2A2CU-AB02Queen Scepter

User Manual Guide to Important Product Information EU CE Directive: is the collective name of series of product standards is issued by the European Union; enterprises complying with the standard may apply for CE certification mark on their products and labeling. Declaration Of Conformity Hereby, DRYWELL Declares that this Queen’s Scepter is in compliance with the essential requirements and other relevant provisions of directive 1995/5/EC. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning! Proper maintenance and care may extend the product’s service life. Before using the product, please read the following safety instruction carefully. 1. Please comply with the following before using the product:  Clean the product completely: Scrub it with an antibacterial soap and then wash with clean hot warm water; at last, wipe it gently with towel or soft cloth. 2. During using the product  No using massage oil or hand cream as lubricant.  No using silicon-based lubricant, because it’ll damage the organosilicone surface. Reminder: Do not use any cleaning agent containing alcohol, gasoline or acetone to wipe the product. Avoid direct solar radiation and long-time exposure to the high-temperature environment. The product shall be stored in a clean and dry place without contact with other plastic products. Maintenance of the Built-in Battery:  This product uses rechargeable batteries. A new battery could play its full effectiveness after two or three charging and discharging processes.  A battery can be charged or discharged for over 100 times and will go matured finally. After being charged fully, the battery shall be disconnected with the charger, or overcharge may reduce the battery life.  When the product is idle, the electric quantity of fully charged battery will lose gradually.  If the product is placed in a too hot or cold place, it will reduce the battery capacity and shorten the battery life. If the battery is too hot or cold, the battery life will be also short even though it is charged fully. Battery Warning!  When the battery is operated by mistake, it will fire or cause chemical burn. Explosion may happen when the battery is damaged.  The battery shall be disposed in accordance with the local laws and regulations. If possible, please recycle it. Users shall not take out or replace the battery by themselves; Otherwise, the risky operation may damage the product. For after-sales service, please contact 400-6666-276 Operation Instructions Step 1 1. For the first use, long press " " and release it after the second vibration to enter the "calibration mode". Step 2 1. Two devices: long press " " for 1 second, and the red work indicator lights up. 2. Power on will enter "PressureSensoner Mode" by default. Step 3 1. As shown in the figure, hold the control end of the wand. 2. The equipment will increase or decrease the vibration intensity of the equipment according to the pressure intensity. 3. At this point, the new function has been unlocked, allowing you to play for a while, remember to come back and unlock more ways to play. Step 4 1. 1 Click the button " " on the scepter, two devices will vibrate and enter the "offline mode". 2. Click the " " to adjust the vibration intensity under the "offline mode" and two devices can be used individually. 3. Click the " " on the scepter again to the "PressureSensoner Mode". 4. Press the two " " to turn off the device. Product description Online mode 1. Click " " 1s to start the two devices and enter the "PressureSensoner Mode" Offline mode Vibrator 1. Click" " to switch gears (1-2-3) 2. Click" "1s to shut down Wand: 1. Click " " to switch to "offline mode" 2. Click to switch to "PressureSensoner Mode" Calibration mode Wand: 1. Click" " 5s to release after twice vibration and enter "calibration mode"

Shenzhen DRYWELL Intelligent Technology Co., Ltd Agent Authorization Company: Shenzhen DRYWELL Intelligent Technology Co., Ltd Address: 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Product Name: Queen Scepter Trade Mark: DRYWELL Model Number: AB02 FCC ID: 2A2CU-AB02 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-06-25 Name: Sammy Zhang Title: Overseas Director Company: Shenzhen DRYWELL Intelligent Technology Co., Ltd

Shenzhen DRYWELL Intelligent Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-06-25 Subject; Request for Confidentiality FCC ID: 2A2CU-AB02 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Sammy Zhang Title: Overseas Director

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Fig.5 Fig.6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size: L1.0cm*W0.5cm Label Location FCC ID: 2A2CU-AB02

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 1. INTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Fig.3 Fig.4 2.4G Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Fig.5

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Report No.: LCS210617080AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 32 FCC TEST REPORT FOR Shenzhen DRYWELL Intelligent Technology Co., Ltd Queen Scepter Test Model: AB02 Prepared for : Shenzhen DRYWELL Intelligent Technology Co., Ltd Address : 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Shajing Street, Bao’an District, Shenzhen, Guangdong, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : June 17, 2021 Number of tested samples : 1 Sample number : 210617080A Sample number : Prototype Date of Test : June 17, 2021 ~ June 25, 2021 Date of Report : June 25, 2021 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Report No.: LCS210617080AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 32 FCC TEST REPORT FCC CFR 47 PART 15 C(15.249) Report Reference No. ................. : LCS210617080AEA Date of Issue................................... : June 25, 2021 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Shajing Street, Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure .......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : Shenzhen DRYWELL Intelligent Technology Co., Ltd Address ........................................... : 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Test Specification Standard ......................................... : FCC CFR 47 PART 15 C(15.249) / ANSI C63.10: 2013 Test Report Form No. ..................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2019-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. .................. : Queen Scepter Trade Mark ..................................... : DRYWELL Test Model ...................................... : AB02 Ratings ............................................ : DC 3.7V By Battery(500mAh) Recharged By DC 5V 1A Result ........................................... : Positive Compiled by: Supervised by: Approved by: Lh Li/ Administrators Jin Wang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Report No.: LCS210617080AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 32 FCC -- TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS210617080AEA June 25, 2021 Date of issue Test Model.............................. : AB02 EUT......................................... : Queen Scepter Applicant............................... : Shenzhen DRYWELL Intelligent Technology Co., Ltd Address.................................. : 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Shenzhen DRYWELL Intelligent Technology Co., Ltd Address................................... : 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Telephone............................... : / Fax.......................................... : / Factory................................... : Shenzhen DRYWELL Intelligent Technology Co., Ltd Address................................... : 301 Plant, Building 35, Lianchuang Technology Park Phase 3, Bulan Road No.21, Nanwan Street, Longgang Dist, Shenzhen, GD, CN China Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Report No.: LCS210617080AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 32 Revision History Revision Issue Date Revisions Revised By 000 June 25, 2021 Initial Issue Gavin Liang SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 Report No.: LCS210617080AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 32 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................................... 6 1.1 DESCRIPTION OF DEVICE (EUT) ...........................................................................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 _______________________________________________________________________________________________ 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement Fig. 1 Fig. 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2A2CU-AB02 _______________________________________________________________________________________________ 1.2. Photo of AC Mains Conducted Emissions Fig. 3