2A2II-ITALK310PoC Radio

Appearance iTALK-310 PoC Radio Quick Guide Please read before using this product iTALKPTT Worldwide Communications https://www.italkptt-international.com/ Items Instructions FCC Warning 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Absorption Rate (SAR) information: This device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. This device was tested for typical body-worn operations with the back of the device kept 10mm from the body without belt-clips, 0mm from the body with the belt-clips, 25mm from the face. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a appropriate separation distance between the user's body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Use only the supplied or an approved antenna. CE Warning 1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 2. The product shall only be connected to a USB interface of version USB2.0 or higher. 3. Adapter shall be installed near the equipment and shall be easily accessible. 4. The operating temperature of the device can’t exceed 40 and shouldn’t be lower than -25. 5. The plug considered as disconnect device of adapter. 6. The device complies with RF specifications when the device used at 5mm from the body without belt-clips, 0mm from the body with the belt-clips, 25mm from the face. 7. Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss. 8. The band 5150-5350MHz indoor use only. Hereby, iTALKPTT Worldwide Communications declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states. Keypad Version No Keypad Version Unpacking and Checking ItemNo.ItemNo. PTT Key Up Side Key Down Side Key Emergency Alarm Key Antenna LED Indicator Channel Knob Power/Volume Knob Microphone Speaker Keypad Battery Latch Connector Cover M6 Connector Type-C Hole for hand strap Belt Clip Battery Battery Contacts SIM Card Cover 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Installing the Battery 1.Align the battery with the rails on the back of the radio, slide upward until the lock position. 2. As shown in the figure below, press down the battery in the direction shown in until the battery latch locks . DisplayKeypad Version) SpeakerNO Keypad Version) Uninstalling the Battery Charging the Battery Method 1By Type-C cable 1. As shown in the figure below, pull the battery latch outward in the direction shown in until the battery pops up and then remove the battery. 1. Plug the adaptor into the power socket. 2. Connect one end of the appropriative Type-C cable to the devices and the other to the USB interface of the adapter. The charging indicator is red, which means that charging starts. 3. The indicator will light green when the device is full charged. Basic Operation Method 2Desktop charger (Optional) 1. Plug the power adapter into a qualified AC power socket. 2. Connect the USB cable to the power adapter, and connect the other end Type-C to the back of the desktop charger. Green indicator light is on. 3. Insert the battery only or together with the radio into the desktop charger. (Power off the radio) 4. Make sure the battery contacts the charging points properly and red indicator light is on. 5. When the indicator light turns from red to green, the battery is full charged. Friendly Reminder: This product is a PoC Radio. The realization of all functions such as calling, programmable keys and menu are related to the management platform settings. For details, please contact your dealer. This document is only for reference, and actual product prevails. Our company reserves the right to the final interpreta…

Text truncated - open the document above for the full version.

Rev 1/26/2023 iTALKPTT Corporation Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Company name: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047, USA Product Name: PoC Radio FCC ID: 2A2II-ITALK310 Model(s): iTALK-310，iTALK-300 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing We, [ iTALKPTT Corporation(“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Yours Sincerely, Name: Warner Mitchell Date: 2023-04-03 Title: General Manager Signature of applicant:

Rev 1/26/2023 iTALKPTT Corporation Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Company name: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047, USA Product Name: PoC Radio FCC ID: 2A2II-ITALK310 Model(s): iTALK-310，iTALK-300 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing We, [iTalkptt Corporation]“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Yours Sincerely, Name: Warner Mitchell Date: 2023-04-03 Title: General Manager Signature of applicant:

Rev 1/26/2023 iTALKPTT Corporation Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-04-03 Ref: Attestation Statements Part 2.911(d)(7) Filing We, [ iTALKPTT Corporation ] (“the applicant”) certifies that, as of the date of the filing of the application, designate our self as U.S. agent for service of process. Designated U.S. Agent Information: Name: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047-1817, USA Contact Person: Warner Mitchell Tel.: (801)203-3389 Email: [email protected] FRN: 0031114887 Sincerely, Applicant signature: Applicant printed name: Warner Mitchell Name: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047-1817, USA Email: [email protected]

iTALKPTT Corporation Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023/04/03 Subject; Request for Confidentiality FCC ID: 2A2II-ITALK310 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM List Tune up procedure Software Security Info In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Warner Mitchell

Model Declaration Letter To who concern We confirm the models iTALK-310 and iTALK-300 are same in circuit board and specification, the same frequency range, antenna, modulation method and RF output power. The difference between these two models is the Screen and Keypad, iTALK-310 has the screen and Keypad, while iTALK-300 doesn’t have. Signature: Contact Person: Warner Mitchell Title: General Manager Company: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047, USA Tel: (801)203-3389 E-Mail: [email protected]

iTALKPTT Corporation Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2023/04/03 SUBJECT: FCC Application for (FCC ID: 2A2II-ITALK310) To Whom It May Concern: We, the undersigned, hereby authorize _ CCIC Southern Testing Co., Ltd. (Chris You)__ at _ Electronic Testing Building, No. 43 Shahe Road, Xili Street, Nanshan District, Shenzhen, Guangdong, China _ on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by __Chris You__ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, ： Signature Contact Person: Warner Mitchell Title: General Manager Company: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047, USA Tel: (801)203-3389 E-Mail: [email protected]

Date: 2023-05-09 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: 2A2II-ITALK310 Dear Sirs: iTALKPTT Corporation requests acceptance of the labeling proposal described below for PoC Radio bearing FCC identifier: 2A2II-ITALK310. The subject cell phone are compact handheld models as shown in figure 1, authorized under 47CFR Part 22, 24, 27, 90 for this mobile services. Figure 1. Because the majority of the cell phone housing is composed of display, speaker, operating controls and a removable battery pack, there is extremely limited space available to attach the required label carrying the FCC identifier. Attaching the label to the battery pack is not acceptable because the battery pack is a removable item. For this reason, iTALKPTT Corporation proposes placing the label carrying the FCC identifier inside the battery compartment as shown in figure 2. Figure 2. The consumer packaging for these models includes the battery pack as a separate item, NOT installed on the radio. As such, the FCC identifier will be readily visible to the user before the battery pack is installed and whenever the battery pack is removed or replaced. In this location, the label will also be protected from physical abuse and remain readable for the anticipated life of the device. The consumer packaging for these models is a "gift box" which does not allow the transceiver to be seen at time of purchase. In order to meet the requirements of 47CFR Part 2.925 (d), iTALKPTT Corporation will add the FCC identifier " 2A2II-ITALK310" to the outside of the consumer "gift box" packaging. Thank you for your attention to this matter. Regards, Signature: Contact Person: Warner Mitchell Title: General Manager Company: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047-1817, USA Tel: (801)203-3389 E-Mail: [email protected]

MAIN ANT WIFI ANT DIV ANT NFC ANT MAIN ANT WIFI ANT DIV ANT NFC ANT

Report No.: SET2023-02489 CCIC-SET/TRF: GJ-EMC-E (2020-01-09) Page 1 of 19 EMC TEST REPORT Report No.: SET2023-02489 Product Name: PoC Radio FCC ID: 2A2II-ITALK310 Model No. : iTALK-310 Series No.: iTALK-300 Applicant: iTALKPTT Corporation Address: 6905 S 1300 E #450, Cottonwood Heights, UT 84047-1817, USA Received Date: 2023.02.14 Dates of Testing: 2023.02.14—2023.03.20 Issued by: CCIC Southern Testing Co., Ltd. Lab Location: Electronic Testing Building, No. 43 Shahe Road, Xili Street, Nanshan District, Shenzhen, Guangdong, China. Tel: 86 755 26627338 Fax: 86 755 26627238 This test report consists of 19 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CCIC-SET. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. Any objections must be raised to CCIC-SET within 15 days since the date when the report is received. It will not be taken into consideration beyond this limit. Report No.: SET2023-02489 CCIC-SET/TRF: GJ-EMC-E (2020-01-09) Page 2 of 19 Test Report Product Name ....................... : PoC Radio Main Model No. ................... : iTALK-310 Series Model No. iTALK-300 Trade name iTALKPTT Brand Name iTALKPTT Applicant ............................... : iTALKPTT Corporation Applicant Address................ : 6905 S 1300 E #450, Cottonwood Heights, UT 84047-1817，USA Manufacturer ........................ : Shenzhen VTU Systems Co., Ltd. Manufacturer Address ......... : 6/F, Building A, Ganghongji High-tech Intelligent Industrial Park, No. 1008, Songbai Road, Nanshan District, Shenzhen 518055, P.R. China Test Standards ...................... : 47 CFR Part 15 Subpart B Test Result ............................ : PASS Tested by ............................. : Ruihong Xie Test Engineer 2023.03.20 Reviewed by ......................... : Chris You Senior Engineer 2023.03.20 Approved by ......................... : 2023.03.20 Hou Tao, Manager Report No.: SET2023-02489 CCIC-SET/TRF: GJ-EMC-E (2020-01-09) Page 3 of 19 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 4 1.1 EUT Description ......................................................................................................................... 4 1.2 Test Standards and Results ........................................................................................................ 5 Facilities and Accreditations ................................................................................................................ 6 1.2.1 Facilities .................................................................................................................................... 6 1.2.2 Test Environment Conditions .................................................................................................... 6 1.2.3 Measurement Uncertainty ......................................................................................................... 6 2. TEST CONDITIONS SETTING .............................................................................................. 7 2.1 Test Peripherals .......................................................................................................................... 7 2.2 Test Mode .................................................................................................................................... 7 2.3 Test Setup and Equipments List ................................................................................................ 8 2.3.1 Conducted Emission ................................................................................................................. 8 2.3.2 Radiated Emission ..................................................................................................................... 9 3. 47 CFR PART 15B REQUIREMENTS .................................................................................. 11 3.1 Conducted Emission ................................................................................................................. 11 3.1.1 Requirement ............................................................................................................................ 11 3.1.2 Test Description ...................................................................................................................... 11 3.1.3 Test Result ............................................................................................................................... 11 3.2 Radiated Emission .................................................................................................................... 14 3.2.1 Requirement ............................................................................................................................ 14 3.2.2 Test Description ...................................................................................................................... 15 3.2.3 Test Result ............................................................................................................................... 15 Change History Issue Date Reason for change 1.0 2023.03.20 First edition Report No.: SET2023-02489 CCIC-SET/TRF: GJ-EMC-E (2020-01-09) Page 4 of 19 1. GENERAL INFORMATION 1.1 EUT Description EUT Name .......................... .: PoC Radio Trade Name.....................: iTALKPTT Brand Name.....................: iTALKPTT Hardware Version............ : IT330_MB_V1.0 Software Version .................. : iTALK310_V1.0 Power supply...................: Adaptor Model No.: JZB110-050200WU I/p: 100-240V～50/60Hz , 500mA O/p: 5.0V2000mA Manufacturer: Shenzhen Jiuzhou Power Technology Co.,Ltd. 1#Battery Brand Name: HUIDAS…

Text truncated - open the document above for the full version.