2A4N3-YM-T13 in 1 Wireless Charger

ABS + Fabric For For For iWatch Watch wireless output:3W Earphone wireless output:5W This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. FCC Warning

Shenzhen You & Me Electronics Co.,LTD Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-9-18 FCC ID: 2A4N3-YM-T1 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Shenzhen You & Me Electronics Co.,LTD certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Shenzhen You & Me Electronics Co., LTD certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Applicant: Shenzhen You & Me Electronics Co., LTD Address: Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Contact Person: Fei zhang Tel.: +86 13534112600 Email: [email protected] Sincerely, Signature:

1/1 TO: Office Feder 7435 Colum US A Com p FRN:0 Conta Addre Telep Email EIN:9 This l a loca The U outlin § 2.9 Appl Com p Produ Grant FCC I Conta Addre Aven Telep Email The A Equip This Date Appl Title Signa US Age e of Enginee ral Commun 5 Oakland Mi mbia, MD 21 Agent for Se pany Name: 0033489683 act Name: Da ess: 1312 17 phone No: (9 l:market@clf 98-1720547 letter is to co al representa US Agent fo ned in the FC 11. icant: pany name:S uct Descriptio tee code:2A4 ID:2A4N3-YM act Name:fei ess: Room 40 ue Bantian S phone No: +8 l:63599936@ Applicant is pment Autho A greement e: 2023/07/ icant’s Nam :Project Ma ature ent for Se ering Techno ications Com lls Road 1046 ervice of Pr CLF Import a avid chen 7th Street #6 949) 254-256 fimportexpor onfirm that t ative on beha r Service of CC Equipmen Shenzhen Yo on: 3 in 1 W 4N3 M-T1 zhan g 01 4 th Floor Street, Longg 86 13534112 @qq.com aware of a rization Pro g t is valid un /24 me:fei zhang anager ervice of P ology mmission rocess: and Export L 692，Denver 65 rt.com the US Agent alf ofShenzhe Process is a nt Authorizat u & Me Elect ireless Charg r 2nd Buildin gang District, 2600 nd agrees to gram, Report ntil (Perman g Process L Limited r, CO 80202, t for Service en You & Me aware of and tion Program tronics Co.,LT ger ng, Yunchuan , Shenzhen, C o comply w t and Order F nently valid US Ag Title: Signa LETTER OF United State of Process a e Electronics d agrees to c , Report and TD ng Kuajing Pa China ith the req u FCC 22-84, a d). gent for Se Manager ature F ATTEST es accepts resp Co.,LTD. comply with d Order FCC ark, No.1012 uirements ou and clause § rvice of Pr o TATION onsibility to the require 22-84, and c 2, Banxuegan utlined in the 2.911. ocess’s Nam act as ments clause ng e FCC me:

第 1 页 PRODUCT SPECIFICATION FOR APPROVAL Two-dimensional four images A11 coil CUSTOMER PRODUCT NAME PART No. PRODUCT SPEC Sensitivity:6.3uH±10% Magnetic disc specifications:43.5*5.3*1Double groove Wire specification:0.08*105*10Ts/18mm adhesive tape for outgoing line October 7th, 2022 DATE VERSION REV 1.0 RevisionModified ContentPrincipleDateNote REV 1.0 first releaseXue Lei 2022-10-07 PREPARED BY CHECKED BY APPROVED BY Authorized signature & company chop Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen Shenzhen Chenxing Electronic Technology Co., Ltd Shenzhen Chenxing Electronic Technology Co., Ltd 第 2 页 SPECIFICATION 一、Product size Disk diameter A 43.5 ±0.5 mm Coil outer diameter B 42 ±1mm Coil inner diameter C 20 .5 ±0.5 mm Product thickness D <2.5 mm Outlet length E 18mm±3mm Solder length F 2-5 mm Magnetic disc opening diameter G 5±0.3 mm Magnetic disc thickness 1±0. 1m m Disk shape Circular double groove Adhesive thickness Ordinary double- sided adhesive Anti crushing black film without Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen 第 3 页 二、schematic diagram 三、Winding parameters TERMINALWIRETurnsWinding Direction SF silk covered wire 0.08*105P 10TsCCW 四、Electrical characteristics: TEMPERATURE:25±10°C, RELATIVE HUMIDITY:65±20% ITEMTERMINALSPECIFICATIONTEST FREQUENCYTEST EQUIPMENTS IND.S-F 6. 3uH ±10% 100KHz/1.0VLCZ METER1062B 五、 Product image Shenzhen Chenxing Electronic Technology Co., Ltd Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen 第 4 页 六、Packing： The size of pearl cotton is 35 * 24.5 * 6.2cm, and each pearl cotton has a total of 40 compartments. Each compartment contains 6 pieces of products, with a total of 240 pieces of products packed in three layers of pearl cotton per box; The size of the cardboard box is 36.5 * 25.5 * 21 CM, with each box containing 720 PCS of products. Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen Shenzhen Chenxing Electronic Technology Co., Ltd

Shenzhen Chenxing Electronic Technology Co,Ltd. Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen 第 1 页 PRODUCT SPECIFICATION FOR APPROVAL Two-dimensional four images Power Transmitter for Apple Watch CUSTOMER PRODUCT NAME PART No. PRODUCT SPEC Inductance Spec: 7.7uH±10% Shielding spec: KP24.5*2.6mm soft shielding with rubber Silk covered wire spec: 2 UEW/155 0.08*24*13Ts Segment Length: 9mm Double side Type: 3M 9448A Magnet Spec: 7.8*2mm Electroplating with Zinc April 12, 2023 DATE VERSION REV1.0 RevisionModified ContentPrincipleDateNote REV 1.0 first releaseXue Lei 2023-04-12 PREPARED BYCHECKED BYAPPROVED BY Authorized signature & company chop ShenzhenChenxingElectronicTechnologyCo,Ltd. Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen 第 2 页 SPECIFICATION 一、Product size ShieldingOuter DiameterMax ( A) 25 ±0.5 mm Shielding Thickness(B) 2.6 ±0.2 mm ShieldingOuter DiameterMin (C) 23.7 ±0. 4mm ShieldingInner Diameter(D) 21 ±0.5 mm InnerHole OuterDiameter(E) 13.5±0.2mm ShieldingCylinder Height(F) 2.3±0.25mm InnerHole InnerDiameter(H) 7.7 ±0. 4mm Pin Length(I)3.0 ±0. 2m m SegmentLength(J)9m m±2mm MagnetSpec7.8*2.0±0. 1m m AdhesiveTape3M 9448A Shenzhen Chenxing Electronic Technology Co,Ltd. Company Name: Shenzhen Chenxing Electronic Technology Co., Ltd Factory address: 5th floor, Building 1, Xinkecheng Science and Technology Industrial Park, No. 51 Dabao Road, Xin'an Street, Bao'an District, Shenzhen 第 3 页 二、schematic diagram 三、Winding parameters TERMINALWIRETurnsWinding Direction SF silk covered wire 0.08*24P 13TsCCW 四、Electrical characteristics： TEMPERATURE:25±10°C, RELATIVE HUMIDITY:65±20% ITEMTERMINALSPECIFICATIONTEST FREQUENCYTEST EQUIPMENTS IND.S-F 7.7uH±10% 100KHz/1.0VLCZ METER 1062B

Shenzhen You & Me Electronics Co.,LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 18, 2023 Subject; Request for Confidentiality FCC ID: 2A4N3-YM-T1 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Fei zhang Title: Manager

Sept. 18,2023 Shenzhen You & Me Electronics Co.,LTD Model difference statement We Shenzhen You & Me Electronics Co.,LTD Of Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Declare under our sole responsibility that the product Product: 3 in 1 Wireless Charger Model Number: YM-T2, YM-T3, YM- T5, YM-T6, YM-T7, YM-T8, YM-T9 Except for the model and appearance color, all models have the same circuit and module. Thanks Sincerely, Fei zhang / Manager E-mail: : [email protected] Phone: +86 13534112600 Fax: +86 13534112600 Address : Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen You & Me Electronics Co.,LTD Date：Sept. 18, 2023 Product Model Number: 3 in 1 Wireless Charger FCC ID：2A4N3-YM-T1 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: Manager Email: [email protected] Telephone: +86 13534112600 On behalf of: Shenzhen You & Me Electronics Co.,LTD

Ext Photos Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

Label and Label Location Labe Label Location F C C I D F C C

Int Photos Photo 1 Photo 2 Photo 3 Photo 4 Air pods: ANT Phone : ANT Watch : ANT Photo 5 Photo 6 Photo 7

- Page 1 of 12 - Report No.: HB20230725002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product： 3 in 1 Wireless Charger Trade Mark: N/A Model Number： YM-T1 FCC ID： 2A4N3-YM-T1 Prepared for Shenzhen You & Me Electronics Co.,LTD Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 12 - Report No.: HB20230725002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 7 2.1 TEST LABORATORY ..................................................................................................................................................... 7 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 7 2.4 TEST SOFTWARE ........................................................................................................................................................ 7 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 8 4 RF EXPOSURE..................................................................................................................................................... 9 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 9 4.1.1. Limit ............................................................................................................................................................ 9 4.1.2. Test Procedures ........................................................................................................................................... 9 4.1.3. Test Setup .................................................................................................................................................. 10 4.1.4. Test Result ................................................................................................................................................. 10 5 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................12 - Page 3 of 12 - Report No.: HB20230725002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen You & Me Electronics Co.,LTD Address ................................. : Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Manufacturer's Name .......... : Shenzhen You & Me Electronics Co.,LTD Address ................................. : Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Product description Product name ........................ : 3 in 1 Wireless Charger Model Number ....................... : YM-T1 Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ..................... : KDB 680106 D01 RF Exposure Wireless Charging Apps v03r01 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Jul. 25. 2023~Sept. 04. 2023 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 12 - Report No.: HB20230725002E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755…

Text truncated - open the document above for the full version.

- Page 1 of 31 - Report No.: HB20230725002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product： 3 in 1 Wireless Charger Trade Mark: N/A Model Number： YM-T1 FCC ID： 2A4N3-YM-T1 Prepared for Shenzhen You & Me Electronics Co.,LTD Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 31 - Report No.: HB20230725002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 6 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................... 7 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 8 4 LIST OF TEST EQUIPMENT .................................................................................................................................. 9 5 TEST ITEM AND RESULTS ...................................................................................................................................11 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 11 5.2 CONDUCTED EMISSION ............................................................................................................................................. 12 5.3 RADIATED EMISSION ................................................................................................................................................ 16 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 21 6 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................23 7 PHOTOGRAPHS OF THE EUT..............................................................................................................................25 - Page 3 of 31 - Report No.: HB20230725002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen You & Me Electronics Co.,LTD Address ................................. : Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Manufacturer's Name .......... : Shenzhen You & Me Electronics Co.,LTD Address ................................. : Room 401 4 th Floor 2nd Building, Yunchuang Kuajing Park, No.1012, Banxuegang Avenue Bantian Street, Longgang District, Shenzhen, China Product description Product name ........................ : 3 in 1 Wireless Charger Model Number ....................... : YM-T1 Standards ............................. : FCC Part 15C Test procedure ..................... : ANSI C63.4: 2014 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Jul. 25. 2023~Sept. 04. 2023 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 31 - Report No.: HB20230725002E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Co…

Text truncated - open the document above for the full version.

- Page 1 of 2 - Test Setup Photos Radiated Emission Below 30MHz Radiated Emission Above 30MHz - Page 2 of 2 - Conducted emission MPE