2A3J6-MJ6508REMOTEBicycle Light Remote Control

BICYCLE LIGHT HOW TO INSTALL USER MANUAL Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference! RN 2000 WARNING • DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes. • DO NOT cover the light head when the bicycle light is on, or place the bicycle light head on the ground. The radiation energy of the bicycle light may cause damage to the bicycle light itself, or even result in burning to flammable objects. DANGER NOTICE • Store the light at room temperature in a dry place. Avoid moisture, or extreme hot or cold. • Store the light in the charged condition. Avoid “deep discharge". Battery life will decrease if the light is stored in a fully discharged condition. • Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time. • When the run time is unsatisfactory, please recycle. DO NOT open the case of the light or incinerate. 3mm Hex Type-C USB Cable Aero Bar Compatible Strap Handlebar MountRN 2000 GoPro Mount EXCLUSION CLAUSE Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode. 操作说明 遥控器配对操作： *使用遥控器前，请先取下电池绝缘垫片并重新装入 电池。 打开车灯，长按遥控器两个按键约10秒进入配对模 式，此时遥控器两个按键指示灯将以蓝灯交替闪烁。 将遥控器紧靠车灯进行自动配对，配对成功后遥控器 和车灯蓝色指示灯分别亮2秒熄灭。 遥控器按键操作： 开机/关机：长按任意键1秒 亮度切换：单击“○”键 模式切换：双击“○”键 闪烁切换：双击“□”键 一键极亮：单击“□”键进入一键极亮，按任意键退 出。 *车灯关机48小时后不操作，遥控器将进入休眠状态， 需单击车灯按键将其激活或长按车灯按键开机，遥控器 才可正常使用。 ( CN ) 简体中文 OPEN HERE HOW TO RECHARGE ChargingFully Charged FLASH RED Green Standard Charging Time: Approx.3.5hrs (5V 2A) When the device is power-on, the indicator on the power button will indicate the battery level. When the device is power-off, short press the power button to activate the indicator light (light will shut down automatically after 2 seconds). BATTERY INDICATOR RED 20%-11% FLASH RED 10%-1% GREEN 100%-21% Note: Charging cables need to be purchased separately. PHONE CHARGING INSTRUCTION (5V 3A) OPERATING INSTRUCTIONS REMOTE CONTROL PAIRING: *Before using the remote control, please remove the insulating spacer and reinstall the battery. Turn on the light, press and hold the "○""□" buttons on the remote for about 10 seconds until the indicator alternately flashes blue to enter pairing mode. Then, close the remote to the light until the indicators on the remote and light unit are constantly blue for 2 seconds, confirming a successful pairing. REMOTE CONTROL OPERATION: ON/OFF: Press and hold the "○"/"□" button for 1 second ADJUST BRIGHTNESS: Click the "○" button CHANGE MODE: Double click the "○" button FLASH MODE: Double click the "□" button FULL OUTPUT MODE (2000LM): Click the "□" button to go into full output mode and click the "○"/"□" button to return to the previous mode. *The remote control will enter sleep mode if the light is turned off for 48 hours without any operation. Click the light's button to activate it or long-press the light's button to turn it on, and the remote control can work normally. HEADLIGHT BUTTON INSTRUCTIONS: ON/OFF: Press and hold the button to turn the light on/off. The default output is the last mode when turned off. ADJUST BRIGHTNESS: Click the "︵" button to increase the brightness, and click the "︶" button to decrease the brightness. CHANGE MODE: Double click the button to change between floodlight mode and hybrid mode. ( EN ) English 01 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. 02 车灯按键操作： 开机/关机：长按开关1秒 调节亮度：单击“︵”键调高亮度，单击“︶”键调 低亮度 模式切换：双击开关循环切换近光模式及远近光模式 锁键：关机状态下，长按开关3秒进入锁定状态（按 键锁定后，除解锁操作，其他操作均不能开启车灯， 只有红色指示灯快闪提示） 解锁：锁键状态下，长按开关3秒解锁车灯 智能模式：车灯出厂默认关闭智能模式，双击并长按 3秒可开启或关闭智能模式。在智能模式下，车灯静 置2分钟将自动熄灭，任何震动都会自动亮起。若30 分钟内未感知到震动，车灯将自动进入关机状态； 白天时，车灯自动降低亮度至近光最低档，当进入隧 道或感知环境变暗时，车灯自动恢复开机时的档位亮 度。 KÄYTTÖ OHJEET PARILIITOS KAUKOSÄÄTIMESTÄ: *Irrota eristävä välikappale ja asenna paristo takaisin paikalleen ennen kaukosäätimen käyttöä. Kytke valo päälle, paina ja pidä painettuna kaukosäätimen "○""□"-painikkeita noin 10 sekunnin ajan, kunnes merkkivalo vilkkuu vuorotellen sinisenä siirtyäksesi pariliitostilaan. Aseta sitten kaukosäädin lähelle ajovaloa, kunnes kaukosäätimen ja valo…

Text truncated - open the document above for the full version.

DongguanOlightE-CommerceTechnologyCo.,Ltd TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB986446D01. FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 7/19/23 Towhomitmayconcern: We,[DongguanOlightE-CommerceTechnologyCo.,Ltd],herebycertifythattheequipmentfor whichauthorizationissought(FCCID:[2A3J6-MJ6508REMOTE])isnot“covered”equipment prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903oftheFCCrules. Wealsocertifythat,asofthedateofthefilingoftheapplication,wearenotidentifiedontheCovered List(https://www.fcc.gov/supplychain/coveredlist)asanentityproducing“covered”equipment. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirements listedunder§2.911(b)and(d)(5)and(6). Sincerely, Signature [AthenaHuang] [Manager] [DongguanOlightE-CommerceTechnologyCo.,Ltd

ProjectNo.:18220WC301326Page1of3 Code:AB-RF-05-b AppendixII--ExternalPhotograph ProjectNo.:18220WC301326Page2of3 Code:AB-RF-05-b ProjectNo.:18220WC301326Page3of3 Code:AB-RF-05-b

LabelLocationOnEUT Theproductistoosmalltoplacecompletelabelinformation,sothelabelisplacedintheuser manual. Label

ProjectNo.:18220WC301326Page1of3 Code:AB-RF-05-b AppendixIII--InternalPhotograph ProjectNo.:18220WC301326Page2of3 Code:AB-RF-05-b ANT ProjectNo.:18220WC301326Page3of3 Code:AB-RF-05-b

RFEXPOSUREEVALUATION FCCID:2A3J6-MJ6508REMOTE AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeused toevaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF) Radiationasspecifiedin§1.1307(b): RoutineSARevaluationreferstothatspecificallyrequiredby§2.1093,using measurementsorcomputersimulation.WhenroutineSARevaluationisnot required,portabletransmitterswithoutputpowergreaterthantheapplicable lowthresholdrequireSARevaluationtoqualifyforTCBapproval. Channel (MHz) Maximum output power (dBm) Tuneup tolerance (dBm) MaxTuneUp Power(dBm) Distance (mm) Calculation results Limit Operating Mode 24020.950.95 ±1 1.95050.4863 BLE_1M 24400.470.47±11.47050.4383 24800.270.27±11.27050.4223 24020.960.96 ±1 1.96050.4873 BLE_2M 24400.430.43±11.43050.4343 24800.270.27±11.27050.4223 Result:NoStandaloneSARtestisrequired.

Page1of33 AppendixTestData ReportNo.:18220WC30132601TestSampleNo.:1-2-2 StartTestDate:2023.06.29FinishTestDate:2023.06.30 TestEngineer:Auditor: Temperature:25.2 °C RelativeHumidity:50% Pressure:1012hPa AppendixA:DTSBandwidth TestResult TestModeAntennaFrequency[MHz] DTSBW [MHz] FL[MHz]FH[MHz]Limit[MHz]Verdict BLE_1MAnt1 24020.7162401.6562402.3720.5PASS 24400.7082439.6762440.3840.5PASS 24800.7562479.6442480.4000.5PASS BLE_2MAnt1 24021.1202401.4642402.5840.5PASS 24401.1162439.4602440.5760.5PASS 24801.1242479.4522480.5760.5PASS Page2of33 TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page3of33 BLE_2M_Ant1_2402 BLE_2M_Ant1_2440 Page4of33 BLE_2M_Ant1_2480 Page5of33 AppendixB:OccupiedChannelBandwidth TestResult TestModeAntennaFrequency[MHz] OCB[MHz] FL[MHz]FH[MHz] BLE_1MAnt1 24021.12442401.45072402.5751 24401.13672439.44332440.5800 24801.14652479.44402480.5905 BLE_2MAnt1 24022.07692400.99372403.0706 24402.06982438.99642441.0662 24802.07592478.99192481.0678 Page6of33 TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page7of33 BLE_2M_Ant1_2402 BLE_2M_Ant1_2440 Page8of33 BLE_2M_Ant1_2480 Page9of33 AppendixC:Maximumconductedoutputpower TestResultPeak TestModeAntennaFrequency[MHz] ConductedPeak Power[dBm] Conducted Limit[dBm] Verdict BLE_1MAnt1 24020.95≤30PASS 24400.47≤30PASS 24800.27≤30PASS BLE_2MAnt1 24020.96≤30PASS 24400.43≤30PASS 24800.27≤30PASS Page10of33 TestGraphsPeak BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page11of33 BLE_2M_Ant1_2402 BLE_2M_Ant1_2440 Page12of33 BLE_2M_Ant1_2480 Page13of33 AppendixD:Maximumpowerspectraldensity TestResult TestModeAntennaFrequency[MHz]Result[dBm/3kHz]Limit[dBm/3kHz]Verdict BLE_1MAnt1 2402-15.63≤8.00PASS 2440-16.43≤8.00PASS 2480-16.95≤8.00PASS BLE_2MAnt1 2402-18.33≤8.00PASS 2440-18.71≤8.00PASS 2480-18.96≤8.00PASS Page14of33 TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page15of33 BLE_2M_Ant1_2402 BLE_2M_Ant1_2440 Page16of33 BLE_2M_Ant1_2480 Page17of33 AppendixE:Bandedgemeasurements TestResult TestMod e Antenn a ChNam e Frequency[MHz ] RefLevel[dBm ] Result[dBm ] Limit[dBm ] Verdic t BLE_1MAnt1 Low24020.13-34.98≤-19.88PASS High2480-0.54-45.21≤-20.54PASS BLE_2MAnt1 Low24020.20-34.78≤-19.8PASS High2480-0.69-45.93≤-20.69PASS Page18of33 TestGraphs BLE_1M_Ant1_Low_2402 BLE_1M_Ant1_High_2480 BLE_2M_Ant1_Low_2402 Page19of33 BLE_2M_Ant1_High_2480 Page20of33 AppendixF:ConductedSpuriousEmission TestResult TestMod e Antenn a Frequency[MHz ] FreqRange [MHz] RefLeve l [dBm] Result[dBm ] Limit[dBm ] Verdic t BLE_1MAnt1 2402 Reference0.000.00---PASS 30~10000.00-67.63≤-20PASS 1000~2650 0 0.00-37.87≤-20PASS 2440 Reference0.060.06---PASS 30~10000.06-68.61≤-19.94PASS 1000~2650 0 0.06-38.42≤-19.94PASS 2480 Reference-0.59-0.59---PASS 30~1000-0.59-68.71≤-20.59PASS 1000~2650 0 -0.59-39.19≤-20.59PASS BLE_2MAnt1 2402 Reference-2.17-2.17---PASS 30~1000-2.17-68.7≤-22.17PASS 1000~2650 0 -2.17-40.85≤-22.17PASS 2440 Reference-2.05-2.05---PASS 30~1000-2.05-67.47≤-22.05PASS 1000~2650 0 -2.05-38.42≤-22.05PASS 2480 Reference-2.21-2.21---PASS 30~1000-2.21-68.82≤-22.21PASS 1000~2650 0 -2.21-41.13≤-22.21PASS Page21of33 TestGraphs BLE_1M_Ant1_2402_0~Reference BLE_1M_Ant1_2402_30~1000 BLE_1M_Ant1_2402_1000~26500 Page22of33 BLE_1M_Ant1_2440_0~Reference BLE_1M_Ant1_2440_30~1000 Page23of33 BLE_1M_Ant1_2440_1000~26500 BLE_1M_Ant1_2480_0~Reference Page24of33 BLE_1M_Ant1_2480_30~1000 BLE_1M_Ant1_2480_1000~26500 Page25of33 BLE_2M_Ant1_2402_0~Reference BLE_2M_Ant1_2402_30~1000 Page26of33 BLE_2M_Ant1_2402_1000~26500 BLE_2M_Ant1_2440_0~Reference Page27of33 BLE_2M_Ant1_2440_30~1000 BLE_2M_Ant1_2440_1000~26500 Page28of33 BLE_2M_Ant1_2480_0~Reference BLE_2M_Ant1_2480_30~1000 Page29of33 BLE_2M_Ant1_2480_1000~26500 Page30of33 AppendixG:DutyCycle TestResult TestModeAntennaFrequency[MHz] ONTime [ms] Period [ms] DutyCycle [%] DutyCycle Factor[dB] BLE_1MAnt1 24020.400.6363.491.97 24400.400.6264.521.90 24800.400.6363.491.97 BLE_2MAnt1 24020.200.6232.264.91 24400.200.6331.754.98 24800.200.6232.264.91 Page31of33 TestGraphs BLE_1M_Ant1_2402 BLE_1M_Ant1_2440 BLE_1M_Ant1_2480 Page32of33 BLE_2M_Ant1_2402 BLE_2M_Ant1_2440 Page33of33 BLE_2M_Ant1_2480 ---End---

ReportNo.:18220WC30132601FCCID:2A3J6-MJ6508REMOTEPage1of28 Code:AB-RF-05-b FCCTestReport Applicant: DongguanOlightE-CommerceTechnology Co.,Ltd Address: 4thFloor,Building4,KeguIndustrialPark,No 6ZhongnanRoad,ChanganTown,Dongguan City,Guangdong,523000,China. ProductName:BicycleLightRemoteControl ReportDate:Jul.19,2023 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC30132601FCCID:2A3J6-MJ6508REMOTEPage2of28 Code:AB-RF-05-b Contents 1.GeneralInformation............................................................................................................................................6 1.1.ClientInformation....................................................................................................................................6 1.2.DescriptionofDevice(EUT)..................................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest................................................................................................7 1.4.DescriptionofTestConfiguration..........................................................................................................7 1.5.DescriptionOfTestSetup......................................................................................................................8 1.6.TestEquipmentList.................................................................................................................................9 1.7.MeasurementUncertainty....................................................................................................................10 1.8.DescriptionofTestFacility...................................................................................................................10 2.SummaryofTestResults................................................................................................................................11 3.ConductedEmissionTest................................................................................................................................12 3.1.TestStandardandLimit.......................................................................................................................12 3.2.TestSetup...............................................................................................................................................12 3.3.TestProcedure.......................................................................................................................................12 3.4.TestData.................................................................................................................................................12 4.RadiationSpuriousEmissionandBandEdge.............................................................................................13 4.1.TestStandardandLimit.......................................................................................................................13 4.2.TestSetup...............................................................................................................................................13 4.3.TestProcedure.......................................................................................................................................14 4.4.TestData.................................................................................................................................................15 5.MaximumPeakOutputPowerTest...............................................................................................................23 5.1.TestStandardandLimit.......................................................................................................................23 5.2.TestSetup...............................................................................................................................................23 5.3.TestProcedure.......................................................................................................................................23 5.4.TestData.................................................................................................................................................23 6.6DBOccupyBandwidthTest..........................................................................................................................24 6.1.TestStandardandLimit.......................................................................................................................24 6.2.TestSetup...............................................................................................................................................24 6.3.TestProcedure.......................................................................................................................................24 6.4.TestData.................................................................................................................................................24 7.PowerSpectralDensityTest...........................................................................................................................25 7.1.TestStandardandLimit.......................................................................................................................25 7.2.TestSetup...............................................................................................................................................25 7.3.TestProcedure.......................................................................................................................................25 7.4.TestData.................................................................................................................................................25 8.100kHzBandwidthofFrequencyBandEdgeRequirement......................................................................26 8.1.TestStandardandLimit....................................................................................................…

Text truncated - open the document above for the full version.

version01 DongguanOlightE-CommerceTechnologyCo.,Ltd DeclarationconcerningAntennaSpecification Itisherebydeclaredthattheproduct ModelNo.:MJ-6508 FCCID:2A3J6-MJ6508REMOTE fulfillstherequirementinFCCtestrelatingtotheantennatype. ThedevicespecifiedaboveconfirmstotheFCCrecommendationsfor internal antennatype(s) describedbelow: ModelNo.ofantenna:MJ6508 Typeofantenna:PCBantenna Gainoftheantenna:-1.07dBi Frequencyrange:2400-2500MHz Themountingoftheantennaisfixedtotheradiomoduleandnootherantennashouldbeused. Companyname:DongguanOlightE-CommerceTechnologyCo.,Ltd Address:4thFloor,Building4,KeguIndustrialPark,No6ZhongnanRoad,Changan Town,DongguanCity,Guangdong,523000,China City:Dongguan ZIP/Postalcode:/ Country:China Place:Date:7/19/2023 Signature:

深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 1 - 飞敏科技OTA 天线数据报告 1.Mockup model:MJ6508 日期：2022.7.16 1.1
Test the project： 2.Test Result 2.1 Test conditions Test Environment Conditions: Relative Humindity: 15....75％ Temperature: ＋10°C to ＋30°C Voltage of the EUT: N/A 天 线 无 源 数 据 VSWR/Smith Circle/Return Loss gain efficiency Directional diagram 深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 2 - 2.2 Test Results lists 2.2.1 SWR 深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 3 - 2.2.2 Smith Chart 2.2. 3 LOG MAG 深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 4 - 2.2. 4 Gain and Efficiency Frequency Gain(dBi) Efficiency 2400MHz -4.7610.25 2410MHz -4.0112.05 2420MHz -3.5213.01 2430MHz -3.0314.53 2440MHz -2.8914.75 2450MHz -2.7714.94 2460MHz -2.9514.72 2470MHz -2.8415.24 2480MHz -2.5316.04 2490MHz -1.8917.60 2500MHz -1.0720.05 Efficiency Peak Gian 深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 5 - 2.2. 4极化方向 Phi=0 Phi=90 深圳市飞敏科技有限公司 ShenZhen City FeiMin Technology CO.,LTD. Tel: 86-0755-23035723 Fax: 86-0755-23036702 E-mail: [email protected] www.fmant.cn - 6 - Phi=180 2.2.6天线辐射3D图

ProjectNo.:18220WC301326Page1of1 Code:AB-RF-05-b AppendixI--TestSetupPhotograph PhotoofRadiationEmissionTest