2A5YG-WQ253 in 1 Magnetic Wireless Charger

25W 9V/3A,12V3A,15V3A 60*70*70mm 25W Indicator light The charging area for the watch can be retracted by pressing and releasing. Input interface. Charging instructions. 1. Power up: Use an adapter with a voltage of 9V, 12V, or 15V to power the product. 2. Place the device: Simply place the device you want to charge in the corresponding location and start the charging process. Indicator instructions. PatternIndicator Power on Idle Charging Detected foreign object. The indicator light blinks three times and then goes out The indicator light is off The indicator light remains on The indicator light blinks. Notes: This product is compatible with devices featuring built-in wireless charging capabilities. For non-magnetic phone models, please add a magnetic ring before using this product. Input compatibility: QC3.0, PD3.0 protocols (recommended PD45W). When the input exceeds 12V = 3A, the maximum charging power for a phone is 25W. When the input exceeds 15V = 3A, it can simultaneously charge a phone at 25W, a headset at 5W, and a watch at 2.5W. The maximum charging power for iPhone series is 25W, for Samsung phones it is 15W, and for Huawei/Android phones it is 5W. Do not place the wireless charger too close to magnetic strips or chips (e.g., ID cards, bank cards) to prevent the magnetic cards from becoming invalid. Use a 9V adapter for powering the device. (Using a 5V adapter may result in interrupted charging due to insufficient power.) Since the wireless charger generates some energy losses during the transmission of power, a portion of the energy is converted into heat. Mild heating during charging is normal. The wireless charger is equipped with a temperature sensor. If the temperature during charging becomes excessively high, the charging process will automatically stop, and charging will resume once the charging device or the wireless charger has cooled down. Avoid excessively squeezing or bumping the device. Keep the surface of the charger dry and do not place the product in a fire or humid environment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

Shenzhen Midason Technology Co.,Ltd Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2026/06/10 U.S. Agent Designation Shenzhen Midason Technology Co.,Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A5YG-WQ25): Name and company of U.S. agent: GLOCERTS TECHNOLOGY INC Physical U.S. address of agent: 19784 SUNKISSED RIDGE DR RIVERSIDE, CA 92507 United States FRN of U.S. agent: 0036339737 Phone of U.S. agent: (626) 588-8039 Email address of U.S. agent: [email protected] GLOCERTS TECHNOLOGY INC acknowledges their obligation to accept service of process on behalf of Shenzhen Midason Technology Co.,Ltd with the FRN [0032160616] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. An expiration date for this letter does not exist. Sincerely, Signature Frank Leng Manager Shenzhen Midason Technology Co.,Ltd Signature Huiying Fan Director GLOCERTS TECHNOLOGY INC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

FCC ID: 2A5YG-WQ25 External Photos of the EUT FCC ID: 2A5YG-WQ25 FCC ID: 2A5YG-WQ25

Label and Location Size: L: 2.0cm*W: 1.0cm Label and Location FCC ID: 2A5YG-WQ25

FCC ID: 2A5YG-WQ25 Internal Photos of the EUT FCC ID: 2A5YG-WQ25 FCC ID: 2A5YG-WQ25 FCC ID: 2A5YG-WQ25 FCC ID: 2A5YG-WQ25 Watch Coil Antenna FCC ID: 2A5YG-WQ25 FCC ID: 2A5YG-WQ25 Earbuds Coil Antenna FCC ID: 2A5YG-WQ25 Phone Coil Antenna

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn RF Exposure-WPT Report Reference No. ..................... : FCC ID............................................. : CTA26060201102 2A5YG-WQ25 Compiled by ( position+printed name+signature) . : File administrators Zoey Cao Supervised by ( position+printed name+signature) . : Project Engineer Ace Chai Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Jun. 07, 2026 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Applicant’s name ............................ : Shenzhen Midason Technology Co.,Ltd Address............................................ : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Test specification ........................... : FCC CFR 47 PART 1, § 1.1310 Standard ........................................... : KDB 680106 D01 Wireless Power Transfer v04 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : 3 in 1 Magnetic Wireless Charger Trade Mark ....................................... : N/A Manufacturer .................................... : Shenzhen Midason Technology Co.,Ltd Model/Type reference ...................... : WQ25 Listed Models .................................. : N/A Rating ............................................... : Input: 9V3A,12V3A,15V3A Wireless output: Phone Output: 25W/15W/10W/7.5W/5W Watch Output: 2.5W Earphone Output: 3W Result ............................................... : PASS Report No.: CTA26051901102 Page 2 of 10 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : 3 in 1 Magnetic Wireless Charger Model /Type : WQ25 Listed Models : N/A Applicant : Shenzhen Midason Technology Co.,Ltd Address : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Manufacturer : Shenzhen Midason Technology Co.,Ltd Address : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA26051901102 Page 3 of 10 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 TEST STANDARDS ............................................................................................................ 4 2 SUMMARY .......................................................................................................................... 5 2.1 General Remarks ..................................................................................................... 5 2.2 Product Description ................................................................................................. 5 2.3 Description of the test mode .................................................................................... 5 2.4 Special Accessories ................................................................................................. 5 2.5 Modifications ............................................................................................................ 5 3 TEST ENVIRONMENT ....................................................................................................... 6 3.1 Address of the test laboratory .................................................................................. 6 3.2 Test Facility .............................................................................................................. 6 3.3 Statement of the measurement uncertainty ............................................................. 6 3.4 Equipments Used during the Test ........................................................................... 6 4 Test limit .............................................................................................................................. 7 4.1 Requirement ............................................................................................................ 7 4.2 Test setup ................................................................................................................ 8 4.3 Test Procedures....................................................................................................... 9 4.4 Equipment Approval Considerations of KDB 680106 D01v04 ................................ 9 4.5 Test results .............................................................................................................. 9 4.6 Conclusion .....................................................................................…

Text truncated - open the document above for the full version.

1. Antenna Description: Antenna type Loop coil antenna Model WQ25-1 Frequency range 110KHz - 205KHz Manufacturer Shenzhen Midason Technology Co.,Ltd Address Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China ANT Peak Gain 0dBi 2. Antenna Photo: We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required.

1. Antenna Description: Antenna type Loop coil antenna Model WQ25-2 Frequency range 110KHz - 205KHz Manufacturer Shenzhen Midason Technology Co.,Ltd Address Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China ANT Peak Gain 0dBi 2. Antenna Photo: We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required.

1. Antenna Description: Antenna type Loop coil antenna Model WQ25-3 Frequency range 110KHz - 205KHz Manufacturer Shenzhen Midason Technology Co.,Ltd Address Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China ANT Peak Gain 0dBi 2. Antenna Photo: We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required.

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC PART 15 SUBPART C TEST REPORT Report Reference No. ..................... : FCC ID............................................. : CTA26060201101 2A5YG-WQ25 Compiled by ( position+printed name+signature) . : File administrators Zoey Cao Supervised by ( position+printed name+signature) . : Project Engineer Ace Chai Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Jun. 07, 2026 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen Midason Technology Co.,Ltd Address............................................ : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Test specification ........................... : Standard ........................................... : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10-2020+Cor. 1-2023+C63.10a-2024 + Errata to C63.10a- 2024 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : 3 in 1 Magnetic Wireless Charger Trade Mark ....................................... : N/A Manufacturer .................................... : Shenzhen Midason Technology Co.,Ltd Model/Type reference ...................... : WQ25 Listed Models .................................. : N/A Modulation Type ............................... : ASK Operation Frequency ........................ : From 110KHz~205KHz Rating ............................................... : Input: 9V3A,12V3A,15V3A Wireless output: Phone Output: 25W/15W/10W/7.5W/5W Watch Output: 2.5W Earphone Output: 3W Result ............................................... : PASS Report No.: CTA26051901101 Page 2 of 31 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : 3 in 1 Magnetic Wireless Charger Model /Type : WQ25 Listed Models : N/A Applicant : Shenzhen Midason Technology Co.,Ltd Address : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Manufacturer : Shenzhen Midason Technology Co.,Ltd Address : Foor 2,Building A, NO.10,Alley 4, Rd., Shaxin, St. Maluan,District Pingshan,Shenzhen China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA26051901101 Page 3 of 31 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S .................................................................. 4 2 S U M M A R Y ............................................................................. 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Description of the test mode 6 2.4 Special Accessories 6 2.5 Modifications 6 3 T E S T E N V I R O N M E N T ............................................................... 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N D I T I O N S A N D R E S U L T S ............................................ 11 4.1 AC Power Conducted Emission 11 4.2 Radiated Emission 14 4.3 The 20dB bandwidth 18 4.4 Antenna Requirement 19 5 T E S T S E T U P P H O T O S O F T H E E U T .......................................... 20 6 PH O T O S O F T H E E U T ............................................................. 21 Report No.: CTA26051901101 Page 4 of 31 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 15 Subpart C (Section 15.207): Conducted limits. FCC Rules and Regulations Part 15 Subpart C (Section 15.209): Radiated emission limits; general requirements. ANSI C63.10-2020+Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024: American National Standard for Testing Unlicensed Wireless Devices Report No.: CTA26051901101 Page 5 of 31 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Jun. 02, 2026 Testing commenced on : Jun. 02, 2026 Testing concluded on : Jun. 07, 2026 …

Text truncated - open the document above for the full version.

FCC ID: 2A5YG-WQ25 Test Setup Photos of the EUT