2A2R7AF-BH009Surround wireless earbuds

SURROUND WIRELESS EARBUDS USER MANUAL AF-BH009 EN SAFETY INSTRUCTIONS Please read the instructions thoroughly before using this product and retain it for future reference. •Do not expose the earbuds to liquids, moisture or humidity. •Do not use abrasive cleaning solvents to clean it. •Remove and clean the ear tips regularly. •Do not expose the earbuds to extremely high or low temperatures as this may damage the battery or deform the plastic parts. •Do not throw the earbuds in a fire or dispose casually. •Do not try to disassemble the earbuds. No user serviceable parts inside. •Try not to drop the earbuds or apply any force to the earbuds. •Charge the earbuds from 5V USB ports such as phone chargers or computers. •Do not use earbuds in thunderstorm to avoid malfunction or electric shock. •Never listen to music at high volumes, or you may permanently damage your hearing. •Nev er wear earbuds while riding, driving or walking in traffic. Always stay aware of your surroundings. •Always ask a professional technician or authorized personnel for repair. PACKAGE CONTENTS 1*Surround Wireless Earbuds 1*Type-C Charging Cable 6*Ear Tips 2*Ear Hooks 1*User Manual KNOWING YOUR EARBUDS JP 安全上の注意 製品をご使用頂く前にユーザーマニュアルを全てお読みください。また、今後参照するために、 マニュアルは保管ください。 •イヤホンは、液体、蒸気、湿度からは避けてください。 •研磨剤の入った洗剤は使わないでください。 •イヤーチップは、定期的に外してクリーニングしてください。 •イヤホンは、極度な温度は避けてください。バッテリーの損傷やプラスチック部分の変形 を引き起こすことがあります。 •イヤホンを火に入れたり、安易に処分したりしないでください。 •イヤホンを分館しないでください。お客様自身で修理可能な内部パーツはありません。 •イヤホンを落下させたり、圧力を加えたりしないでください。 •イヤホンは、携帯電話やコンピューターの5VのUSBポート から充電してください。 •暴風雨の中でのイヤホンの使用はおやめください。故障や電気ショックを引き起こす可 能性があります。 •音量を高くして音楽を聴くことは避けてください。聴力を失う可能性があります。 •車の運転中、自電車やバイクの走行中、または歩行中のイヤホンの使用はおやめくださ い。常に周囲の状況に気をつけてください。 •修理が必要な場合は、専門技術者または認定資格保有者に依頼ください。 パッケージ内容 サラウンドワイヤレスイヤホン １ タイプC充電ケーブル １ イヤーチップ６ イヤーフック２ ユーザーマニュアル１ イヤホンを知る アクセサリー イヤーチップ (１組は装着済) イヤーフック イヤホンの設定 充電 初めての場合は、イヤホンをフル充電してからご使用することをお勧めします。 1.充電ポートのシリコンカバーを外します。 2.タイプCケーブルを充電ポートに差し込みます。 3.電源に接続すると自動的に充電がスタートします。 電源オン/オフ オン イヤホンを離すと電源が入ります。 オ フ イヤホンをくっ付けると電源が切れます。 インジケーター 充電 赤く点灯 フル充電 白く点灯 イヤホンを使う Bluetoothの注意事項 •接続する二つの機器を近づけて置き、他のBluetooth機器の電源をオフにします。 •環境状況によりBluetoothの有効範囲が異なります。二つの機器の間に障害になるもの（壁 やフェンスなど）があると有効範囲が狭まる可能性があります。 Bluetoothペアリング 1.イヤホンの電源をオンにすると、自動的にペアリングモードになります。 2.ご利用の機器のBluetooth機能を有効にし、 近くの機器を検索します。 3.検索結果の中の“Alfox BH009”を選択し、接続します。 状 況インジケーター 白と赤が交互に点滅 ペアリング 白 い点滅 接続済み 注意: •イヤホンの電源をオンにする度に、最後に接続した機器が有効範囲にあると自動的に接続 します。 コントロールと機能 前に戻る Vol –を２秒間長押し 次に進む Vol +を２秒間長押し 音量を下げる Volを押す- 音量を上げる Vol +を押す 再生/一時停止 MFBボタンを押す 応答 MFBボタンを押す 切断 MFBボタンを押す (通話の間) 拒否 MFBを２秒間長押し 音声アシスタント MFBを３回押す ゲームモード MFBを２秒間長押し (ゲームの間) イヤホンのリセット イヤホンの接続や使用中にトラブルが発生した場合は、イヤホンをリセットしてください。 1.リセットする前に、必ずご利用の機器がフル充電されているか確認ください、 2.２つの音量ボタンを同時に５秒間長押しすると、インジケーターが3度点滅します。 3.その後、再度接続の手順に従い再接続を行ってください。 注意: •他のBluetooth機器と接続するには、接続していた機器のBluetooth機能を一度無効にし、 新しい機器と接続します。その後、前の機器のBluetoothを有効にしてください。 クリーニングとメンテナンス 乾いた柔らかい綿棒のようなもので拭き取ってください。ノズルに何もいれな いでください。 乾いた柔らかい綿棒のようなもので拭き取ってください。 イヤーチップは取り外し、弱酸性などのマイルドな洗剤と水で洗い流してくだ さい。イヤホンに装着する前に、必ず完全に乾かしてください。. イヤーチップとイヤーフックは定期的に掃除してください。 尖ったものは傷がつかないよう近づけないでください。 長期間使用しない場合は、湿気のない日陰の場所で保管ください。 洗剤や化学薬品を使ってのクリーニングは絶対に避けてください。 音量–ボタン 音量+ボタン MFBボタン イヤーフック イヤーチップ マイク Accessories Ear ps (One pair equipped) Ear hook SETTING UP YOUR EARBUDS Charging We highly recommend that you fully charge the earbuds before using them for the first time. 1. Unplug the silicone cover on the charging port. 2. Plug in the Type-C cable to the charging port. 3. Connect to power supply and it will start charging automatically. Power ON/OFF USING YOUR EARBUDS Bluetooth Caution •Place the two devices to be connected close to each other and turn off other Bluetooth devices. •The maximum effective Bluetooth range may vary with the environmental circumstances. Obstacles (walls, fences, etc.) between the two devices may shorten the effective range. Bluetooth Pairing 1. Power on the earbuds, it will enter pairing mode automatically. 2. Turn on the Bluetooth function on your device and search for nearby devices. 3. Find “Alfox BH009” in the search results, tap to connect. Status Indicator Blinking White/Red Alternately ON Separate the earbuds to power on. OFF Placeearbudstogetherto power off. Indicator Charging Solid Red Fully ChargedSolid White 此线要删 delete this line Legen Sie sie an einen trockenen und schattigen Ort, wenn sie für lange Zeit nicht benutzt werden. NICHT mit Reinigungsmitteln oder Chemikalien reinigen. WEEE COMPLIANCE Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) Thi s marking on the product, accessories or literature indicates that the product and its electronic accessorie s s hould not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of whereand how they can take these items for environmentally safe recyc ling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Rev_1.0 Email: [email protected] Lautstärke erhöhen Drücken Sie "Lautstärke +" Wiedergabe / Pause Drücken Sie die MFB-Taste Anruf annehmen Drücken Sie die MFB-Taste Auflegen Drücken Sie die MFB-Taste (während des Telefonats) Anruf ablehnen Halten Sie die MFB- Taste 2s gedrückt Sprachassistent Drücken Sie die MFB-Taste dreimal Gaming-Modus Halten Sie die MFB- Taste 2s gedrückt (während des Spielens) Zurücksetzen Ihrer Ohrhörer Setzen Sie die Ohrhörer zurück, wenn Sie Probleme beim Verbinden oder Verwenden der Ohrhörer haben. 1.Stellen Sie vor dem Zurücksetzen sicher, dass Ihr Gerät vollständig aufgel…

Text truncated - open the document above for the full version.

2.4GHz 2012 Chip Antenna:RANT2012F245C02 Application: WLAN, 802.11b/g, Bluetooth, etc... Features SMD, high reliability, ultra Impact, Omni-directional... Part number RANT 2012 F245 (1)(2) (3) (4) C02 (5) (1)Product TypeChip Antenna (2)Size Code2.0x1.2mm (3)Type CodeF (5)Frequency2.45GHz (6)Internal codeC02 Electrical Specification Working Frequency Range2400 ~2484 MHz Peak Gain1.06 dBi (Typ.) Impedance50 Ohm Return loss10 dB ( Min) PolarizationLinear Azimuth BeamwidthOmni-directional Operation Temperature(°C)-40 ~85°C The specification is defined on EVB. Dimension and Terminal Configuration No.Terminal Name 1Feeding/GNG 2GND/Feeding P.S : Top & down and left & right side are symmetrical, No direction Dimension (mm) L2.05+-0.15 W1.20+-0.15 T0.50+-0.10 A0.20+-0.10 RAIN International Technology Co., Ltd. 2.4GHz 2012 Chip Antenna:RANT2012F245C02 eturn Loss 1 Evaluation Board Reference PCB DimensionAntenna Layout Reference Unit :mmUnit :mm Electrical Characteristics Return Loss & Radiation R Trc2dB Mag 10 dB / Ref 0 dB Invisible1 Trc3dB Mag 10 dB / Ref 0 dB Cal int Offs Frequency S11 (dB) (MHz) 2400-10.78 2442-24.81 2484-10.24 S11 M 1 M 2 2.4000 2.4420 00GHz 00GHz -10.77 -24.81 6 dB 2 dB 41 31 21 11 0 M 32.484000 GHz-10.243 dB M 1 M3 -9 -19 M 2 -29 -39 Ch1 Start 2 GHzPwr 0 dBmStop 3GHz Radiation RAIN International Technology Co., Ltd. 2.4GHz 2012 Chip Antenna:RANT2012F245C02 Taping Specifications Reel and Taping Specification Reel Specification TYPESIZEA ψ B ψ C ψ D W ψ M 20127”5K/Reel2.0±0.513.5±1.021±1.060±1.011.5±2.0178±2.0 Tapping Specification PackagingTypeABWEFGHTψDP Paper Type32161.90±0.203.50±0.208.0±0.201.75±0.103.5±0.054.0±0.102.0±0.050.75±0.10 +0.10 1.50 -0 4.0±0.1 RAIN International Technology Co., Ltd. 2.4GHz 2012 Chip Antenna:RANT2012F245C02 Reliability Table Test ItemProcedure Requirements Ceramic Type Remark (Reference) Electrical Characterization Fulfill the electrical specification User Spec. Thermal Shock 1. Preconditioning: 50 ± 10 °C / 1 hr , then keep for 24 ± 1 hrs at room temp. 2. Initial measure: Spec: refer Initialspec. 3. Rapid change of temperature test: -30 °C to +85 °C ; 100 cycles; 15 minutes at Lower category temperature; 15 minutes at Upper category temperature. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 107 Temperature Cycling 1. Initial measure: Spec: refer Initialspec. 2. 100 Cycles (-30 °C to +85 °C ), Soak Mode=1 (2Cycle/hours). 3. Measurement at 24 ± 2Hours after testcondition. No Visible Damage. Fulfill the electrical specification. JESD22 JA104 High Temperature Exposure 1. Initial measure: Spec: refer Initialspec. 2. Unpowered; 500hours @ T=+85 °C . 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Low Temperature Storage 1. Initial measure: Spec: refer Initialspec. 2. Unpowered: 500hours @ T=-30 °C . 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Solderability (SMD Bottom Side) Dipping method: a. Temperature: 235 ±5°C b. Dipping time: 3 ±0.5s The solder should cover over 95% of the critical area of bottom side. IEC 60384-21/22 4.10 Soldering Heat Resistance (RSH) Preheating temperature: 150 ± 10°C. Preheating time: 1~2 min. Solder temperature: 260 ± 5°C. Dipping time: 5 ± 0.5s No Visible Damage.IEC 60384-21/22 4.10 Vibration5g's for 20 min., 12 cycles each of 3 orientations Note: Use 8"X5" PCB .031" thick 7 secure points on, one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10-2000 Hz. No Visible Damage.MIL-STD-202 Method 204 Mechanical Shock Three shocks in each direction shall be applied along the three mutually perpendicular axes of the test specimen (18 shocks) Peak value: 1,500g’s Duration: 0.5ms Velocity change: 15.4 ft/s Waveform: Half-sine No Visible Damage.MIL-STD-202 Method 213 Humidity Bias 1. Humidity: 85% R.H., Temperature:85 ± 2 °C. 2. Time: 500 ± 24hours. 3. Measurement at 24 ± 2hrs after testcondition. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 Method 106 RAIN International Technology Co., Ltd. 2.4GHz 2012 Chip Antenna:RANT2012F245C02 Board Flex (SMD) 1. Mounting method: IR-Reflow. PCB Size (L:100 × W:40 × T:1.6mm) 2. Apply the load in direction of the arrow until bending reaches 2 mm. No Visible Damage.AEC-Q200 005 AdhesionForce of 1.8Kg for 60 seconds.No Visible Damage Magnification of 20X or greater may be employed for inspection of the mechanical integrity of the device body terminals and body/terminal junction. AEC-Q200 006 Physical Dimension Any applicable method using x10 magnification, micrometers, calipers, gauges, contour projectors, or other measuring equipment, capable of determining the actual specimen dimensions. In accordance with specification. JESD22 JB100 Revision History RevisionDateContent 12015/8/20New issue 22017/4/20Update detail dimension on antenna layout 32018/2/1Part number and coding rule updated RAIN International Technology Co., Ltd.

Shenzhen Danya Technology Co., Ltd. Room 3323, Building C, Galaxy World Phase II, Minle Community, Minzhi Street, Longhua District, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Sep. 02, 2022 Subject; Request for Confidentiality FCC ID: 2A2R7AF-BH009 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Bobby Zou Title: Approbation Manager

Report No.: AGC13454220825AP02 Page 1 of 4 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC13454220825AP02 Page 2 of 4 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC13454220825AP02 Page 3 of 4 LEFT VIEW OF EUT RIGHT VIEW OF EUT Report No.: AGC13454220825AP02 Page 4 of 4 PORT VIEW OF EUT ****************************************End of Report****************************************

FCC ID Label Location Made in China 204-B00726

Report No.: AGC13454220825AP02 Page 1 of 3 INTERNAL PHOTOS OPEN VIEW OF EUT BATTERY VIEW OF EUT Report No.: AGC13454220825AP02 Page 2 of 3 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC13454220825AP02 Page 3 of 3 ANTENNA CLOSE-UP PHOTO-1 ****************************************End of Report**************************************** BT Antenna

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description Surround wireless earbuds Model Name AF-BH009 Series Model TT-BH113 FCC ID 2A2R7AF-BH009 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v06 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION P t =5.742dBm=3.75mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.247. The result for RF exposure evaluation SAR=(3.75mW /5mm) .[√2.480GHz)]=1.18<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 67 FCC Test Report Report No.: AGC13454220825FE03 FCC ID : 2A2R7AF-BH009 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Surround wireless earbuds BRAND NAME : ALFOX, TAOTRONICS MODEL NAME : AF-BH009, TT-BH113 APPLICANT : Shenzhen Danya Technology Co., Ltd. DATE OF ISSUE : Sep. 01, 2022 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC13454220825FE03 Page 2 of 67 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 01, 2022 Valid Initial Release Report No.: AGC13454220825FE03 Page 3 of 67 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH .............................................................................................................. 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ......................................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ......................................................... 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................... 8 2.7. TEST METHODOLOGY ............................................................................................................................. 8 2.8. SPECIAL ACCESSORIES ......................................................................................................................... 8 2.9. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.10. ANTENNA REQUIREMENT..................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................. 11 5.1. CONFIGURATION OF EUT SYSTEM ....................................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM ............................................................................................... 11 5.3. SUMMARY OF TEST RESULTS ............................................................................................................... 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE ............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. 20DB BANDWIDTH ........................................................................................................................................ 19 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 19 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 20 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 25 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 25 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 25 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 25 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 25 Report No.: AGC13454220825FE03 Page 4 of 67 10. RADIATED EMISSION ................................................................................................................................. 46 10.1. MEASUREMENT PROCEDURE ........................................................................................................... 46 10.2. TEST SETUP ......................................................................................................................................... 48 10.3. LIMITS AND MEASUREMENT RESULT ............................................................................................... 49 10.4. TEST RESULT........................................................................................................................................ 49 11. NUMBER OF HOPPING FREQUENCY .................................…

Text truncated - open the document above for the full version.

Report No.: AGC13454220825FE03 Page 62 of 67 Test_Graph_BR_HOP_ANT1_NA_1Mbps_2441_Number of Busrt Test_Graph_BR_HOP_ANT1_NA_1Mbps_2441_Time per Burst Report No.: AGC13454220825FE03 Page 63 of 67 Test_Graph_BR_HOP_ANT1_NA_1Mbps_2480_Number of Busrt Test_Graph_BR_HOP_ANT1_NA_1Mbps_2480_Time per Burst Report No.: AGC13454220825FE03 Page 64 of 67 13. FREQUENCY SEPARATION 13.1. MEASUREMENT PROCEDURE The EUT shall have its hopping function enabled. Use the following spectrum analyzer settings: 1. Span: Wide enough to capture the peaks of two adjacent channels. 2. RBW: Start with the RBW set to approximately 30% of the channel spacing; adjust as necessary to best identify the center of each individual channel. 3. Video (or average) bandwidth (VBW) ≥ RBW. 4. Sweep: Auto. e) Detector function: Peak. f) Trace: Max hold. g) Allow the trace to stabilize. Use the marker-delta function to determine the separation between the peaks of the adjacent channels. 13.2. TEST SETUP (BLOCK DIAGRAM OF CONFIGURATION) Same as described in section 6.2 13.3. MEASUREMENT EQUIPMENT USED The same as described in section 6.3 13.4. LIMITS AND MEASUREMENT RESULT Test Data of Frequency Separation Test Mode Channel Separation (MHz) Limits Pass or Fail GFSK Hopping 0.997 >= 2/3 -20dB BW Pass Test Graphs of Number of Hopping Frequency Test_Graph_BR_HOP_ANT1_NA_1Mbps_Hopping Separation Note: The GFSK modulation is the worst case and recorded in the report. Report No.: AGC13454220825FE03 Page 65 of 67 14. LINE CONDUCTED EMISSION TEST 14.1. LIMITS OF LINE CONDUCTED EMISSION TEST Frequency Maximum RF Line Voltage Q.P. (dBμV) Average (dBμV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. 14.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units Report No.: AGC13454220825FE03 Page 66 of 67 14.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipment received AC120V/60Hz power from a LISN, if any. 5. The EUT received DC 5V power from adapter which received AC120V/60Hz power from a LISN. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 14.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less – 2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page. 14.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST N/A Note: The BT function cannot transmit when charging. Report No.: AGC13454220825FE03 Page 67 of 67 APPENDIX A: PHOTOGRAPHS OF TEST SETUP Refer to the Report No.: AGC13454220825AP01 APPENDIX B: PHOTOGRAPHS OF EUT Refer to the Report No.: AGC13454220825AP02 ----END OF REPORT---- Conditions of Issuance of Test Reports 1. All samples and goods are accepted by the Attestation of Global Compliance (Shenzhen) Co., Ltd. (the “Company”) solely for testing and reporting in accordance with the following terms and conditions. The company provides its services on the basis that such terms and conditions constitute express agreement between the company and any person, firm or company requesting its services (the “Clients”). 2. Any report issued by Company as a result of this application for testing services (the “Report”) shall be issued in confidence to the Clients and the Report will be strictly treated as such by the Company. It may not be reproduced either in its entirety or in part and it may not be used for advertising or other unauthorized purposes without the written consent of the Company. The Clients to whom the Report is issued may, however, show or send it, or a certified copy thereof prepared by the Company to its customer, supplier or other persons directly concerned. The Company will not, without the consent of the Clients, enter into any discussion or correspondence with any third party concerning the contents of the Report, unless required by the relevant governmental authorities, laws or court orders. 3.The Company shall not be called or be liable to be called to give evidence or testim…

Text truncated - open the document above for the full version.

Report No.: AGC13454220825AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC13454220825AP01 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************