2A5H8-M1Long Distance Touch lamps

Step 1 Scan the QR code to download the app (iPhone & Android) Step 2 Scan the QR code on the lamp and add the lamp Step 3 Set the WIFI of the lamp for distribution network 1. Connect your phone to the WIFI at home 2. Open the distribution network interface on the app Step 4 Enter the WIFI password at home Step 5 Press the power button of the lamp and wait for the light to flash red Step 6 Press the Setup button on the App interface to enter the intelligent distribution network process This process requires patience. Once the network is successfully connected, the lights will automatically connect to WIFI and flash white three times. If the network configuration is unsuccessful multiple times, please modify the WIFI router at home to 2.4G network mode Customer Service: [email protected] Long Distance Touch lamps m1 Step 6 Operating instructions for the lamp Customer Service: [email protected] Press to turn on the power, press again to turn off the power Charging interface.Charging requires turning on the power source of the lamp Insert the lamp post into the wine bottle Touch for 3 seconds or more to turn on or off the lights. Note that it is only a light switch, not a power on or off switch Touch once to change the color. Your friend's light also changes color synchronously Step 7 Particular attention Every time the lamp is turned on, it automatically connects to the WIFI network and flashes white three times upon successful connection.The networking time ranges from 10 to 90 seconds, depending on the frequency band of the router. If you encounter multiple unsuccessful connections for a long time, please restart the WIFI router. If your WIFI router at home is in the 5G frequency band, the light networking will be slow. Please set it to 2.4G frequency band or be compatible with 2.4G frequency band. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Shen Zhen Shi Pulomi Trading Co.. Ltd Covered Equipment Certification Attestation Letter 10/27/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2A5H8-M1 Shen Zhen Shi Pulomi Trading Co.. Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shen Zhen Shi Pulomi Trading Co.. Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shen Zhen Shi Pulomi Trading Co.. Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). <Signature>: Name: Yanwei Zeng Title: Manager Company: Shen Zhen Shi Pulomi Trading Co.. Ltd Date: 10/27/2025

Shen Zhen Shi Pulomi Trading Co.. Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 10/27/2025 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2A5H8-M1 FRN of applicant: 0037627833 Per section 2.911(d)(7) of the FCC rules, [Shen Zhen Shi Pulomi Trading Co.. Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Herland International Trading Inc FCC Registration Number (FRN): 0036324101 Physical U.S. Company Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Contact Person: Jianfeng Gao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Yanwei Zeng Title: Manager Company Name: Shen Zhen Shi Pulomi Trading Co.. Ltd Date: 10/27/2025 Agent Signed (if different from Applicant): Signed: Printed name: Jianfeng Gao Title: Manager Company Name: Herland International Trading Inc Date: 10/27/2025

Shen Zhen Shi Pulomi Trading Co.. Ltd 2025-10-27 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A5H8-M1 Product Name: Long Distance Touch lamps Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>: Name: Yanwei Zeng Title: Manager Company: Shen Zhen Shi Pulomi Trading Co.. Ltd

Shen Zhen Shi Pulomi Trading Co.. Ltd 2025-10-27 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen DL Testing Technology Co., Ltd.（101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China）to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shen Zhen Shi Pulomi Trading Co.. Ltd（19E, South Block, Dongfang Palace Building, Nanhu Road, Nanhu Street, Luohu District, Shenzhen） <Signature>: Name: Yanwei Zeng Title: Manager Company: Shen Zhen Shi Pulomi Trading Co.. Ltd

Shen Zhen Shi Pulomi Trading Co.. Ltd 2025-10-27 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature>: Name: Yanwei Zeng Title: Manager Company: Shen Zhen Shi Pulomi Trading Co.. Ltd

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size:26*22mm M/N: m1 FCC ID: 2A5H8-M1 Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) ANT Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

FCC ID: 2A5H8-M1 RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in KDB 447498 D01 V06 and 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation wifi 2.4G mode Channel Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 12.63 18.3231 0.0051 1.0 PASS 802.11g 10.11 10.2565 0.0029 1.0 PASS 802.11n HT20 9.62 9.1622 0.0026 1.0 PASS 802.11n HT40 9.59 9.0991 0.0026 1.0 PASS Remark: antenna gain=1.5dBi

AN9520 Multilayer Chip Antenna for 2.4GHz Wireless Communication RainSun Corporation http://www.rainsun.com 1of 9 Aug, 2009 Ver.2.3 AN9520 Multilayer Chip Antenna ◆Features yLight weight and low profile 9.5mm(L)X2.1mm(W)X1.0mm(H) yOmni‐directional in azimuth Lead (Pb) Free ◆Applicationspp y2.4GHz wireless communications y2.4GHz Modules yBluetooth System 802.11b/g Wireless LAN System Specifications Center frequency2.45GHz Peak gain Operation temperature Storage temperature VSWR Input Impedance 1.5dBi ‐40 ~ +85 ̊C ‐40 ~ +85 ̊C 2.0 (max) 50 Ohm Power handling Bandwidth Azimuth beamwidth Polarization 3W (max) 200MHz Omni‐directional Linear RainSun Corporation http://www.rainsun.com 2of 9 Aug, 2009 Ver.2.3 Pin configuration Pin NoPin assignment 1 Top view 1Feed termination 2Feed point mark 3Solder termination 2 Dimensions 3 SymbolDimensions(mm) A 9.50 ±0.10 B 2.10 ±0.10 C 0.65 ±0.05 H 1.00 ±0.20 PCB foot printerp RainSun Corporation http://www.rainsun.com 3of 9 Aug, 2009 Ver.2.3 Recommended Test Board Pattern Top view Bottom view Ground Plane 50 Ohm Transmission line Board thickness : 0.6mm Board material : FR4 Unit : mm SMA connector Fig-1 Testing Setup Measurement Testing Instrument: Anritsu 37369C VNA(Vector Network Analyzer)Analyzer) VNA calibrate with 1 path reflection only calibration sequence on test board feed point. Thetestboarddimensionandit’s RainSun Corporation http://www.rainsun.com 4of 9 Aug, 2009 Ver.2.3 The test board dimension and it s layout is the same as Fig‐1. Return loss Typical Electrical Characteristics Smith Chart Marker data: 1:f 2 567GHz1 : f=2.567 GHz 2 : f=2.365 GHz 3 : f=2.447 GHz RainSun Corporation http://www.rainsun.com 5of 9 Aug, 2009 Ver.2.3 Typical Radiation Patterns 2.45 GHz H‐Plane 2.45 GHz E‐Plane RainSun Corporation http://www.rainsun.com 6of 9 Aug, 2009 Ver.2.3 Typical Soldering Profile for Lead‐free Process ) 340°C Peak temp 340°C Temperature ( °C ) 300°C 150°C 25 sec. 5 sec. Pre-heating Time (sec.) Do not exceed 30 secs. 260°C 10 sec, max Reflow Soldering e mperature ( °C ) 260°C 230°C 180°C T e 60 sec. 30 sec. Pre-heating RainSun Corporation http://www.rainsun.com 7of 9 Aug, 2009 Ver.2.3 Time (sec.) Packing Blister Tape Specifications SymbolDimension ToleranceUnit W16.00 ±0.30 mm E1.75 ±0.10 mm F7.50 ±0.10 mm D1.50 + 0.10 ‐0.00 mm D 1 1.50 + 0.25 ‐0.00 mm P 0 4.00 ±0.10 mm P8.00 ±0.10 mm P 2 2.00 ±0.10 mm A 0 2.20 ±0.10 mm B 0 10.00 ±0.10 mm K120 ±010 RainSun Corporation http://www.rainsun.com 8of 9 Aug, 2009 Ver.2.3 K 0 1.20 ±0.10 mm t0.30 ±0.05 mm Reel Specifications Quantity l Tape Width () A () C () B () E () W () W 1 ()Per Reel(mm)(mm)(mm)(mm)(mm)(mm)(mm) 1,50016 180±1 13.0±0.5 62±0.5 2.2±0.5 16±0.5 20±0.2 RainSun Corporation http://www.rainsun.com 9of 9 Aug, 2009 Ver.2.3

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251014037R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 48 FCC Part 15C Test Report FCC ID: 2A5H8-M1 Applicant: Shen Zhen Shi Pulomi Trading Co., Ltd Address: 19E, South Block, Dongfang Palace Building, Nanhu Road, Nanhu Street, Luohu District, Shenzhen Manufacturer: Shen Zhen Shi Pulomi Trading Co., Ltd Address: 19E, South Block, Dongfang Palace Building, Nanhu Road, Nanhu Street, Luohu District, Shenzhen Product Name: Long Distance Touch lamps Trade Mark: N/A Model Number: m1 Date of Receipt: Oct. 14, 2025 Test Date: Oct. 14, 2025 - Oct. 23, 2025 Date of Report: Oct. 23, 2025 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-251014037R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251014037R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 48 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 MEASUREMENT UNCERTAINTY 4 2 . GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 DESCRIPTION OF TEST MODES 6 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3 . EMC EMISSION TEST 9 3.1 CONDUCTED EMISSION MEASUREMENT 9 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2 TEST PROCEDURE 9 3.1.3 DEVIATION FROM TEST STANDARD 9 3.1.4 TEST SETUP 10 3.1.5 EUT OPERATING CONDITIONS 10 3.1.6 TEST RESULTS 10 3.2 RADIATED EMISSION MEASUREMENT 13 3.2.1 RADIATED EMISSION LIMITS 13 3.2.2 TEST PROCEDURE 14 3.2.3 DEVIATION FROM TEST STANDARD 14 3.2.4 TEST SETUP 14 3.2.5 EUT OPERATING CONDITIONS 15 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8 TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 23 3.3.1 TEST REQUIREMENT: 23 3.3.2 TEST PROCEDURE 23 3.3.3 DEVIATION FROM TEST STANDARD 23 3.3.4 TEST SETUP 24 3.3.5 EUT OPERATING CONDITIONS 24 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 29 3.4.1 APPLICABLE STANDARD 29 3.4.2 TEST PROCEDURE 29 3.4.3 DEVIATION FROM STANDARD 29 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251014037R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 48 Table of Contents Page 3.4.4 TEST SETUP 29 3.4.5 EUT OPERATION CONDITIONS 29 3.4.6 TEST RESULTS 29 4 . AVERAGE OUTPUT POWER 34 4.1 APPLIED PROCEDURES / LIMIT 34 4.1.1 TEST PROCEDURE 34 4.1.2 DEVIATION FROM STANDARD 34 4.1.3 TEST SETUP 34 4.1.4 EUT OPERATION CONDITIONS 34 4.1.5 TEST RESULTS 35 5 . POWER SPECTRAL DENSITY TEST 38 5.1 APPLIED PROCEDURES / LIMIT 38 5.1.1 TEST PROCEDURE 38 5.1.2 DEVIATION FROM STANDARD 38 5.1.3 TEST SETUP 38 5.1.4 EUT OPERATION CONDITIONS 38 5.1.5 TEST RESULTS 39 6 . 6DB BANDWIDTH TEST 42 6.1 APPLIED PROCEDURES / LIMIT 42 6.1.1 TEST PROCEDURE 42 6.1.2 DEVIATION FROM STANDARD 42 6.1.3 TEST SETUP 42 6.1.4 EUT OPERATION CONDITIONS 42 6.1.5 TEST RESULTS 43 7 . ANTENNA REQUIREMENT 48 7.1 STANDARD REQUIREMENT 48 7.2 EUT ANTENNA 48 8 . TEST SEUUP PHOTO 48 9 . EUT PHOTO 48 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251014037R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 48 1.. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.205, 15.209, 15.247(d) Radiated Spurious Emission PASS 15.209, 15.205 Band Edge Emission PASS 15.247(d) Conducted Spurious Emissions PASS 15.247(b) Average Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2% 9 Power Spectral Density ±2.45dBm Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251014037R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 48 2.. GENERAL INFORMATION 2.1. GENERAL DESCRIPTION OF EUT Product Name: Long Distance Touch lamps Trade Mark: N/A Model Number: m1 Test Model: m1 Sample number: 251014037-01 Model Difference N/A Operation Frequency: 2412~2462 MHz for 802.11b/g/nHT20 2422~2452 MHz for 802.11nHT40 Channel numbers: 11 Channels for 802.11b/g/n(HT20) 7 channels for 802.11nHT40 Channel separation: 5MHz Modulation technology: 802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g/n(20/40): OFDM(QPSK, BPSK, 16-QAM, 64-QAM) Rate of Transmitter 802.11b: 11/5.5/2/1Mbps 802.11g: 54/4…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. Conducted Measurement Photos ※※※※※ END OF REPORT ※※※※※