2A26U-ML0YIS1APortable Desk Lamp

Instruction Manual Portable LED Desk Lamp with Wireless Charger To Our Customers Thank you for purchasing our products. Please read this manual carefully before use so that the lamp can be used correctly. Please keep it for reference at anytime. Safety PrecautionsTo prevent damage to persons and property, please be sure to follow these instructions. WARNING Do not use this desk lamp in an unstable place to avoid tipping and causing the lamp to break. Please do not cover the lamp with flammable materials such as cloth or paper to avoid fire accidents. If the external flexible cable or flexible wire of this lamp is damaged, the wire is to be replaced by the manufacturer or its service provider or a similarly qualified person to avoid danger. Please do not insert metal products or flammable objects into the lamp to avoid electric shock, fire and other accidents. Please do not place the lamp next to the wind or high temperature or flammable objects, to avoid electric shock, fire and other accidents. Do not pull or bend the power cable by force. Damage to the power cable may lead to fire, electric shock and other accidents. Please do not transform the lamp, replace the parts by yourself, to avoid causing electric shock, fire and other accidents. Please use at the stated voltage rating (rated voltage 100-240V 50/60~Hz). Use for a long time beyond the rated voltage range may cause the lamp to fire by overheating. If an abnormality occurs, quickly disconnect the power and contact the reseller. When unplugging the LED control unit, please do not pull the power wire to prevent the power wire from being damaged and causing fire and electric shock. Please do not plug and unplug the LED control device with wet hands to avoid electric shock accidents. The lamp is not waterproof nor moisture-proof, only suitable for use in dry indoor occasions. Improper use may lead to electric shock and other occurrences. The light source in this lamp should be replaced by the manufacturer or its service agent or someone with similar qualifications. NOTICE Always make sure you have removed all packaging accessories and tape from the light before installation to prevent fire. Do not use with dimming devices such as light controllers and brightness adjustment switches to avoid fire and other accidents. Please avoid direct sunlight on the lamp, and away from the heating source, otherwise it will lead to discoloration, damage or failure of the lamp; when the lamp is turned on and just after the lamp is turned off, there will be a slight sound due to the expansion and contraction of the plastic of the lamp, this is a normal phenomenon, not a fault. There is normal color difference of LED light source, even if the same category of goods, there are normal differences in light color and brightness. Please unplug the LED control device from the socket when the lamp is not used for a long time to prevent fire accidents. When there are too many devices connected to the terminal block, the LED lamp may flicker abnormally, please disconnect the device that impacts the lamp. When using the lamp near the radio or TV set, the radio or TV set may have murmur. When using the lamp near the remote control TV, the remote control may malfunction. (Solution: change the direction of Lamp usage or use the remote control away from the Lamp) ● ● When You Suspect a Fault Be sure to disconnect the power supply to prevent electric shock. FaultsReasons Solutions LED does not light upThe LED control device plug offPlug the LED control unit into the power supply LED lights go out during use Instantaneous power failure or low voltageTurn off the light for more than 3s and then turn it on again If the fault is not contacted or abnormalities are found after inspection, be sure to unplug the power supply and then get in touch with us by Amazon messages or email: [email protected]. To use this product safely and efficiently, please clean and inspect it regularly (once every 6 months). Failure to do so may result in fire, electric shock, or light fall if used for a long period of time. Insecticide Repair and MaintenanceBe sure to disconnect the power supply to prevent electric shock. When the lamp needs to be cleaned, please use a cloth dipped in neutral detergent to wipe after wringing, then wipe with a dry cloth, do not use sharp objects to touch the surface of the lamp. Do not use detergents or organic solvents other than neutral detergents to wipe the lamp to avoid problems such as discoloration, deterioration, strength reduction or damage to the lamp. Do not spray insecticide on the lamp, as this may cause discoloration and damage to the lamp. Specifications Model ML0YIS1A Input Voltage100-240V Frequency 50/60~Hz Rated Current0.16A Power Rated Power: 34W Lighting Power: 21W (154*0.2W/LED module) Wireless Charging: 9V/1.1A (MAX. 10W) Wireless Charging QI Standard PF 0.5 LED Quantities Color Temperature 154 Reading Mode: 4000K Working Mode: 6000K Materail Aluminum + Metal Brightness DimmingAutomatic Dimming + Touch Dimming NOTES on the Operation of Touch Dimmers Model: ML0YIS1A The touch dimmers are capable of sensing subtle changes with high sensitivity. It may not function properly in the following states of use: 1. Instead of using your fingers, when you touch the dimmer panel with your whole hand, or when you touch the dimmer panel with objects other than your fingers (gloves, ball point pen, etc.). 2. When gently touching or touching the dimming board for a short time instantly. 3. When used in places with rapid temperature changes. 4. When the external interference is strong. It is possible to execute the relevant function when touching near the touch dimmer panel. Be sure to disconnect the power supply to prevent electric shock. Component Name and Installation Method Gesture Infrared Sensor Receiver Lamphead Upper Light Arm Shaft Cover Shaft Cover The Lower Light Arm Wireless Charging Sensor Window Touch Button LED Module Other LED modules ca…

Text truncated - open the document above for the full version.

Page 1 of 1 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L3.5cm x 3.0cm) Label Location Portable Desk Lamp Model: ML0YIS1A FCC ID: 2A26U-ML0YIS1A

Page 1 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Page 2 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Coil Antenna Page 4 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 6 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11

Page 1 of 10 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity RF Exposure Evaluation Report 1. Product Information FCC ID: 2A26U-ML0YIS1A Product Name Portable Desk Lamp Model Number ML0YIS1A Power Supply For AC Adapter Input: 100-240V~, 50/60Hz, 1.0A For AC Adapter Output: 24V1.5A Wireless output:10W Modulation Type ASK Frequency Range 111.0~205.0KHz Operation Frequency 125 KHz Antenna Type Coil Antenna Hardware version / Software version / Accessories / Exposure category General population/uncontrolled environment EUT Type Production Unit Device Type Mobile Device 2. Evaluation Method Per KDB 680106 D01 Section 3. RF Exposure Requirements; 1) Consumer wireless power transfer devices approved under Part 18 in some cases have to demonstrate compliance with RF exposure requirements. The potential for exposure must be assessed according to the operating configurations of the wireless system and the exposure conditions of users and bystanders. RF exposure must be evaluated with the client device(s) being charged by the primary at maximum output power. The RF exposure requirements must be determined in conjunction with the device operating characteristics, according to the mobile and portable exposure requirements in Section 2.1091 and Section 2.1093 of the rules. SAR and MPE limits do not cover the frequency range for wireless power transfer applications which operate below 100 kHz and 300 kHz respectively; therefore, RF exposure compliance needs to be determined with respect to 1.1307 (c) and (d) of the FCC rules. 2) Based on the design and implementation of the power transfer application, it must be clearly identified if mobile or portable RF exposure conditions apply. Devices that are installed to provide separation of at least 20 cm from users and bystanders may qualify for mobile exposure conditions. For some conditions where users and bystanders may be exposed at closer than 20 cm, section 2.1091(d) (4) of the rules may apply. 3) For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance of 15 cm. E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s) to the edge of the Page 2 of 10 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity device. Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63 A/m. A KDB inquiry is required to determine the applicable exposure limits below 100 kHz. 4) Portable exposure conditions from 100 kHz to 6 GHz are determined with respect to SAR requirements. Existing SAR systems and test procedures are generally intended for measurements above 100 MHz. While numerical modeling can be an alternative, the constraints of substantial computational resources at low frequencies could introduce further limitations. Under these circumstances, including operations below 100 kHz, the Commission may consider a combination of analytical analysis, field strength, radiated and conducted power measurements, in conjunction with some limited numerical modeling to assess compliance. 5) Depending on the operating frequency, existing SAR and MPE measurement procedures may be adapted to evaluate wireless power transfer devices for compliance with respect to mobile or portable exposure conditions. If the grantee or its test lab have any questions regarding RF exposure evaluation they should contact the FCC Laboratory with sufficient system operating configuration details to determine if RF exposure evaluation is necessary and, if required, how to apply specific test procedures. Below 100 MHz, when SAR testing is required and the device is operating at close proximity to persons, information on device design, implementation, operating configurations, exposure conditions of users and bystanders are needed to determine the evaluation and testing requirements. In addition, the influence of nearby objects may also need consideration according to the wireless power transfer system implementation; for example, the effects of placing the device, its coils or radiating elements on or near metallic surfaces 3. Evaluation Limit 3.1 Refer evaluation method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 680106 D01 RF Exposure Wireless Charging Apps v03: RF Exposure Considerations for Low Power Consumer Wireless Power Transfer Applications FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices FCC CFR 47 part 18.107:Indusial, Scientific, and Medical Equipment Page 3 of 10 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 3.2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) …

Text truncated - open the document above for the full version.

Shenzhen Magelighting Co., Ltd. Desk Lamp Supplier company name：Shenzhen Magelighting Co., Ltd. supplier name：Wireless charging and transmitting coil supplier address：A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Unit:mm Shenzhen Magelighting Co., Ltd. Desk Lamp

Page 1 of 23 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT For Shenzhen Magelighting Co., Ltd. Portable Desk Lamp Test Model: ML0YIS1A Prepared for : Shenzhen Magelighting Co., Ltd. Address : A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : September 21, 2022 Number of tested samples : 2 Serial number : 220307167A-1, 220307167A-2 Date of Test : September 21, 2022 ~ October 10, 2022 Date of Report : October 10, 2022 Page 2 of 23 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15C Report Reference No. ................ : LCS220307167AEA Date Of Issue ................................. : October 10, 2022 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address .......................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure .......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : Shenzhen Magelighting Co., Ltd. Address .......................................... : A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Test Specification Standard ......................................... : FCC CFR 47 PART 15C Test Report Form No. .................... : LCSEMC-1.0 TRF Originator................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. .................. : Portable Desk Lamp Trade Mark ..................................... : MG Test Model ...................................... : ML0YIS1A Power Supply ................................. : For AC Adapter Input: 100-240V~, 50/60Hz, 1.0A For AC Adapter Output: 24V1.5A Wireless output:10W Result ........................................... : Positive Compiled by: Supervised by: Approved by: Kay Hu/ Administrator Cary Luo/ Technique principal Gavin Liang/ Manager Page 3 of 23 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS220307167AEA October 10, 2022 Date of issue Test Model.............................. : ML0YIS1A EUT......................................... : Portable Desk Lamp Applicant............................... : Shenzhen Magelighting Co., Ltd. Address................................... : A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Shenzhen Magelighting Co., Ltd. Address................................... : A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Telephone............................... : / Fax.......................................... : / Factory................................... : Shenzhen Magelighting Co., Ltd. Address................................... : A 5/F Building B, Chuangye 3rd Road, Fenghuang 3rd Industrial Zone, Fuyong Town, Bao’an District Shenzhen China Telephone............................... : / Fax.......................................... : / Page 4 of 23 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Revision History Report Version Issue Date Revision Content Revised By 000 October 10, 2022 Initial Issue --- Page 5 of 23 FCC ID: 2A26U-ML0YIS1A Report No.: LCS220307167AEA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoa…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Setup Photos of the EUT Conducted Emission Radiated Emission below 30MHz Page 2 of 2 FCC ID: 2A26U-ML0YIS1A Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Radiated Emission from 30MHz to 1GHz