2A2WS-K3PROBiometric Safe

Jiangxi Fingerchip Intelligent Technology Co.,Ltd No.133 Yishang Avenue, Economic Development Zone, Yichun City, Jiangxi Province, China https://www.pineworld.net [email protected]. K3 Pro Biometric Safe User Manual Please read this instruction carefully before using the product. Jiangxi Fingerchip Intelligent Technology Co.,Ltd. reserves the final right to interpret this manual. PINEWORLD V1.1 1.Notice Thanks for using PINEWORLD K3 Pro Smart Gun Safe.To bring you a better experience, please read the User Manual first. -1--2- Notice---------------------------------2 ----------------------------3Introduction User Guide-----------------------------4 Fixation Instructions----------------------8 FAQ----------------------------------9 Contents Initial Password: 123456 Add Administrator/User: Long Press 6 Mute Mode: Long Press 2 Fast Pairing: Long Press 3 Remotely Unlock: Long Press 4 Quick Start Guide A. If it is the first time unpack the box, please use the backup key to unlock it. B. Please change the original passcode as soon as possible and do not disclose the passcode. C. About emergency charging: ①The power supply port only supports emergency power supply and does not support long-term power supply. ② IfThe product is not equipped with charging cable. necessary, please prepare a charging cable (5V-2A Max) at home to unlock it in an emergency. ③In order not to affect your further use, please replace the battery timely after emergency unlocking, D. Keep your fingers clean when using the fingerprint to unlock. E. The acceptable operating temperature for the product ranges from -25°C to 55°C. F. Do not use corrosive materials to clean the device. Otherwise, the protective coat of the device may be damaged. G. Neither keep the battery near the fire source nor use metal objects to connect the two poles of the battery, which will incur short-circuit of the battery and even explosion. What’s In The Box K3 Smart Safety Box User Manual Please read this instruction carefully before using the product. Shenzhen Zhixin IoT Technology Co., Ltd. reserves the final right to interpret this manual. PINEWORLD User Manual Backup Keys K3 Biometric Smart Safe Security Steeel Cable A. Install the battery ① Please use the backup key to unlock and open the battery compartment cover; ② Gently unplug the battery compartment and put in four new AA batteries of the same brand (Note: do not pull the battery compartment vigorously.) ③ Put the battery compartment and connecting wire into the trough. B. Add the administrator Press and hold the key No. 6 and add administrators according to the voice prompt. (The first two are for administrators, and the first one must be in the form of passcode, and the second one can be fingerprint or passcode. 3.User Guide Key Hole Note: ① Passcodes setting: a 6-digit passcode must be set. The passcode entered should not be too simple. (e.g. 123456) ② Fingerprints setting: you are required to press the same finger 6 times. To improve the fingerprint recognition rate, it is recommended to press the same finger at different angles and locations. Do not change your fingers during the fingerprint recording. The product is a smart safety box that supports multiple unlocking ways, including fingerprint, passcode, remote unlocking and backup key unlocking. With the unlocking speed of 0.5s, it helps you quickly take out your items; multiple intelligent alarms such as trial-and-error alarm, tamper alarm, coercive alarm, and low power alarm bring you more smart experience; multiple anti-theft designs including steel cable, fixed hole, C-level key cylinder and alarm can effectively prevent thieves from destroying the equipment and safeguard the product. Furthermore, the device has been connected to the FC Smarthome APP, which enable you to experience the scientific and technological charm of intelligent management and control. Introduction to keys a. passcode keyboard b. fingerprint identification scanner c. keyhole d. tamper key e. setting key f. loudspeaker port g. emergency charging port h. steel cable entrance Disassembly and installation of battery compartment - step demonstration (When replacing the battery, do not pull the battery compartment vigorously.) 2.Introduction Specification Color Size Weight Unlocking ways Fingerprint resolution Capacity Type-C Input Power Black 285mm*225mm*65mm 7.7lbs Fingerprint, Passcode, APP unlocking, Backup key 500DPI Fingerprint: 50, Passcode: 50 5V-2A(Max) a b c d e f g -3--4- h D. Other operations Local shortcut keys: ① Coercive alarm: when the passcode or fingerprint dedicated to the coercive alarm is used to unlock the device, the message receiver will be informed of the danger encountered by the user, and the information will be reported in the APP. (Setting path: APP setting - coercive setting - coercive object and acceptor setting - successful saving) ②Prying-resistant alarm: When the device is damaged and the anti- disassembly key is loose, the alarm will be triggered to sound as long as 180s and the information will be reported in the APP. ③ Low voltage warning: when the power is low, the warning message will be broadcast. Please replace the battery in time. ④ Alarm clearing method: verify the registered passcode or fingerprint to clear alarms. ①Check the version: hold down key No.1 ②Mute mode: hold down Key No. 2 to support mute/unmute adjustment. ③Fast pairing: hold down Key No. 3 to bind in the smart APP (FC Smarthome). ④Remotely unlock: hold down Key No. 4 (used only when paired). ⑤Change the passcode: hold down Key No.5 (Only support the passcode change.). ⑥Add users: hold down Key No. 6. ⑦Delete users: hold down Key No. 6, and after verifying the administrator hold down 6 again. ⑧Factory Reset: long-press setting button for 3 seconds (need to verify administrator) Local alarm and others: C. Bind mobile phones to the device ·Scan the QR code to download the Smart APP (FC Smarthome); ·Open the APP and select manually add -smart safety …

Text truncated - open the document above for the full version.

Jiangxi Fingerprint Intelligent Technology Co., Ltd. No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-4-8 To whom it may concern: We, Jiangxi Fingerprint Intelligent Technology Co., Ltd., hereby certify that the equipment for which authorization is sought (FCC ID: 2A2WS-K3PRO) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Peng Wu Manager Jiangxi Fingerprint Intelligent Technology Co., Ltd. 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Jiangxi Fingerprint Intelligent Technology Co., Ltd. No.133 Yishang Avenue, Economic Development Zone, Yichun City, Jiangxi Province, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 3/25/2024 U.S. Agent Designation Jiangxi Fingerprint Intelligent Technology Co., Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A2WS-K3PRO): Name and company of U.S. agent: Formates LLC Physical U.S. address of agent: 1400 Hudson St, Hoboken, New Jersey, 07030, USA FRN of U.S. agent: 0033456468 Email address of U.S. agent: [email protected] Formates LLC acknowledges their obligation to accept service of process on behalf of Jiangxi Fingerprint Intelligent Technology Co., Ltd.. Jiangxi Fingerprint Intelligent Technology Co., Ltd. with the FRN 0031269574 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Peng Wu Manager Jiangxi Fingerprint Intelligent Technology Co., Ltd. Signature Abi Aribisala Project Manager Formates LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-4-8> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2A2WS-K3PRO K3 Pro For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Peng Wu/Manager Company: Jiangxi Fingerprint Intelligent Technology Co., Ltd. Address: No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Phone: 86-795-3668288 Fax: 86-795-3668288 E-Mail: [email protected]

Jiangxi Fingerprint Intelligent Technology Co., Ltd. No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Date: 2024-4-8 FCC ID: 2A2WS-K3PRO Model Number: K3 Pro To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Jiangxi Fingerprint Intelligent Technology Co., Ltd., declare that this EUT (FCC ID: 2A2WS-K3PRO) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title： Peng Wu/Manager Company: Jiangxi Fingerprint Intelligent Technology Co., Ltd. Address: No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Phone: 86-795-3668288 Fax: 86-795-3668288 E-Mail: [email protected]

Jiangxi Fingerprint Intelligent Technology Co., Ltd. No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-4-8 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2A2WS-K3PRO including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Peng Wu/Manager Company: Jiangxi Fingerprint Intelligent Technology Co., Ltd. Address: No.133,Yishang Avenue, Economic development Zone, Yichun, Jiangxi, China Phone: 86-795-3668288 Fax: 86-795-3668288 E-Mail: [email protected]

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 1 of 4 EXTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 2 of 4 Fig.3 Fig.4 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 3 of 4 Fig.5 Fig.6 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 4 of 4 Fig.7

Label Location: FCC ID: 2A2WS-K3PRO This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 1 of 5 INTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 2 of 5 Fig.3 Fig.4 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 3 of 5 Fig.5 Fig.6 WiFi antenna Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 4 of 5 Fig.7 Fig.8 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Page 5 of 5 Fig.9 Fig.10

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shzhen Tongzhou Testing Co.,Ltd Page 1 of 6 Maximum Permissible Exposure Report 1. Product Information EUT : Biometric Safe Model Number : K3 Pro Model Declaration : N/A Test Model : K3 Pro Power Supply : Input: USB 5V, 2A Hardware version : K3B KEY 0V2 2404 Software version : V1.0 2. Evaluation Method Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. In accordance with KDB447498D01 for Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modelled or measured field strengths or power density, is ≤ 1.0. The MPE ratio of each antenna is determined at the minimum test separation distance required by the operating configurations and exposure conditions of the host device, according to the ratio of field strengths or power density to MPE limit, at the test frequency. Either the maximum peak or spatially averaged results from measurements or numerical simulations may be used to determine the MPE ratios. Spatial averaging does not apply when MPE is estimated using simple calculations based on far-field plane-wave equivalent conditions. The antenna installation and operating requirements for the host device must meet the minimum test separation distances required by all antennas, in both standalone and simultaneous transmission operations, to satisfy compliance. Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shzhen Tongzhou Testing Co.,Ltd Page 2 of 6 3. Limit 3.1 Refer evaluation method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General 1 RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices 3. 2 Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 1842/f 61.4 / / 1.63 4.89/f 0.163 / / (100) * (900/f 2 )* 1.0 f/300 5 6 6 6 6 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 3.0 – 30 30 – 300 300 – 1500 1500 – 100,000 614 824/f 27.5 / / 1.63 2.19/f 0.073 / / (100) * (180/f 2 )* 0.2 f/1500 1.0 30 30 30 30 30 F=frequency in MHz *=Plane-wave equivalent power density 4. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 5. Antenna Information Antenna Gain and type refer to Antenna specification Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shzhen Tongzhou Testing Co.,Ltd Page 3 of 6 6. Conducted Power 2.4G Band: WiFi 2.4GHz Band Test Mode Antenna Frequency[M Hz] Result [dBm] 11B Ant1 2412 17.22 11B Ant1 2437 15.81 11B Ant1 2462 16.47 11G Ant1 2412 17.07 11G Ant1 2437 16.68 11G Ant1 2462 16.78 11N20SISO Ant1 2412 16.56 11N20SISO Ant1 2437 16.27 11N20SISO Ant1 2462 16.09 11N40SISO Ant1 2422 17.19 11N40SISO Ant1 2437 16.80 11N40SISO Ant1 2452 16.33 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shzhen Tongzhou Testing Co.,Ltd Page 4 of 6 7. Manufacturing Tolerance WiFi 2.4GHz Band – Antenna 1 IEEE 802.11b(Average) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 16.5 15.5 16.0 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11g (Average) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 16.5 16.0 16.5 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11n HT20 (Average) Channel Channel 1 Channel 6 Channel 11 Target (dBm) 16.0 16.0 15.5 Tolerance ±(dB) 1.0 1.0 1.0 IEEE 802.11n HT40 (Average) Channel Channel 3 Channel 6 Channel 9 Target (dBm) 16.5 16.5 16.0 Tolerance ±(dB) 1.0 1.0 1.0 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO This report shall not be reproduced except in full, without the written approval of Shzhen Tongzhou Testing Co.,Ltd Page 5 of 6 8. Measurement Results 8.1 Standalone MPE As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used antenna refer to antenna information, the RF power density can be obtained. WiFi 2.4GHz Band – Ant 1 Modulation Type Output power Antenna Gain Antenna Gain MPE MPE (dBi) (linear) (mW/cm 2 ) Limits dBm mW (mW/cm 2 ) IEEE 802.11b 17.5 56.2341 -1.0 0.7943 0.0112 1.0000 IEEE 802.11g 17.5 56.2341 -1.0 0.7943 0.0112 1.0000 IEEE 802.11n HT20 17.0 50.1187 -1.0 0.7943 0.0…

Text truncated - open the document above for the full version.

Antenna FCM100D Datasheet Antenna Services Version: 1.0 Date: 2022-11-09 Status: Preliminary Antenna Services XXXXXXXX Datasheet Antenna_Datasheet 1 / 14 At Quectel, our aim is to provide timely and comprehensive services to our customers. If you require any assistance, please contact our headquarters: Quectel Wireless Solutions Co., Ltd. Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai 200233, China Tel: +86 21 5108 6236 Email: [email protected] Or our local offices. For more information, please visit: http://www.quectel.com/support/sales.htm. For technical support, or to report documentation errors, please visit: http://www.quectel.com/support/technical.htm. Or email us at: [email protected]. Legal Notices We offer information as a service to you. The provided information is based on your requirements and we make every effort to ensure its quality. You agree that you are responsible for using independent analysis and evaluation in designing intended products, and we provide reference designs for illustrative purposes only. Before using any hardware, software or service guided by this document, please read this notice carefully. Even though we employ commercially reasonable efforts to provide the best possible experience, you hereby acknowledge and agree that this document and related services hereunder are provided to you on an “as available” basis. We may revise or restate this document from time to time at our sole discretion without any prior notice to you. Use and Disclosure Restrictions License Agreements Documents and information provided by us shall be kept confidential, unless specific permission is granted. They shall not be accessed or used for any purpose except as expressly provided herein. Copyright Our and third-party products hereunder may contain copyrighted material. Such copyrighted material shall not be copied, reproduced, distributed, merged, published, translated, or modified without prior written consent. We and the third party have exclusive rights over copyrighted material. No license shall be granted or conveyed under any patents, copyrights, trademarks, or service mark rights. To avoid ambiguities, purchasing in any form cannot be deemed as granting a license other than the normal non-exclusive, royalty-free license to use the material. We reserve the right to take legal action for noncompliance with abovementioned requirements, unauthorized use, or other illegal or malicious use of the material. Antenna Services XXXXXXXX Datasheet Antenna_Datasheet 2 / 14 Trademarks Except as otherwise set forth herein, nothing in this document shall be construed as conferring any rights to use any trademark, trade name or name, abbreviation, or counterfeit product thereof owned by Quectel or any third party in advertising, publicity, or other aspects. Third-Party Rights This document may refer to hardware, software and/or documentation owned by one or more third parties (“third-party materials”). Use of such third-party materials shall be governed by all restrictions and obligations applicable thereto. We make no warranty or representation, either express or implied, regarding the third-party materials, including but not limited to any implied or statutory, warranties of merchantability or fitness for a particular purpose, quiet enjoyment, system integration, information accuracy, and non-infringement of any third-party intellectual property rights with regard to the licensed technology or use thereof. Nothing herein constitutes a representation or warranty by us to either develop, enhance, modify, distribute, market, sell, offer for sale, or otherwise maintain production of any our products or any other hardware, software, device, tool, information, or product. We moreover disclaim any and all warranties arising from the course of dealing or usage of trade. Privacy Policy To implement module functionality, certain device data are uploaded to Quectel’s or third-party’s servers, including carriers, chipset suppliers or customer-designated servers. Quectel, strictly abiding by the relevant laws and regulations, shall retain, use, disclose or otherwise process relevant data for the purpose of performing the service only or as permitted by applicable laws. Before data interaction with third parties, please be informed of their privacy and data security policy. Disclaimer a) We acknowledge no liability for any injury or damage arising from the reliance upon the information. b) We shall bear no liability resulting from any inaccuracies or omissions, or from the use of the information contained herein. c) While we have made every effort to ensure that the functions and features under development are free from errors, it is possible that they could contain errors, inaccuracies, and omissions. Unless otherwise provided by valid agreement, we make no warranties of any kind, either implied or express, and exclude all liability for any loss or damage suffered in connection with the use of features and functions under development, to the maximum extent permitted by law, regardless of whether such loss or damage may have been foreseeable. d) We are not responsible for the accessibility, safety, accuracy, availability, legality, or completeness of information, advertising, commercial offers, products, services, and materials on third-party websites and third-party resources. Copyright © Quectel Wireless Solutions Co., Ltd. 2022. All rights reserved. Antenna Services XXXXXXXX Datasheet Antenna_Datasheet 3 / 14 About the Document Revision History Version Date Author Note - 2022-11-09 Boris.Wang Creation of the document 1.0 2022-11-09 Boris.Wang First official release Antenna Services XXXXXXXX Datasheet Antenna_Datasheet 4 / 14 Contents About the Document ................................................................................................................................... 3 Contents ..........................................…

Text truncated - open the document above for the full version.

Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 1 of 39 Appendix Test Data for WLAN(2.4G) (Conducted Measurement) Product Name: Biometric Safe Trade Mark: PINEWORLD Test Model: K3 Pro FCC ID: 2A2WS-K3PRO Environmental Conditions Temperature: 23.8°C Relative Humidity: 58% ATM Pressure: 100.0 kPa Test Engineer: Anna Hu Supervised by: Hugo Chen NOTE N/A Appendix A: DTS Bandwidth Test Result TestMode Antenna Frequency[MHz] DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 10.040 2406.960 2417.000 0.5 PASS 11B Ant1 2437 10.080 2431.960 2442.040 0.5 PASS 11B Ant1 2462 10.000 2456.960 2466.960 0.5 PASS 11G Ant1 2412 15.560 2404.320 2419.880 0.5 PASS 11G Ant1 2437 16.280 2428.840 2445.120 0.5 PASS 11G Ant1 2462 15.760 2454.120 2469.880 0.5 PASS 11N20SISO Ant1 2412 13.880 2405.680 2419.560 0.5 PASS 11N20SISO Ant1 2437 15.600 2429.200 2444.800 0.5 PASS 11N20SISO Ant1 2462 15.760 2454.080 2469.840 0.5 PASS 11N40SISO Ant1 2422 35.040 2404.480 2439.520 0.5 PASS 11N40SISO Ant1 2437 35.520 2419.080 2454.600 0.5 PASS 11N40SISO Ant1 2452 35.120 2434.480 2469.600 0.5 PASS Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 2 of 39 Test Graphs 11B-Ant1-2412-PASS 11B-Ant1-2437-PASS 11B-Ant1-2462-PASS Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 3 of 39 11G-Ant1-2412-PASS 11G-Ant1-2437-PASS 11G-Ant1-2462-PASS Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 4 of 39 11N20SISO-Ant1-2412-PASS 11N20SISO-Ant1-2437-PASS 11N20SISO-Ant1-2462-PASS Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 5 of 39 11N40SISO-Ant1-2422-PASS 11N40SISO-Ant1-2437-PASS 11N40SISO-Ant1-2452-PASS Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 6 of 39 Appendix B: Occupied Channel Bandwidth Test Result TestMode Antenna Channel Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 14.785 2404.6471 2419.4321 --- --- 11B Ant1 2437 14.812 2429.5933 2444.4053 --- --- 11B Ant1 2462 14.747 2454.6266 2469.3736 --- --- 11G Ant1 2412 16.752 2403.6533 2420.4053 --- --- 11G Ant1 2437 16.794 2428.6384 2445.4324 --- --- 11G Ant1 2462 16.748 2453.6426 2470.3906 --- --- 11N20SISO Ant1 2412 17.821 2403.1176 2420.9386 --- --- 11N20SISO Ant1 2437 17.821 2428.1286 2445.9496 --- --- 11N20SISO Ant1 2462 17.853 2453.0753 2470.9283 --- --- 11N40SISO Ant1 2422 36.184 2403.9267 2440.1107 --- --- 11N40SISO Ant1 2437 36.230 2418.9471 2455.1771 --- --- 11N40SISO Ant1 2452 36.227 2433.9728 2470.1998 --- --- Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 Page 7 of 39 Test Graphs 11B-Ant1-2412 11B-Ant1-2437 11B-Ant1-2462 Shenzhen Tongzhou Testing Co.,Ltd FCC ID: 2A2WS-K3PRO Report No.: TZ240305444-WiFi2G4 …

Text truncated - open the document above for the full version.