: Wang Chunjiang Yuanchuangxing electronics (Shenzhen)CO.,LTD. Specification for sample inspection of structural components Structural component sample inspection results shall contain the following: form Specific ation items form Specific ation items ①App earan ce & Gauge integri ty testing 1、Check the surface with or without water folder, gas pattern, shrinkage, whitening, scratches, bruises, material flowers, oil stains and so on. ③Reli abilit y perfor mance test (machin ery etc) 1. Storage temperature range 2、Check the edges, rubber pillars, limits, orifices, window Grids, slots, etc., there is no batch of peaks, go glue is not flush, broken columns, edge collapse, water cut flat, material brittle and so on. 2、Operating temperature range 3、Flame retardant 3. Tapping into the appropriate specification screws, which must not be whitened. Bursting or sliding teeth 4、Drop test 4, check the surface treatment (oil spraying, silkscreen, hot stam…

Text truncated - open the document above for the full version.

Report No.: S23072503511001 Version.1.3 Page 1 of 66 FCC RADIO TEST REPORT FCC ID:2A22Q-DH005 Product: Wireless Battery Camera Trade Mark: SriHome / Sricam Model No.: DH005 Family Model: DH001, DH002, DH003, DH004, DH006, DH007, DH008, DH009, DH010, DH011, DH012, DH013, DH014, DH015, DH016, SH033 Report No.: S23072503511001 Issue Date: Sep 15, 2023 Prepared for Shenzhen Sricctv Technology Co., Ltd The 4th Floor of building 40, 5th Industrial Park of Huaide Cuigang, Fuyong Street, Bao'an, Shenzhen, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen 518126 P.R. China Tel. 400-800-6106, 0755-2320 0050, 0755-2320 0090 Website: http://www.ntek.org.cn Report No.: S23072503511001 Version.1.3 Page 2 of 66 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ...................................................................................................................... 3 2 SUMMARY OF TEST RESULTS ......................................................................................................................... 4 3 FACILITIES AND ACCREDITATIONS ............................................................................................................. 5 3.1 FACILITIES..................................................................................................................................................... 5 3.2 LABORATORY ACCREDITATIONS AND LISTINGS ................................................................................. 5 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................... 5 4 GENERAL DESCRIPTION OF EUT .................................................................................................................. 6 5 DESCRIPTION OF TEST MODES ..................................................................................................................... 8 6 SETUP OF EQUIPMENT UNDER TEST ......................................................................................................... 10 6.1 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ..................................................................... 10 6.2 SUPPORT EQUIPMENT............................................................................................................................... 11 6.3 EQUIPMENTS LIST FOR ALL TEST ITEMS .............................................................................................. 12 7 TEST REQUIREMENTS .................................................................................................................................... 14 7.1 CONDUCTED EMISSIONS TEST ............................................................................................................... 14 7.2 RADIATED SPURIOUS EMISSION ............................................................................................................ 17 7.3 6DB BANDWIDTH ....................................................................................................................................... 26 7.4 DUTY CYCLE ............................................................................................................................................... 28 7.5 MAXIMUM OUTPUT POWER .................................................................................................................... 29 7.6 POWER SPECTRAL DENSITY ................................................................................................................... 31 7.7 CONDUCTED BAND EDGE MEASUREMENT......................................................................................... 33 7.8 SPURIOUS RF CONDUCTED EMISSIONS................................................................................................ 35 7.9 ANTENNA APPLICATION .......................................................................................................................... 36 8 TEST RESULTS ................................................................................................................................................... 37 8.1 MAXIMUM CONDUCTED OUTPUT POWER ....................................................................................................... 37 8.2 -6DB BANDWIDTH .......................................................................................................................................... 38 8.3 MAXIMUM POWER SPECTRAL DENSITY LEVEL ............................................................................................... 44 8.4 BAND EDGE .................................................................................................................................................... 50 8.5 CONDUCTED RF SPURIOUS EMISSION ............................................................................................................. 57 Report No.: S23072503511001 Version.1.3 Page 3 of 66 1 TEST RESULT CERTIFICATION Applicant’s name ......................... : Shenzhen Sricctv Technology Co., Ltd Address ....................................... : The 4th Floor of building 40, 5th Industrial Park of Huaide Cuigang, Fuyong Street, Bao'an, Shenzhen, China Manufacturer's Name .................. : Shenzhen Sricctv Technology Co., Ltd Address ....................................... : The 4th Floor of building 40, 5th Industrial Park of Huaide Cuigang, Fuyong Street, Bao'an, Shenzhen, China Product description Product name .............................. : Wireless Battery Camera Model and/or type reference ..... : DH005 Family Model ............................... : DH001, DH002, DH003, DH004, DH006, DH007, DH008, DH009, DH010, DH011, DH012, DH013, DH014, DH015, DH016, SH033 Test Sample Number ................................. : S230725035011 Measurement Procedure Used: APPLICABLE STANDARDS APPLICABLE STANDARD/ TEST PROCEDURE TEST RESULT FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part …

Text truncated - open the document above for the full version.

Radiated Measurement Photos Conducted Measurement Photos