2A5DA-PLYR-GOBluetooth Speaker

(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux RSS sans licence d’Industrie Canada. L’exploitation est soumise aux deux conditions suivantes : (1) Ce dispositif ne peut causer d'interférences ; et (2) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0 cm between the radiator and your body. Cet équipement est conforme aux limites d'exposition aux radiations FCC/ISED établies pour un environnement non contr?lé. Cet équipement doit être installé et utilisé avecune distance minimale de 0 cm entre le radiateur et votre corps FCC Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED Statement: This device complies with Industry Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: Radiation Exposure statement PMN: Bluetooth Speaker

FCC ID: 2A5DA-PLYR-GO IC: 28315-PLYRGO

FCC ID: 2A5DA-PLYR-GO IC: 28315-PLYRGO Bluetooth antenna

RF Exposure evaluation FCC ID: 2A5DA-PLYR-GO 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure requirement KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance GFSK Channel Channel 00 Channel 39 Channel 78 Target (dBm) 0.0 0.0 0.0 Tolerance ±(dB) 1.0 1.0 1.0 π/4DQPSK Channel Channel 00 Channel 39 Channel 78 Target (dBm) 1.0 1.0 1.0 Tolerance ±(dB) 1.0 1.0 1.0 8DPSK Channel Channel 00 Channel 39 Channel 78 Target (dBm) 1.0 1.0 1.0 Tolerance ±(dB) 1.0 1.0 1.0 BLE_1Mbps Channel Channel 00 Channel 19 Channel 39 Target (dBm) 0.0 0.0 0.0 Tolerance ±(dB) 1.0 1.0 1.0 BLE_2Mbps Channel Channel 00 Channel 19 Channel 39 Target (dBm) 0.0 0.0 0.0 Tolerance ±(dB) 1.0 1.0 1.0 2. E v a l u a t i o n R e s u l t Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW BT 2.480 5 2 1.585 0.5<3.0 Yes 3. C o n c l u s i o n The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06, No SAR is required. .....................End.........................

Antenna Describe Antenna PCB Antenna Gain 2.56dBi Frequency Range 2.4Ghz-2.483Ghz Connector Type Direct Location of mearement(company SHENZHENSHIXINZHONGXN name) TECHNOLOGY.CO.,LTD 2：External View Drawing Picture of antenna 3：Measurement Result 3.1 Return Loss (S11 ) 3.2 Smith Chart 3.3 Gain

FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1. Bandwidth 1.1 OBW 1.1.1 Test Result Mode TX Type Frequency (MHz) ANT 99% Occupied Bandwidth (MHz) Verdict Result Limit 1M SISO 2402 1 1.053 / Pass 2440 1 1.053 / Pass 2480 1 1.054 / Pass 2M SISO 2402 1 2.047 / Pass 2440 1 2.047 / Pass 2480 1 2.045 / Pass FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1.1.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_MCH_2440MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1.2 6dB BW 1.2.1 Test Result Mode TX Type Frequency (MHz) ANT 6dB Bandwidth (MHz) Verdict Result Limit 1M SISO 2402 1 0.711 >=0.5 Pass 2440 1 0.703 >=0.5 Pass 2480 1 0.713 >=0.5 Pass 2M SISO 2402 1 1.175 >=0.5 Pass 2440 1 1.176 >=0.5 Pass 2480 1 1.173 >=0.5 Pass FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1.2.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_MCH_2440MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2. Maximum Peak Conducted Output Power 2.1 Power 2.1.1 Test Result Mode TX Type Frequency (MHz) Maximum Peak Conducted Output Power (dBm) Verdict ANT1 Limit 1M SISO 2402 0.14 <=30 Pass 2440 0.52 <=30 Pass 2480 0.77 <=30 Pass 2M SISO 2402 0.04 <=30 Pass 2440 0.48 <=30 Pass 2480 0.65 <=30 Pass Note1: Antenna Gain: Ant1: 2.56dBi; FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2.1.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_MCH_2440MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2.2 EIRP 2.2.1 Test Result Mode TX Type Frequency (MHz) E.I.R.P (dBm) Verdict ANT1 Limit 1M SISO 2402 2.70 <=36.02 Pass 2440 3.08 <=36.02 Pass 2480 3.33 <=36.02 Pass 2M SISO 2402 2.60 <=36.02 Pass 2440 3.04 <=36.02 Pass 2480 3.21 <=36.02 Pass Note1: Antenna Gain: Ant1: 2.56dBi; Note2: E.I.R.P = Measured Power + Antenna Gain FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 3. Maximum Power Spectral Density 3.1 PSD 3.1.1 Test Result Mode TX Type Frequency (MHz) Maximum PSD (dBm/3kHz) Verdict ANT1 Limit 1M SISO 2402 -15.96 <=8 Pass 2440 -15.78 <=8 Pass 2480 -15.26 <=8 Pass 2M SISO 2402 -19.49 <=8 Pass 2440 -20.31 <=8 Pass 2480 -18.97 <=8 Pass Note1: Antenna Gain: Ant1: 2.56dBi; FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 3.1.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_MCH_2440MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 4. Unwanted Emissions In Non-restricted Frequency Bands 4.1 Ref 4.1.1 Test Result Mode TX Type Frequency (MHz) ANT Level of Reference (dBm) 1M SISO 2402 1 -1.46 2440 1 -0.76 2480 1 -0.55 2M SISO 2402 1 -1.87 2440 1 -1.28 2480 1 -1.02 Note1: Refer to RSS-247 Issue 2 section 5.5 and ANSI C63.10-2013, the channel contains the maximum PSD level was used to establish the reference level. FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 4.1.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_MCH_2440MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 4.2 CSE 4.2.1 Test Result Mode TX Type Frequency (MHz) ANT Level of Reference (dBm) Limit (dBm) Verdict 1M SISO 2402 1 -0.55 -20.55 Pass 2440 1 -0.55 -20.55 Pass 2480 1 -0.55 -20.55 Pass 2M SISO 2402 1 -1.02 -21.02 Pass 2440 1 -1.02 -21.02 Pass 2480 1 -1.02 -21.02 Pass Note1: Refer to RSS-247 Issue 2 section 5.5 and ANSI C63.10-2013, the channel contains the maximum PSD level was used to establish the reference level. FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 4.2.2 Test Graph 1M_LCH_2402MHz_Ant1_NTNV 1M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_MCH_2440MHz_Ant1_NTNV 1M_HCH_2480MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 1M_HCH_2480MHz_Ant1_NTNV 2M_LCH_2402MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_LCH_2402MHz_Ant1_NTNV 2M_MCH_2440MHz_Ant1_NTNV FCC ID:2A5DA-PLYR-GO IC:28315-PLYRGO 2M_HCH_2480MHz_Ant1_NTNV 2M_HCH_2480MHz_Ant1_NTNV

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 E-mail: [email protected] TEST REPORT FCC PART 15 SUBPART C 15.247 & RSS-247 Report Reference No. ................. : CTL2311107041-WF02 Compiled by: ( position+printed name+signature) Happy Guo (File administrators) Tested by: ( position+printed name+signature) Gary Gao (Test Engineer) Approved by: ( position+printed name+signature) Ivan Xie (Manager) Product Name .............................. : Bluetooth Speaker Model/Type reference ................. : PLAYERGO List Model(s) ................................ : N/A Trade Mark ................................... : Blue Tees, Blue Tees Golf FCC ID .......................................... : 2A5DA-PLYR-GO Applicant’s name ........................ : Blue Tees Enterprises, LLC Address of applicant .................. : 1990 N. California Blvd., Suite 20, PMB 1111, Walnut Creek, California, United States 94596 Test Firm ...................................... : Shenzhen CTL Testing Technology Co., Ltd. Address of Test Firm .................. : Floor 1-A, Baisha Technology Park, No.3011, Shahexi Road, Nanshan District, Shenzhen, China 518055 Test specification ........................ : Standard ....................................... : 47 CFR FCC Part 15 Subpart C 15.247 RSS-247 Issue 2, February 2017 TRF Originator .............................. : Shenzhen CTL Testing Technology Co., Ltd. Master TRF ................................... : Dated 2011-01 Date of receipt of test item ......... : Dec. 04, 2023 Date of sampling ......................... : Dec. 05, 2023 Date of Test Date ......................... : Dec. 06, 2023 - Dec. 12, 2023 Date of Issue ................................ : Dec. 13, 2023 Result ........................................... : Pass Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. V1.0 Page 2 of 31 Report No.: CTL2311107041-WF02 TEST REPORT Test Report No. : CTL2311107041-WF02 Dec. 13, 2023 Date of issue Equipment under Test : Bluetooth Speaker Sample No. : CTL2311107041 Model /Type : PLAYERGO Listed Models : N/A Applicant : Blue Tees Enterprises, LLC Address : 1990 N. California Blvd., Suite 20, PMB 1111, Walnut Creek, California, United States 94596 Manufacturer : Blue Tees Enterprises, LLC Address : 1990 N. California Blvd., Suite 20, PMB 1111, Walnut Creek, California, United States 94596 Test result Pass * * In the configuration tested, the EUT complied with the standards specified page 5. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the issuing testing laboratory. V1.0 Page 3 of 31 Report No.: CTL2311107041-WF02 ** Modified History ** Revisions Description Issued Data Report No. Remark Version 1.0 Initial Test Report Release 2023-12-13 CTL2311107041-WF02 Tracy Qi V1.0 Page 4 of 31 Report No.: CTL2311107041-WF02 Table of Contents Page 1. SUMMARY............................................................................................................................................................ 5 1.1. TEST STANDARDS ..................................................................................................................................................... 5 1.2. TEST DESCRIPTION ........................................................................................................................................................ 5 1.3. TEST FACILITY .............................................................................................................................................................. 6 1.4. STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................................... 6 2. GENERAL INFORMATION ....................................................................................................................................... 8 2.1. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 8 2.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 8 2.3. DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 8 2.4. EQUIPMENTS USED DURING THE TEST .............................................................................................................................. 9 2.5. RELATED SUBMITTAL(S) / GRANT (S) .............................................................................................................................. 10 2.6. MODIFICATIONS ......................................................................................................................................................... 10 3. TEST CONDITIONS AND RESULTS ......................................................................................................................... 11 3.1. CONDUCTED EMISSIONS TEST ....................................................................................................................................... 11 3.2. RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 14 3.3. MAXIMUM CONDUCTED OUTPUT POWER .................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2A5DA-PLYR-GO IC: 28315-PLYRGO