2A65SDRONES2S3MINI LED DRONE

Mini LED Drone USER MANUAL DISCLAIMER AND SAFETY GUIDELINES 1. DO NOT look directly into the drone light. 2. DO NOT treat the product as household waste. 3. DO NOT fly above or near obstacles, crowds, open water, public road, high voltage power lines or trees. 4. DO NOT use the drone in severe weather conditions. These include wind, snow, rain, smog, hail, lightning, tornadoes or hurricanes. 5. Stay away from the rotating propellers and motors to avoid some tiny objects (e.g. hair) to get into them. 6. This drone does not come with GPS module. Please fly the drone within the control range. 7. Be sure to observe all local regulations, obtain appropriate authorizations and understand risks. Please note it is solely your responsibility to comply with all flight regulations. MAINTENANCE AND CARE 1. Thoroughly check the drone after crash or violent impact. 2. Do not charge battery before it cools down. 3. Remove the batteries if the product will not be in use for a long time. 4. Do not over charge the battery. Unplug the charger once it’s fully charged. 5. Store the drone and remote in a cool, dry place away form direct sunlight. 6. Do not charge the battery next to inflammables, such as carpet, timber floor etc., or on the surface of electro-conductive objects. Please always keep an eye on the battery while charging. 7. Please use the original battery provided. Use an incorrect type of battery may lead to fire hazards. 8. Do not dispose of the battery in fire or a hot oven, cut or mechanically crush the battery, as this may cause explosions. 9. Do not leave the battery in an extremely high-temperature environment taht can result in an explosion or the leakage of flammable liquid or gas. 10. Do not expose the battery to the extremely low air pressure, as this may resuly in an explosion or hte leakage of flammable liquid or gas. Note:Press and hold the One Key Take-off/Landing button for 3s to male an emergency stop. PRODUCT OVERVIEW Short press for changing speed / Long press for one key reverse function Left Control Stick (Press down for changing LED mode) One key Take-off / Landing Short press for 360° Flip, Long press for headless mode ON/OFF Right Control Stick (Press down for fine-tuning) Power Indicator HEAD TAIL LED Light Motor Battery Rotor Blade FLIGHT PREPARATION 1. Install the remote batteries. 3*1.5V AAA(batteries not included)Make sure the batteries have enough power. ON/OFF t 5V/1-2A 2. Charge the battery of the drone. 3. Install the drone battery after it’s fully charged. 4/ 9P$K  USB Adapter Power Bank USB Port Tips: 1. For your safety, please use the original batery and USB cable. 1.Turn on the drone (The LED light on the drone flashes rapidly) 4.Push the left control stick forward to top and then pull it backward till the bottom. Pairing is successful when the LED on the drone is solid on. 5.Move the left and right sticks inward & downward (left stick 5 o’clock and right stick 7 o’clock positions) for 3 seconds.The LED will flash quickly and then turns to solid, calibration is successfully. 2.Turn on the controller 3.Place the drone at a flat surface with head forward 2. Flight time of the battery may be reduced when flying in cold weathe 3. Free the battery of any sharp objects that could puncture into the battery to avoid risks of explosions and fire. 4. The LED on the drone will flash continously when the battery is low 5. To extend the battery’s lifespan, recharge it at least once every three months if not using it for long periods of time. Charging: Red LED Fully Charged: LED Off FLIGHT OPERATION GUIDE Note: Pls repeat the step 5 before every flight Connect the battery into the interface and slide it to the end. Option 1: Press the button to take off. Option 2: Move the Left Control Stick to lower left in 45° and the Right Control Stick to lower rightin 45° at the same time until four rotor blades start totating, then slowly push the Left Control Stick forward to take off. Take-off Option 1: Press the button to take off. Option 2: Pull the Left Control Stick backward to the bottom to land the drone, and hold it for 3s at least until all the rotor blades stop rotating. Landing Ascend and descend Push the Left Control Stick forward and the drone will ascend; pull it backward and the drone will descend. Push the Left Control Stick leftward and the drone will rotate to the left; pull it rightward and the drone will rotate to the right. Rotate Left and Rotate Right Instructions of the Remote Left Control Stick Forward and Backward Push the Right Control Stick forward and the drone will fly forward; pull it backward and the drone will fly backward. Push the Right Control Stick leftward and the drone will fly leftward; pull it rightward and the drone will fly rightward. Leftward and Rightward Right Control Stick This is one of the default setting in the drone. When you release the Left Control Stick after the ascending/descending action, the drone will hover at the current flight height. For a stable flight. press the trim buttons to adjust accordingly. Altitude Hold / Hover Flight Trimming If the drone drifts forward or backward when flying, press down the right stick once and then control the right stick forward or backward to adjust. If the drone drifts leftward or rightward when flying, press down the right stick once and then control the right stick left side or right side to adjust. After flying the drone to a height over 2 meters, press the 360 ° flip button to activate 360 ° flip function. Then move the Right Control Stick forward/backward/ leftward/rightward to flip the drone accordingly. 360 °Flip Forward Head Head Tail Tail Backward 2. Long press the right upper button to active headless function. You will heard 2 beeps. In this mode, the drone will fly following the direction of the Right Control Stick regardless of the positionof your drone’s head or the tail. The LED on the drone will flash during headless mode.Long press the same button aga…

Text truncated - open the document above for the full version.

ShantouChenghaiSystechToysCo.,Ltd LeChengBuilding,Huafu,GuangyiStreet,ChenghaiDistrict,ShantouCity,GuangdongProvince,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:08-02-2023 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2A65SDRONES2S3 [ShantouChenghaiSystechToysCo.,Ltd](“theapplicant”)certifiesthattheequipmentforwhich authorizationissoughtisnot“covered”equipmentprohibitedfromreceivinganequipment authorizationpursuanttosection2.903oftheFCCrules. Sincerely, (Applicantsignature) (SharlinZhuang)

ShantouChenghaiSystechToysCo.,Ltd LeChengBuilding,Huafu,GuangyiStreet,ChenghaiDistrict,ShantouCity,GuangdongProvince,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:08-02-2023 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2A65SDRONES2S3 [ShantouChenghaiSystechToysCo.,Ltd](“theapplicant”)certifiesthat,asofthedateofthefilingofthe application,theapplicantisnotidentifiedontheCoveredListasanentityproducing“covered” equipment. Sincerely, (Applicantsignature) (SharlinZhuang)

SHANTOU CHENGHAI SYSTECH TOYS CO.,LTD LeCheng Building, Huafu, Guangyi Street, Chenghai District, Shantou City, Guangdong Province China Date: 2023-07-11 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A65SDRONES2S3 US Agent – Attestation Statement / Part 2.911(d)(7) SHANT OU CHENGHAI SYSTECH TOYS CO.,LTD certifies, that as of 2023-07-11, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2A65SDRONES2S3. SHANTOU CHENGHAI SYSTECH TOYS CO.,LTD, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of SHANTOU CHENGHAI SYSTECH TOYS CO.,LTD for FCC ID: 2A65SDRONES2S3. Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: SHANTOU CHENGHAI SYSTECH TOYS CO.,LTD Designated Agent: FCC US Agent, LLC Company Representative:Sharlin Zhuang Designated Agent Representative: Tim Payne Signature: Signature:

Shantou Chenghai Systech Toys Co.,Ltd LeCheng Building, Huafu, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, China Aug.03, 2023 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID : 2A65SDRONES2S3 Model Number: S3, S1, S2, S5, S6, S7, S8, S9, S161, S162, S163, S165, S166, S167, S168, S169, TK102, TK103, TK105, TK106, TK107, TK108, TK109, DM001, DM002, DM003, DM005, DM007, DM008, DM009, DM101, DM102, DM103, DM105, DM106, DM107, DM108, DM109, F1, F2, F3, F5, F6, F7, F8, F9, NH320, NH330, NH525, NH530, NH760, C127 To Whom It May Concern: We, The SHANTOU CHENGHAI SYSTECH TOYS CO., LTD hereby declare that the models are identical except the model name. Except for the different above, no other modification is performed. Sincerely, Signature: Contact person: Sharlin Zhuang

Shantou Chenghai Systech Toys Co.,Ltd LeCheng Building, Huafu, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, China Agent Authorization Company: Shantou Chenghai Systech Toys Co.,Ltd Address: LeCheng Building, Huafu, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, China Product Name: MINI LED DRONE Model Number(s): S3, S1, S2, S5, S6, S7, S8, S9, S161, S162, S163, S165, S166, S167, S168, S169, TK102, TK103, TK105, TK106, TK107, TK108, TK109, DM001, DM002, DM003, DM005, DM007, DM008, DM009, DM101, DM102, DM103, DM105, DM106, DM107, DM108, DM109, F1, F2, F3, F5, F6, F7, F8, F9, NH320, NH330, NH525, NH530, NH760, C127 Product Description: MINI LED DRONE We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-08-03 Name: Sharlin Zhuang Company: SHANTOU CHENGHAI SYSTECH TOYS CO., LTD

ShantouChenghaiSystechToysCo.,Ltd LeChengBuilding,Huafu,GuangyiStreet,ChenghaiDistrict,ShantouCity,GuangdongProvince,China OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date: 2023-08-02 Subject;RequestforConfidentiality FCCID:2A65SDRONES2S3 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely Contactperson: SharlinZhuang

Report No.: AGC13923230701AP02 Page 1 of 4 EXTERNAL PHOTOS ALL VIEW OF EUT TOP VIEW OF EUT Report No.: AGC13923230701AP02 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC13923230701AP02 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC13923230701AP02 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 5mm&20mm FCC ID: 2A65SDRONES2S3

Report No.: AGC13923230701AP02 Page 1 of 3 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC13923230701AP02 Page 2 of 3 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC13923230701AP02 Page 3 of 3 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) ****************************************End of Report************************************* 2.4G Antenna

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2A65SDRONES2S3 Product Description MINI LED DRONE Model Name S3, S1, S2, S5, S6, S7, S8, S9, S161, S162, S163, S165, S166, S167, S168, S169, TK102, TK103, TK105, TK106, TK107, TK108, TK109, DM001, DM002, DM003, DM005, DM007, DM008, DM009, DM101, DM102, DM103, DM105, DM106, DM107, DM108, DM109, F1, F2, F3, F5, F6, F7, F8, F9, NH320, NH330, NH525, NH530, NH760, C127 Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others (2.4G: 2.446 GHz to 2.476GHz) Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. Output Power -0.508dBm Antenna Gain 0.17dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT Test Mode Channel Frequency (MHz) Max Output power (dBm) Max Output power (mW) Calculation Value (Note 1) Limit Value GFSK 2.4G 2446 -0.508 0.890 0.278 3.0 Note 1: Calculation Value =[(max. power of channel, mW)/(min. test separation distance, mm)] ·[√f(GHz)]. Fox example: 0.89/5*√2.446=0.278 ≤ 3.0 According to KDB447498 D01 V06, threshold at which no SAR required is ≤3.0 for 1-g SAR, separation distance is 5mm, and no simultaneous SAR measurement is required. 5. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

东振电子有限公司 天线规格承认书 Antenna Specification for Approval 客户名称 Customer Name： 产品名称： Product Name：2.4G 天线 全长35白色 客户型号： Product Name: 产品料号： Part NO.:19芯*0.12*1.4PVC 制 表： Write By：周 敏 日 期： Issued Date:2019-3-8 客 户: 工程R&D Dept采购Business Dept 承认 Approved By 东 振 电 子 研发R&D Dept 工程 Engineer Dept 审核 Approval u 标注 蝇{t 豆�起fi i宇 ,J，唱 A A B 3 C 3川脱）1 35MM � D －－－－－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－一－斗 J 「 「 F :; 、J 东振电子技术有限公司 主求： 尸AR I 1111← MA I仁同IAL UNIT I可 SCAL[ ＠吐1斗：� H 1 、标：4公主的为重要月才3天标注公主的按士o 1 s. 零 1 1 :名称： 2.4斗天线 材料1S;t;×0 17× 1 斗二V「 单位 mm ；二币、 P／＼可 N CJ 二1!W NG DAT[ CH二C-<l"G SUPP _ILi, C M 零 件编号 1 ( JtxO '2×11, 'V二 祖国： 又全 日， l 201S／〕；n门 审吱 快店商草草， A " Product Specification A. Electrical Characteristics Frequency 2400MHz ~2500MHz VSWR <1.0 Efficiency >20% Impedance 50 Ohm Polarization Line Gain 0.17DBi B. Material & Mechanical Characteristics Material of Radiator Cu Cable Type 1.4 白色 Connector Type : NO Dimension C. Environmental Operation Temperature - 30 °C ~ + 80 °C Storage Temperature - 30 °C ~ + 85 °C Test Equipment & Conditions 1． Network Analyzers : Agilent 8753D 5071B 2． Communications Test Set: Agilent E5515C 3． 3D Chamber Test System Effiency &Gain 2.40 ‐0.01 2.440 0.12 2.48 0.17 Radiation Pattern:

Page 1 of 42 FCC Test Report Report No.: AGC13923230701FE02 FCC ID : 2A65SDRONES2S3 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : MINI LED DRONE BRAND NAME : SYSTECH MODEL NAME : S3, S1, S2, S5, S6, S7, S8, S9, S161, S162, S163, S165, S166, S167, S168, S169, TK102, TK103, TK105, TK106, TK107, TK108, TK109, DM001, DM002, DM003, DM005, DM007, DM008, DM009, DM101, DM102, DM103, DM105, DM106, DM107, DM108, DM109, F1, F2, F3, F5, F6, F7, F8, F9, NH320, NH330, NH525, NH530, NH760, C127 APPLICANT : SHANTOU CHENGHAI SYSTECH TOYS CO., LTD DATE OF ISSUE : Aug. 02, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC13923230701FE02 Page 2 of 42 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Aug. 02, 2023 Valid Initial Release Report No.: AGC13923230701FE02 Page 3 of 42 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 7 2.4. TEST METHODOLOGY ............................................................................................................................. 7 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 7 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 7 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 8 4. DESCRIPTION OF TEST MODES ................................................................................................................... 9 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 10 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 10 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 10 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 10 6. TEST FACILITY .............................................................................................................................................. 11 7. PEAK OUTPUT POWER ................................................................................................................................ 12 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 13 8. BANDWIDTH .................................................................................................................................................. 15 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 15 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 15 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 15 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 19 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 19 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 19 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 19 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 26 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 26 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 26 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 26 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 26 11. RADIATED EMISSION ................................................................................................................................. 28 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 28 11.2. TEST SETUP .....…

Text truncated - open the document above for the full version.

Report No.: AGC13923230701AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC13923230701AP01 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************