2A2IVTVSAT25BAntenna

TV SAT 2.5B Installation Manual 1 [날짜] Content 1. Introduction 1.1 Safet y Information 1.2 Com ponents 2. Installation 2.1 Connection of the components 3. Troubleshooting 4. Specification 5. Precaution 2 [날짜] 1. Introduction 1.1 Safety Information Please read the user m anual carefully before you start the installation. If you have already installed sim ilar products, the procedure m ay not be the sam e as for this product. ■ Im proper handling can cause serious dam age to this device. Those responsible m ay also be held responsible for any resulting further dam age to the equipm ent. ■ The antenna is only suitable for m obile use. M ounting on the vehicle is not perm itted. Failure to observe this rule w ill invalidate any w arranty claim . ■ Please check the correct operating voltage of your pow er supply before com m issioning. Please refer to specification in this user m anual for the operating voltage of the device. ■ The control unit m ust not be exposed to dripping w ater, splashing w ater or other liquids. ■ Do not let children play w ith foils or other package m aterials, there is a danger of suffocation. 3 [날짜] 1.2 Com ponents LNB Antenna unit Tripod 10M Coax 1M Coax Cable Antenna unit Hard case Reflector bag Camping Peg Knob Nut LNB + Tripod bag Ca mping Peg bag 1/4” Reflector Nut (2) Power Inserter 4 [날짜] 2. Installation 2.1 Connection of the com ponents Ins tall the control unit and the set-top box is not inside the vehicle in the region of an airbag. M aintain a careful installation of the cable in order to avoid short circuits. Pay attention also to existing cables. Connect the antenna as show n in the illustration below : Fix legs on the ground with tent pegs. 1 Fix legs on the ground with tent pegs. 2 3 Put the body on tripod and fasten the knob. 4 4 5 Connect Main LNB and Side LNB connectors. Put the antenna dish on the dish bracket and fix with bolt and nut at marked area 6 Put it on the star and put the lobe 5 [날짜] 7 Connect to the connecting diagram. 9 Turn on the set-top box. Antenna starts scanning satellites in full EL/AZ range (It takes about 5~10 min for full scanning). 10 11 Antenna starts scanning satellites in full EL/AZ range (It takes about 5~10 min for full scanning). Tighten the lockingknob in order to secure the pointing to target satellite. The light will continue when it is locked enough 12 Turn on the power adapter. 8 6 [날짜] - Connection Chart – - 3. Troubleshooting N o satellite signal O bjects such as trees, bridges and large houses located at the satellite’s angle of incidence cause the signal to be lost. If the satellite signal is lost due to severe w eather conditions, the current program of the TV or receiver w ill be interrupted (the picture w ill pixelate, freeze or disappear). W hen the weather conditions allo w good reception again, the TV picture w ill be restored. Is there dirt on the antenna ? H eavy dirt on the housing can cause reception problem s. Is everything correctly connected and sw itched on ? M ake sure that the TV and the receiver are connected correctly and that the receiver I correctly set for satellite reception. Are all cables connected correctly and the connections crew tightly onto the coaxial cable ? Also check the coaxial cable for kinks. 7 [날짜] Footprint of the satellite Satellite are in fixed posi tions above the equator in orbit. In order to receive the TV signals, the receiving location m ust be within the footprint. In the peripheral areas of the footprint, reception interference m ay occur. Satellite frequency of a TV channel w as changed TV stations change their fre quency sporadically, w hich then no longer m atches the frequency in the receiver. Ask for the current frequency of the channel. The firm w are of the control unit is outdated If transponders on the satellite are changed, the antenna m ay no longer be able to find the satellite. U pdate the firm w are of the control unit to get the latest transponder inform ation. The m obile app does not connect to control unit M ake sure the Bluetooth® on your mobile device is switched on and that you are in the direct vicinity of the control unit (max. 10 metres). 8 [날짜] 4. Specifications Model TVSAT 2.5B Antenna Type Parabola Frequency Dish net Weight 3.8 kg Antenna Gain Dish net Polarization CP Stabilized Type 2-Axis Step motor AZ Range Endless EL Range 10° ~ 60° SK Range -40° ~ 50° Temp -20° ~ 70° Power 24V dc, 1.3A 1.FCC Compliance Statement(Part 15.19 (3)) This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.FCC Interference Statement(Part 15.105) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 3.FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Telecomunication BLE 9 [날짜] 5. Precaution 1. Keep this ‘Manual’ for your safe usage. 2. Please be aware all information of this product. And operate the TVSAT in proper way. 3. Please handle the TVSAT product carefully. Do not drop the TVSAT and avoid excessive shock or vibration …

Text truncated - open the document above for the full version.

WIWORLD Co., Ltd. 32-4 Techno 7 Street, Yusung Gu, Daejeon City, Korea Date: June 29, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Chloe Lee/ Deputy General Manager of KCTL Inc. and hereafter referred to as KCTL to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Chloe Lee/ Deputy General Manager of KCTL Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KCTL as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Oh Jonghyun/ General manager WIWORLD Co., Ltd.

WIWORLD Co., Ltd. 32-4 Techno 7 Street, Yusung Gu, Daejeon City, Korea CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 June 29, 2021 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, WIWORLD Co., Ltd. requests confidentiality for the following products: FCC ID Number Product Title/Model 2A2IVTVSAT25B Antenna / TV SAT2.5B Th e following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request -. Schematics -. Block Diagram -. Operational Description -. Antenna specification We also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. Short-Term Confidential Request -. External Photos -. Internal Photos -. Test set-up photo -. User Manual If you have any questions, please feel free to contact me at the address shown below. S incerely, Oh Jonghyun/ General manager 32-4 Techno 7 Street, Yusung Gu, Daejeon City, Korea +82-42-630-0691

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval External photos of EUT Whole http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval EUT(TV SAT 2.5B) http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Adapter

1. Label Location 2. Label Drawing Label Information Label position 47mm WIWORLD Co., Ltd. Antenna MODEL: TV SAT2.5B FCC ID : 2A2IVTVSAT25B S/N:WI-U100001 Made in KOREA 23m * The front of device

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Internal photos of EUT Chip Antenna http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval * RF Exposure 1. Regulation Regulation This document is prepared to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC rules and Regulations. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is listed in Table 1-1. According to FCC §1.1310: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). Table 1 – Limits for Maximum Permissible Exposure (MPE) Frequency Range (㎒) Electric Field Strength [V/m] Magnetic Field Strength [A/m] Power Density [㎽/㎠] Averaging Time [minute] (A) Limits for Occupational / Controlled Exposure 0.3 ~ 3.0 614 1.63 *100 6 3.0 ~ 30 1842/f 4.89/f *900/f 2 6 30 ~ 300 61.4 0.163 1.0 6 300 ~ 1 500 / / f/300 6 1 500 ~ 15 000 / / 5 6 (B) Limits for General Population / Uncontrolled Exposure 0.3 ~ 1.34 614 1.63 *100 30 1.34 ~ 30 824/f 2.19/f *180/f 2 30 30 ~ 300 27.5 0.073 0.2 30 300 ~ 1 500 / / f/1 500 30 1 500 ~ 15 000 / / 1.0 30 f=frequency in ㎒, *= plane-wave equivalent power density Per the guidance of KDB 680106, the E-field and H-field limits shown in the table above are extended down to 100 ㎑ in Appendix C): 1) For test separation distances > 50 ㎜ and < 200 ㎜, the power threshold at the corresponding test separation distance at 100 ㎒ in step b) is multiplied by [1 + log(100/f(㎒))] 2) For test separation distances ≤ 50 ㎜, the power threshold determined by the equation in c) 1) for 50 ㎜ and 100 ㎒ is multiplied by ½ 3) SAR measurement procedures are not established below 100 ㎒. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any SAR test results below 100 ㎒ to be acceptable. http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval 2. Result MPE (Maximum Permissive Exposure) Prediction Predication of MPE limit at a given distance: Equation from page 18 of OET Bulletin 65, Edition 97-01  SPGRRPGS4 4 2  S = power density [㎽/㎠] P = Power input to antenna [㎽] G = Power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna [㎝] RF Exposure Compliance Issue The information should be included in the user’s manual: This appliance and its antenna must not be co-located or operation is conjunction with any other antenna or transmitter. A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Note. 1. The power density P d (5th column) at a distance of 20 ㎝ calculated from the friis transmission Formula is far below the limit of 1 ㎽/㎠. 2. Unequal antenna gains, with equal transmit powers. For antenna gains given by G1, G2, ..., GN ㏈i (i) If transmit signals are correlated, then Directional gain = 10 log[(10G 1 /20 + 10G 2 /20 + ... + 10G N /20)2/NANT] ㏈ i [Note the “20”s in the denominator of each exponent and the square of the sum of terms; the object is to combine the signal levels coherently.] http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Calculation Result of RF Exposure Mode Frequency [㎒] Max Tune-up Power [㏈m] Max Tune-up Power [㎽] Ant Gain [㏈i] Power density at 20 ㎝ [㎽/㎠] Limit [㎽/㎠] GFSK 2 480 -14.00 0.04 2.30 0.000 01 1.00

verify No.076636005418 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0153 Page (2) of (33) KCTL-TIR001-003/5 KP21-01442 REPORT REVISION HISTORY Date Revision Page No 2021-07-06 Originally issued - This report shall not be reproduced except in full, without the written approval of KCTL Inc. This document may be altered or revised by KCTL Inc. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KCTL Inc. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. General remarks for test reports Statement concerning the uncertainty of the measurement systems used for the tests (may be required by the product standard or client) Internal procedure used for type testing through which traceability of the measuring uncertainty has been established: Procedure number, issue date and title: Calculations leading to the reported values are on file with the testing laboratory that conducted the testing. Statement not required by the standard or client used for type testing KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0153 Page (3) of (33) KCTL-TIR001-003/5 KP21-01442 CONTENTS 1. General information ...................................................................................................... 4 2. Device information ........................................................................................................ 4 2.1. Accessory information ............................................................................................ 4 2.2. Frequency/channel operations ................................................................................ 5 2.3. Duty Cycle Factor ................................................................................................... 5 3. Antenna requirement .................................................................................................... 6 4. Summary of tests .......................................................................................................... 7 5. Measurement uncertainty ............................................................................................. 8 6. Measurement results explanation example .................................................................. 9 7. Test results ................................................................................................................. 10 7.1. Maximum peak output power ................................................................................ 10 7.2. Peak Power Spectral Density ............................................................................... 13 7.3. 6 ㏈ Bandwidth(DTS Channel Bandwidth) .......................................................... 15 7.4. Spurious Emission, Band Edge and Restricted bands .......................................... 17 7.5. Conducted Spurious Emission .............................................................................. 29 7.6. AC Conducted emission ....................................................................................... 31 8. Measurement equipment ............................................................................................ 33 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0153 Page (4) of (33) KCTL-TIR001-003/5 KP21-01442 1. General information Client : WIWORLD Co., Ltd. Address : 32-4 Techno 7 Street, Yusung Gu, Daejeon City, Korea Manufacturer : WIWORLD Co., Ltd. Address : 32-4 Techno 7 Street, Yusung Gu, Daejeon City, Korea Laboratory : KCTL Inc. Address : 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea Accreditations : FCC Site Designation No: KR0040, FCC Site Registration No: 687132 VCCI Registration No. : R-20080, G-20078, C-20059, T-20056 CAB Identifier: KR0040, ISED Number: 8035A KOLAS No.: KT231 2. Device information Equipment under test : Antenna Model : TV SAT 2.5B Modulation technique : GFSK (Bluetooth Low Energy) Number of channels : 40 ch (Bluetooth Low Energy) Frequency range : 2 402 ㎒ ~ 2 480 ㎒ (Bluetooth Low Energy) Power source : DC 24 V Antenna specification : Chip Antenna Antenna gain : 2.3 ㏈i Software version : WI2.5B_sw 2.1 Hardware version : WI2.5B_hw 1.0 Operation temperature : -20 °C ~ 70 °C 2.1. Accessory information Equipment Manufacturer Model Serial No. Power source AC/DC Adapter Shenzhenshi Zhenhuan Electronic Co., Ltd. ZF120A-2402500 - Input : AC 100~240 V, 2.0 A Output : DC 24 V, 2.5 A KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0153 Page (5) of (33) KCTL-TIR001-003/5 KP21-01442 2.2. Frequency/channel operations This device contains the following capabilities: Bluetooth Low Energy Ch. Frequency (㎒) 00 2 402 . . . . 19 2 440 . . . . 39 2 480 Table 2.2.1. Bluetooth Low Energy 2.3. Duty Cycle Factor Test mode Period (ms) On time (ms) Duty cycle Duty Cycle Factor (dB) (Linear) (%) 1M Bits/s, 37 Packet 0.625 0.395 0.632 4 63.24 1.99 Notes. 1. Duty cycle (Linear) = Ton time / Period 2. DCF(Duty cycle factor) = 10log(1/duty cycle) 1M Bits/s, 37 Packet KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0153 Page (6) of (33) KCTL-TIR001-003/5 KP21-01442 3. Antenna requirement Requirement of FCC part section 15.203 An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently att…

Text truncated - open the document above for the full version.

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Test setup photos - Below 30 ㎒ (9 ㎑ ~ 30 ㎒) - Below 1 ㎓ (30 ㎒ ~ 1 ㎓) http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval - Above 1 ㎓ (1 ㎓ ~ 18 ㎓) - Above 18 ㎓ (18 ㎓ ~ 26.5 ㎓) http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Conducted Emission