2A2BO-EMV3000RFID Reader

Product user manual & operation description EMV3000 Document number: 915-11135-01 Product user manual & operation description EMV3000 Document number: 915-11135-01 Page 2 | 26 Document version Version Date Author Description 01 16/06/2021 Emsyscon Draft release FCC and IC compliance statement EMV3000 This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Emsyscon Solutions may void the FCC authorisation to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Disclaimer The information provided in this document is accurate at the time of publication and supersedes any other version(s). However, Emsyscon reserves the right to make changes without prior notice. © This material is copyright and may not be reproduced, stored in a retrieval system or transmitted in any form or by any means in whole or in part without the express written consent of Emsyscon. This material is confidential to Emsyscon and may not be disclosed in whole or in part to any third party nor used in any manner whatsoever other than for the purposes expressly consented to by Emsyscon in writing. Emsyscon assumes no responsibility for any inaccuracies, errors, omissions or consequences arising out of the use of this material. Product user manual & operation description EMV3000 Document number: 915-11135-01 Page 3 | 26 Table of Contents 1 INTRODUCTION ..................................................................................................................................................................................7 1.1 EMV3000 ......................................................................................................................................................................................7 1.2 EMV3000 Key features ............................................................................................................................................................7 1.3 EMV3000 Mechanical ..............................................................................................................................................................7 1.4 EMV3000 Environmental ........................................................................................................................................................7 1.5 EMV3000 Electronic and operation ................................................................................................................................... 8 1.6 EMV3000 Identification label ............................................................................................................................................... 9 1.7 EMV3000 Mechanical dimensions .................................................................................................................................... 10 1.8 Used symbols ........................................................................................................................................................................... 11 1.9 General guidelines .................................................................................................................................................................. 11 2 SAFETY INFORMATION .................................................................................................................................................................. 12 2.1 General safety .......................................................................................................................................................................... 12 2.2 Electrical safety ........................................................................................................................................................................ 13 2.3 Safety inspection checklist ................................................................................................................................................... 14 2.4 Handling devices that are sensitive to electrostatic discharge ............................................................................... 15 2.5 Safety notices ........................................................................................................................................................................... 16 3 GENERAL INSTALLATION GUIDELINES ..................................................................................................................................... 17 4 INSTALLATION TOOLING LIST ......................................................................................................…

Text truncated - open the document above for the full version.

Document Version 1.1 2020-10-30 LONG-TERM CONFIDENTIALITY REQUEST for Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 TO WHOM IT M AY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request Long-Term Confidentiality for the following product: For the product stated above, we request Long-Term Confidentiality for exhibits which contain Block Diagram, Operational Description, Parts List/Tune Up Info, Schematics, SDR Software/Security Info. The above exhibits contain ou r trade secrets and proprietary information that could be of benefit to o ur competitors. This information will not be publicly available. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Company Name: Phone: Company Address: Fax: E-mail: Contact Name: Signature: Signature Date: Check your GC here. Click Grantee Search. FCC I D: Grantee Code Equipment Product Code

Annex A 1-1469/20-01-01_AnnexA External photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Tobias Wittenmeier Testing Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2021-07-29Document No. 1-1469/20-01-01_AnnexA2/6 Photo 3 Photo 4 2021-07-29Document No. 1-1469/20-01-01_AnnexA3/6 Photo 5 Photo 6 2021-07-29Document No. 1-1469/20-01-01_AnnexA4/6 Photo 7 2021-07-29Document No. 1-1469/20-01-01_AnnexA5/6 Document history VersionApplied changesDate of release initial release2021-07-29 - END OF DOCUMENT - 2021-07-29Document No. 1-1469/20-01-01_AnnexA6/6

123456789 PRO PRIET ARY INFORMAT ION: This information is confidentia l and proprie ta ry to Ems yscon, e xcept if specifically authoris ed in writing by Emsyscon. The holde r of this document: (1 ) s hall ke ep all information containe d he re in confidential a nd s hall prote ct s ame in whole or in part from dis closure a nd diss emina tion to a ny third party, (2 ) shall us e s ame for ope ra ting and maintenance purposes only. NOT ES: 1. All dimensions are in millimetres, f orma t Width x Height (W xH), unless otherwise specified. 2. ( ) Indicate de signations shown f or inf ormation only and not to be marked. 3. All parts , finishe s, paints and ink must comply with Europea n Directive s 20 02 /95/ EC (RoHS), 20 11/6 5/EU (RoHS recas t), 20 02 /96/EC (W EEE) and 20 12/ 19 /EU (W EEE recas t). C A B D E F G H I 123456789 C A B D E F G H I Label layout:Label specifications: Serial: Total of 18 digits (from left to right) consisting of: ▪ Position 01-04: Emsyscon unique manufacturer code (xxxx) ▪ Position 05-08: Month and ye ar of production (mmyy) ▪ Position 09-13: Emsyscon unique article number (ppppp) (no prefix, no version numbe r) ▪ Position 14-18: Product serial number batch range (sssss), starting from [m]0001 Examples: 100107201021300001, 101007201021350001, 107507 201021370001 1712175.5 1 7 Label position: Backside EMV 3000 Barcode:EAN128 Product label: barcode height 5mm SAM label: barcode height 5mm Label(s):Product label 50.80x25.40mm, printing surface 49.5x24.5mm SAM/SIM label: 25.40x12.70mm Text:Product label: Segoe UI 5pt black SAM/SIM label: Se goe UI 6pt black Width=20mm, height=4.5mmLogo: [...]:Replace with country of manufacturing, e.g. Netherlands, Romania... (CoO: Country of Origin) Rev:See ECNs for up-to-date information on the revision version of this product Line(s):Inne r/outer line width=0.1pt Width=5mm, height=4mm Width=4mm, height=5mm CE marking: WEEE symbol: 4 Article description: PRLI Product Label Identification format EPR EMV3000- 1 Drawn by: Ems yscon Date: 16/06/2021 Scale: 1:1 (printing) Filename: 905-10269-05 Size: A4 Sheet 1 of 1 Ems ys con16 /06/ 202 105Add FCC Ems ys con30 /01/ 201 904Update WEE E symbol Ems ys con21 /11/20 1803Review automotive certification Ems ys con29 /10/ 201 802Revise label layout Ems ys con03 /03 /20 2101First releas e Author Date dd/mm/ yyyy Ve rsionDescri ption BOM reference: ▪ Product blank la bel: 300-10271-yy, LAB Thermal transfer SN product 50.80x25.40mm polyeste r silver tamper-proof (Brady THT-17-438-3). Printing surface 48.80x23.40mm. ▪ SAM/SIM label: 300-10382-yy, LAB Thermal transfer SN product WH 25.40x12.70mm satin vinyl tamper-proof (Brady THT-5-7351-10). Attention: ▪ Ask for spe cific instructions if the product contains a SAM and/or SIM. SAM and/or SIM label layout (if applicable): SAM ID: xxxxxxxx SIM: PRJ Where “PRJ” = Min. thre e letter abbreviation indicating the project (to be defined by Ems yscon). Examples: DLN (De Lijn), ARR (Arriva), VES (Vestische), CAR (Cartel), KRC (Kenya Railway Corporation) ... Or label “NO SAM” and/or “NO SIM” if specifically requeste d by Emsyscon. PRJ Important notice: specific serial number range per manufacturer code: ▪ Elemaster:[1001][mmyy][xxxxx][00001] ▪ Head:[1010][mmyy][xxxxx][50001] ▪ CDS:[1075][mmyy][xxxxx][70001] Type :EM V30 00Article: Ve rsion: 25 0-10 21 3-01 1 xxxxmm yy10 21 3sssss Power: Rev.:1/ 2/3 /4 /5/ 6/7 /8 /9 5V , 1.0 A Ma de in/CoO : [...] FW: 91 11 01 09 SBL: 0 00 00 10 5 Emsyscon S olutions SRL - Romania Str. O borului 21 cam. 12 , 11 53 00 Curte a de Arges PCI a pproval n° : 4-40284 13.2 (2.2) Important notice concerning the serial numbering of EMV3000 readers: Continuous serial numbering regardless of EMV3000 version! HVIN :25 0-11 06 2-01 Width=5mm, height=4.2mmFCC marking: FCC ID: 2A 2BO-EM V30 00IC: 2 73 90-EM V30 00 Type :EM V30 00Article: Ve rsion: 25 0-10 21 3-01 1 xxxxmm yy10 21 3sssss Power: Rev.:1/ 2/3 /4 /5/ 6/7 /8 /9 5V , 1.0 A Ma de in/CoO : [...] FW: 91 11 01 09 SBL: 0 00 00 10 5 Emsyscon S olutions SRL - Romania Str. O borului 21 cam. 12 , 11 53 00 Curte a de Arges PCI a pproval n° : 4-40284 HVIN :25 0-11 06 2-01 FCC ID: 2A 2BO-EM V30 00IC: 2 73 90-EM V30 00

Annex B 1-1469/20-01-01_AnnexB Internal photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Tobias Wittenmeier Testing Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2021-07-29Document No. 1-1469/20-01-01_AnnexB2/5 Photo 3 Photo 4 2021-07-29Document No. 1-1469/20-01-01_AnnexB3/5 Photo 5 2021-07-29Document No. 1-1469/20-01-01_AnnexB4/5 Document history VersionApplied changesDate of release initial release2021-07-29 - END OF DOCUMENT - 2021-07-29Document No. 1-1469/20-01-01_AnnexB5/5

TEST REPORT Test report no.: 1-1469/20-01-02 Testing laboratory Applicant CTC advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://www.ctcadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12076-01. Emsyscon Solutions SRL Strada Oboruliu 21 cam 12 115300 Curtea De Arges / ROMANIA Phone: +32 472 060 527 Contact: Carine Fluyt e-mail: [email protected] Manufacturer Emsyscon Solutions SRL Strada Oboruliu 21 cam 12 115300 Curtea De Arges / ROMANIA Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 210 Issue 10 Spectrum Management and Telecommunications Radio Standards Specification - Licence-Exempt Radio Apparatus: Category I Equipment For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: RFID Reader Model name: EMV 3000 FCC ID: 2A2BO-EMV3000 IC: 27390-EMV3000 Frequency: 13.56 MHz Technology tested: RFID Antenna: Integrated PCB antenna Power supply: 4.75 V to 5.25 V DC by USB Temperature range: -20°C to +55°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Christoph Schneider Tobias Wittenmeier Lab Manager Testing Manager Radio Communications Radio Communications Test report no.: 1-1469/20-01-02 © CTC advanced GmbH Page 2 of 30 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes and disclaimer .......................................................................................................................... 3 2.2 Application details ............................................................................................................................... 3 2.3 Test laboratories sub-contracted ...................................................................................................... 3 3 Test standard/s, references and accreditations .......................................................................................... 4 4 Reporting statements of conformity – decision rule .................................................................................. 5 5 Test environment ............................................................................................................................................ 6 6 Test item .......................................................................................................................................................... 6 6.1 General description ............................................................................................................................. 6 6.2 Additional information ........................................................................................................................ 6 7 Description of the test setup ......................................................................................................................... 7 7.1 Shielded semi anechoic chamber ...................................................................................................... 8 7.2 Shielded fully anechoic chamber .................................................................................................... 10 7.3 AC conducted .................................................................................................................................... 11 7.4 RF measurements normal and extreme conditions ....................................................................... 12 8 Sequence of testing ..................................................................................................................................... 13 8.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ............................................................... 13 8.2 Sequence of testing radiated spurious 30 MHz to 1 GHz .............................................................. 14 9 Measurement uncertainty ............................................................................................................................ 15 10 Summary of measurement results .......................................................................................................... 16 11 Additional comments ............................................................................................................................... 16 12 Measurement results ................................................................................................................................ 17 12.1 Occupied bandwidth ...................................................................................................................... 17 12.2 Field strength of the fundamental ................................................................................................ 19 12.3 Field strength of the harmonics and spurious ........................................................................... 20 12.4 Conducted limits ............................................................................................................................ 23 12.5 Frequency error ...............................................................................................…

Text truncated - open the document above for the full version.

Annex D 1-1469/20-01-01_AnnexD Setup photos of the Equipment Under Test This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Tobias Wittenmeier Testing Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Str. 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Photos Photo 1 Photo 2 2021-07-29Document No. 1-1469/20-01-01_AnnexD2/7 Photo 3 Photo 4 2021-07-29Document No. 1-1469/20-01-01_AnnexD3/7 Photo 5 Photo 6 2021-07-29Document No. 1-1469/20-01-01_AnnexD4/7 Photo 7 Photo 8 2021-07-29Document No. 1-1469/20-01-01_AnnexD5/7 Photo 9 2021-07-29Document No. 1-1469/20-01-01_AnnexD6/7 Document history VersionApplied changesDate of release initial release2021-07-29 - END OF DOCUMENT - 2021-07-29Document No. 1-1469/20-01-01_AnnexD7/7