2A2VW-C6LWirelessCam Lite

aosu Wireless Security Camera ＿ Quick Start Guide G United States:+ 1-866-905-9950 Mon-Fri 9AM-5PM (PST} United Kingdom: +44-20-3885-0830 Mon-Fri 9AM-5PM (GMT} Germany: +49-32-221094692 Mon-Fri 9AM-5PM (CET} Japan: +81-SO-S840-2601 Mon-Fri 9AM-5PM (JST) e [email protected]。www.aosulife.comO @aosulife AOSUCare Hi Customer Thank you for choosing AOSU security products. We have always put OU「customersfirst and foremost. There are 3 things you should know before using this product: 1. Micro SD Card If you don't have a Micro SD Card available at home now and don't want to spend extra time choosing one, please contact us directly. TIP: the Micro SD Card gotta be formated after inserting it up. 2. Select 2.4G Wi-Fi The product only supports 2.4G Wi-Fi, please select 2.4G Wi-Fi when setting up the app. 3. Select installation location. Please use your mobile phone to test the coverage of the home Wi-Fi signal at the planned installation position before installation , so that the product can receive a bette「signal. Get all the tutorial videos of using product including but no limit to set up the app, installation and format micro sd card, visit: aosulife.com 」oin"AOSUCare" today as three ways below to get all of your problems solved by one-on-one live chat and phone service tech support. @ United States: +1-866-905-9950 Mon-Fri 9AM-5PM (PST) United Kingdom: +44-20-3885-0830 Mon-Fri 9AM-5PM (GMT) Ge『many:+49-32-221094692 Mon-Fri 9AM-5PM (CET) Japan: +81-50-5840-2601 Mon-Fri 9AM-5PM (」ST) @ www.aosulife.com o @aosulife e [email protected] TABLE OF CONTENTS 01 What's Included POl 02 Product Overview P02 03 Setting Up the System P03 04 Mounting the Camera P04-07 05 Notice P08-P09 06 Customer Service PlO What's Included 产 [1111111111 11111111•0� 血 ， J ｀ [11\\\\\\\\\\\\\\\\>0 � 吐 年 止心 它 ， [11\\\\\\\\\\\\\\IISI]=�丘) c,,,,,,,,,,,,,,,,,,.o� 立�王) Camera Screw Pack USB-C Charging Cable 。 曰 三 Position Sticker Security Sticker Quick Start Guide — 01 — Product Overview Lens Infrared Leds PIR Motion Sensor Microphone Base bracket Spotlights Power Type七port SD Card Slot Reset button CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and device could be damaged. SD Card Port: Support Micro SD Card for local storage (Max 512GB). Reset button: Press and hold the button for 3 seconds, and then the device will be ready to be connected. Card capacity requirements: 8-512GB. Read and write speed requirements: class1 O level. File format: FAT32. — 02 — Setting Up the System Download the Aosu App from the App Store (iOS devices) or Google Play (Android devices). 1霆， Sign up for an Aosu App account, then follow the onscreen instructions to complete the setup. — 03 — Mounting the Camera Find a Good Mounting Spot To find a spot to mount Camera, you need to test wireless signal strength. CD Open the Aosu A pp, go to Camera Settings> Mounting Guide. @To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera. ®Move the camera as close to the Wi-Fi Router as possible to get a better signal. ,,., "''夸售一 Camara1 X Test Signal T扯""叩飘,_出心心心""'"'心"'� 仰-�,.,-,.,鲁�·咖,,w心中配""" "'""""''"'"心.,心.,_,..,,心l 会 G,ea< ..,_,,�� 氓s,飞叩h O沁Q盯M<k>也闷··-··-· — 04 — Select Height and Location Hang AOSUCam 7-1 Oft (78-118 inches) above the ground. This height maximizes the detection range of the motion sensor of AOSUCam. Avoid placing AOSUCam under direct sunlight. Camera field of view I Up to 32ft I — 05 — Test the Wi-Fi signal at installation position Use cell phone to test Wi-Fi signal quality at the installation position before installing camera, make sure the Wi-Fi router can provide good Wi-Fi signal. — 06 — Installation 1. Drilling according to position sticker, drill bit: 15/64"(6 mm). 2. Insert the plugs. 3. Tighten the screws. What is required: Sticker Wall — 07 — Screw Camera Notice FCC Statement This device complies with Part 15 of the FCC Rules. Operation is sub」ectto the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and f o und to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency ener窃and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communi­ cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the f o llowing measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/ TV technician for help. FCC Radio Frequency Exposure Statement The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm. — 08 — (E T his product complies with the radio interference requirements of the European Community. Declaration of Conformity Hereby, Aosu declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformit y , visit…

Text truncated - open the document above for the full version.

Shenzhen Zhiling Technology Co., Ltd Agent Authorization Company: Shenzhen Zhiling Technology Co., Ltd Address: Room 201, Building A, No.1 Qianwan Road, Qianhai Shenzhen-Hong Kong Cooperation Zone, Shenzhen, Guangdong, China Product Name: WirelessCam Lite Trade Mark: AOSU Model Number(s): C6L,C6E,C6P,C6S,DC6L,DC6E,DC6P,DC6S FCC ID: 2A2VW-C6L We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022-10-26 Name: Wes Yan Title: PM Company: Shenzhen Zhiling Technology Co., Ltd

Shenzhen Zhiling Technology Co., Ltd Add: Room 201, Building A, No.1 Qianwan Road, Qianhai Shenzhen-Hong Kong Cooperation Zone, Shenzhen, Guangdong, China Tel: 13434704210 Date: 2022-10-26 Dear Sir/Madam, We, Shenzhen Zhiling Technology Co., Ltd Hereby declares the following statement , PCB board, circuit, structure and internal of these model(s) are the same, Only model name is different for these model: P Product Name: WirelessCam Lite Trade Mark: AOSU Model Number(s): C6L,C6E,C6P,C6S,DC6L,DC6E,DC6P,DC6S FCC ID: 2A2VW-C6L Sincerely, Signature: Client’s name / title : Wes Yan / PM Contact information / address : Room 201, Building A, No.1 Qianwan Road, Qianhai Shenzhen- Hong Kong Cooperation Zone, Shenzhen, Guangdong, China Tel: 13434704210 E-Mail: [email protected]

Shenzhen Zhiling Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022-10-26 Subject; Request for Confidentiality FCC ID: 2A2VW-C6L To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Wes Yan Title: PM

Page 1 of 4 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Fig. 1 Fig. 2 Page 2 of 4 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 4 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 4 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8

Page 1 of 1 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L4.0cm x 2.5cm) Label Location WirelessCam Lite Model: C6L FCC ID: 2A2VW-C6L IC: 28138-C6L

Page 1 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Page 2 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 BT/WIFI ANT Page 4 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 Fig. 12 Page 7 of 7 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 13

Page 1 of 4 FCC ID: 2A2VW-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information FCC ID 2A2VW-C6L Product name WirelessCam Lite Model number C6L Additional Model No. .......................................................................................................................... C6E,C6P,C6S,DC6L,DC6E,DC6P,DC6S Model Declaration PCB board, structure and internal of these model(s) are the same, So no additional models were tested Power supply Input: DC 5V, 1A Max DC 3.7V by Rechargeable Li-ion Battery, 5Ah Modulation Type GFSK for Bluetooth V5.0(DTS) IEEE 802.11b: DSSS (CCK, DQPSK, DBPSK) IEEE 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11n: OFDM (64QAM, 16QAM, QPSK, BPSK) Antenna Type PIFA Antenna Antenna Gain 2.58dBi(Max.) Hardware version V2 Software version 0.0.14 FCC Operation frequency 2402MHz-2480MHz 2412MHz-2462MHz Exposure category General population/uncontrolled environment EUT Type Production Unit Device Type Mobile Devices 2. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. Page 2 of 4 FCC ID: 2A2VW-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 3. Limit 3. 1 Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices 3. 2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 4. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. Antenna Information PIFA Antenna can only use antennas certificated as follows provided by manufacturer; Internal Identification Antenna type and antenna number Operate frequency band Maximum antenna gain Note Antenna PIFA Antenna 2400MHz-2500MHz 2.58dBi BT/WIFI Antenna Page 3 of 4 FCC ID: 2A2VW-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 6. Conducted Power < BT LE Max Conducted Power > Mode Channel Frequency(MHz) Max Conducted Power (dBm) GFSK 0 2402 0.11 19 2440 -0.01 39 2480 0.34 <2.4GWLAN Max Conducted Power > Mode Channel Frequency(MHz) Max Conducted Power (dBm) IEEE 802.11b 1 2412 15.01 6 2437 14.05 11 2462 13.91 IEEE 802.11g 1 2412 13.88 6 2437 13.40 11 2462 13.20 IEEE 802.11n HT20 1 2412 13.87 6 2437 13.58 11 2462 13.14 7. Manufacturing Tolerance <BT LE> GFSK (Peak) Channel Channel 0 Channel 19 Channel 39 Target (dBm) 0 0 0 Tolerance ±(dB) 1.0 1.0 1.0 <2.4G WIFI> 11B (Peak) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 15.0 14.0 13.0 Tolerance ±(dB…

Text truncated - open the document above for the full version.

SPECIFICATION ShenZhenTianDaCommunicationCo,LTD C6LAntenna ProductSpecification CustomerXunMeiZhiLianFrequencyband 2400-2500MHz ProjectnameC6L EditionA ItemnumberZL-C6-L0-WI-A Colour Originalcolor RFdesign Wangxinchuang Structuraldesign Hesenlin Date 2022.10.22 Customerconfirmation： Whethertheassemblymeetsyourrequirements ：□ OK □ NG ShenZhenTianDaCommunicationCO.,LTD. ShenZhenTianDaCommunicationCO.,LTD. 5EBuildingL,NO26Alley2BaicaiSciencePark, LiuxianRoad,71District,BaoanDistrict,Shenzhen TEL:0755-22194566 FAX:0755-22194566 5EBuildingL,NO26Alley2BaicaiSciencePark, LiuxianRoad,71District,BaoanDistrict,Shenzhen TEL:0755-22194566 FAX:0755-22194566 ConfidentialInformation Page 2 Catalog 一、WIFIantenna...................................................................................................................3 1、Specifications..................................................................................................................3 1.1、Electricalspecifications...............................................................................................3 1.1.1、Electricalperformanceindex....................................................................................3 1.1.2、Matchingcircuitdiagram..........................................................................................3 1.2、Testing..........................................................................................................................4 1.2.1、Passivetestdata........................................................................................................4 1.2.1.1、Standingwavepatternofantenna........................................................................4 1.2.1.2、Antennagainefficiency.........................................................................................4 1.2.1.3、Antennapattern......................................................................................................5 1.2.2、Activetestdata.........................................................................................................6 二、Structuralspecifications................................................................................................6 2.1、Antennacomposition...................................................................................................6 2.2、Drawings.....................................................................................................................7 2.3、Dimensionalmeasurement...........................................................................................7 三、Conclusion........................................................................................................................7 四、Packaging..........................................................................................................................7 ConfidentialInformation Page 3 一、WIFIAntenna 1、Specifications Thespecificationmainlyprovidestheteststatusofelectricalandstructural performanceparametersofWIFIantennainC6Lcamerasproject。Thepicturebelow showstheWIFIantennadesignedbyTianda. 1.1、Electricalspecifications 1.1.1、Electricalperformanceindex Theoperatingfrequencybandoftheantenna2400MHz—2500MHz，Thefollowing istheelectricalperformanceindexoftheantennadesignedandproducedbyTianda. WIFI 频段频率（MHz） VSWR 2.4G2400~2500 ≤2.0 1.1.2 、 Matchingcircuitdiagram ThematchingcircuitoftheWIFIantennais2.7nHinductorinseries(atE4). ConfidentialInformation Page 4 1.2、Testing 1.2.1、Passivetest 1.2.1.1、VSWR 1.2.1.2、AntennaGainandEfficiency ConfidentialInformation Page 5 1.2.1.3、Antennapattern ConfidentialInformation Page 6 1.2.2、Activetest Aboveisthewholemachine'sactivetestdata. 二、Structuralspecifications 2.1、Antennacomposition TheWIFIantennaismainlymadeofcopperware. ConfidentialInformation Page 7 2.2、Drawings 2.3、Dimensionalmeasurement 数量 重点尺寸 1234 18.35±1.00 19.2818.8619.3119.20 13.40±0.15 13.4113.4213.4013.39 2.10±0.15 2.102.112.092.23 三、Conclusion Thisantennaisdesignedontheprototypeprovidedbythecustomeratpresent.The electricalparametersandthestructuresizehavereachedthetechnicalrequirements, pleaseconfirm! 四、Packaging Packinplasticboxes.

Page 1 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Appendix A RF Test Data for BLE (Conducted Measurement) Product Name: WirelessCam Lite Test Model: C6L Environmental Conditions Temperature: 23.5 C Relative Humidity: 52.2% ATM Pressure: 100.0 kPa Test Engineer: Taylor Hu Supervised by: Li Huan Page 2 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.1 DTS Bandwidth Test Result TestMode Antenna Channel DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant 2402 0.708 2401.636 2402.344 0.5 PASS 2440 0.712 2439.632 2440.344 0.5 PASS 2480 0.712 2479.632 2480.344 0.5 PASS Page 3 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs BLE_Ant_2402 BLE_Ant_2440 BLE_Ant_2480 Page 4 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 5 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.2 Occupied Channel Bandwidth Test Result TestMode Antenna Channel OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant 2402 1.0606 2401.4767 2402.5373 --- PASS 2440 1.0578 2439.4731 2440.5309 --- PASS 2480 1.0571 2479.4724 2480.5295 --- PASS Page 6 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs BLE_Ant_2402 BLE_Ant_2440 BLE_Ant_2480 Page 7 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 8 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.3 Maximum conducted output power Test Result TestMode Antenna Channel Result[dBm] Limit[dBm] Verdict BLE Ant 2402 0.11 ≤30 PASS 2440 -0.01 ≤30 PASS 2480 0.34 ≤30 PASS Page 9 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs BLE_Ant_2402 BLE_Ant_2440 BLE_Ant_2480 Page 10 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 11 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.4 Maximum power spectral density Test Result TestMode Antenna Channel Result[dBm/3kHz] Limit[dBm/3kHz] Verdict BLE Ant 2402 -15.01 ≤8.00 PASS 2440 -15.12 ≤8.00 PASS 2480 -14.79 ≤8.00 PASS Page 12 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs BLE_Ant_2402 BLE_Ant_2440 BLE_Ant_2480 Page 13 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Page 14 of 27 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity A.5 Band edge measurements …

Text truncated - open the document above for the full version.

Page 1 of 53 FCC ID: 2A2VW-C6L IC: 28138-C6L Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial …

Text truncated - open the document above for the full version.