2A6D4XM5000XM-5000

INSTRUCTION MANUAL XM-5000 VRA RF PACKAGE CONTENTS 2-Rectangular Plexiglass Boxes 1–Wireless Remote Control (REM-5000) 2– DC 9 Volt Power Adapter (ADA-13) 1-Power Spli(er Y-Cord (CAB-66) 2-14’ Exten Power Cables (CAB-010) 1-RF RECEIVER MODULE 2-3.5mm M-M Cable 12 Foot (CAB 012) REMOTE CONTROL (REM-5000 RF) 14’ POWER EXTENSION CABLES(CAB-010) POWER Y-CORD (CAB-66) 3.5mm Cables 6’/12’ (CAB-012) STEP ONE: Posi8on each Reinforcer box over or near the le< and right sound field speakers. Moun8ng these boxes to the wall of the sound room can be done by one of these four op8ons: 1) Using op8onal Dual Arm moun8ng brackets (DUA-001) 2) Using self tapping screws through predrilled holes on back of box 3) Using Velcro or double back tape to mount to top of loudspeakers. 4) Use op8onal corner moun8ng brackets (INS-KIT2) for moun8ng boxes in the corners of the sound booths. STEP TWO: Insert cables for power into bo(om of each VRA box con- nector block. (See LEGEND) Insert 3.5mm cables from RF RECEIVER MOD- ULE into IR SENSOR (blue) jack underneath each reinforcer box. STEP THREE: Mount centering box in between units onto wall using self tapping screws through the eyelet holes in back of box or double back tape to hold into posi8on. PUSH Use moun8ng holes on back of box to screw to wall or use moun8ng brackets LEGEND Volume DOWN Bu(on* Volume UP Bu(on* POWER-Coax Silver (2.1) IR SENSOR-BLUE CENTER BOX –RED (RCA) WIRED OUTPUT-BLACK WIRED INPUT-BLACK 3.5mm Plug POWER COAX 2.1mm *Volume can only be adjusted when unit is not acvated. DC 9 VOLT ADAPTER RF RECEIVER MODULE RF RECEIVER LED BLINKS WHEN CONNECTED & ACTIVATED REV 8 FCC SERIES II REMOTE CONTROL OPERATION LIGHTS- Ac8vates bright back lights to illuminate figure PATTERN- Selects LED light pa(erns (Blinks program number) CENTER- Ac8vates Center Box ACTION- Ac8vates 4 different Ac8ons/movements RIGHT- Ac8vates Right Box LEFT- Ac8vates Le< box CYCLE TIME- Ac8vates system for 4 seconds ON 8me SOUNDS- Ac8vates 10 different sound effects OPTIONAL ACCESSORIES CORNER MOUNTING BRACKET/INSTALLATION KIT (INS-KIT2) NOTE: Pa(ern Light blinks when signal is be- ing sent from remote when depressing RIGHT/LEFT/CENTER bu(ons 1) Marquee Dot 2) Marquee Bar 3) Marquee-Segment 4) All On Flashing 5) Blinking Random 1) Back & Forth 2) Stu(er Swing 3) Shi<-Shi<-Back 4) No Mo8on 1) Monkey 2) Cartoon Laugh 3) Boing 4) Tuba 5) Goofy Laugh 6) Duck 7) Hyena 8) Chimpmonk 9) Rooster 10) Kid Laughing 11) Mute DUCK CENTER BOX LPC-200 MOVING DOG CENTER BOX (LPA-600) MOTION SOUNDS LIGHT PATTERNS INTERCHANGEABLE TOY KIT (TOY-022) 6 Toys MAGNETIC BASE NEW ELITE VRA+SPEAKER XM-5000 VRA SLIDES IN- TO SPEAKER CHANNEL CAN BE MOUNTED ON TOP OR BOTTOM SPACE SAVING SLEEK WOODEN DESIGN FOAM GRILL CAN BE CLEANED TROUBLESHOOTING SYMPTOM CHECK Nothing/Dead Check power cord for 8ght connec8on. Make sure outlet has power available. Will not ac8vate Check IR sensor plugged in . Check iden8ty pin in proper loca8on. (See page 4) Right ac8vate with Le< bu(on Change box iden8ty pin on inside display board (See page 4) Works inside booth not test room Check cable to remote IR Sensors and placement for best pickup Intermi(ent opera8on Reposi8on IR sensor for more direct line-of-site pick up Stays on long a<er bu(on press Check that Cycle Time bu(on is not ac8vate (LED is ON) Humming or buzzing sound Gently reposi8on toy un8l noise stops Erra8c Opera8on Check for other sources of infra-red signals (LCD monitor, incandescent bulbs, etc) CONNECTOR BLOCK LEGEND Volume DOWN Bu(on* Volume UP Bu(on* POWER-Coax Silver IR SENSOR-BLUE CENTER BOX –RED WIRED OUTPUT-BLACK WIRED INPUT-BLACK FOR WIRED CONNECTIONS CONTACT PEHRATEK PRODUCTS 9285 Pierson Lake Drive Chaska, MN 55318 866-470-3532 *Volume can only be adjusted when unit is not acvated. *(Can use Y-CORD (CAB-66) from one Power Pack to operate both units) Use Power Extension Cables to lock into jack NOTE* POWER ON RED LED IS INSIDE BOX ON BACK PC BOARD TROUBLESHOOTING HOW TO CHANGE RF CHANNELS RF REMOTE CONTROL XM-5000 RF VDS-3000 RF PLACE JUMPER ON THE PINS MARKED AS BELOW ON BOTH TRANSMITTER AND RECEIVER TO OPER- ATE ON SECONDARY CHAN- NELS (UP TO 4) FOUR CHANNELS NO JUMER=CH 1 ADDR 01= CH 2 ADDR 02=CH 3 JUMPERS ON BOTH=CH 4 MAKE ALL CHANGES WITH BATTERIES REMOVED NOTE: Always power cycle the remote and VRA boxes a>er changing channels. RF RECEIVER MODULE XM-5000 RF VDS-3000 RF CH-3 CH-2 DO NOT REMOVE JUMPER ON RF PINS LOUDSPEAKER DISPLAY CABLE SPEAKER JACK POWER ON LED L/R ASSIGNMENT PINS P1=N/A P2+UPPER P3=RIGHT (NO PIN=LEFT) *Volume can only be adjusted when unit is not acvated. Bu'ons are located on bo'om of unit Per FCC 15.19(a)(3) and (a)(4) This device complies with part 15 of the FCC Rules. Opera8on is subject to the following two condi8ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera8on. FCC 15.21, The user manual or instruc8on manual for an inten8onal or uninten8onal radiator shall cau8on the user that changes or modifica8ons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer Block Diagram Product: XM-5000 Schemac RADIO MODULE BLOCK DIAGRAM HM-TRPW-433 MHz Radio MCU operates with internal RC oscillator at 8 MHz

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: EXTERNAL PHOTOS Product: XM-5000 PHOTOS EXTERNAL PHOTOS OF THE XM-5000 REMOTE

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer Label Product: XM-5000 LABEL FOR XM5000 FCC MODEL: XM-5000 FCC ID:2A6D4XM5000 SERIAL NUMBER: 409F445 LOCATION 9285 Pierson Lake Drive, Chaska, MN 55318 USA Label is affixed to case using high bonding glue for a permanent fit

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer INTERNAL PHOTOS Product: XM-5000 PHOTOS INTERNAL PHOTOS OF THE XM-5000 RF MODULE

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer INTERNAL PHOTOS Product: XM-5000 PHOTOS INTERNAL PHOTOS OF THE XM-5000 REMOTE

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer ANTENNA TRANSMIT- TER Product: XM-5000 ANTENNA SPECIFICATIONS FOR XM-5000 TRANSMITTER 1/4 Wave Monopole wire antenna Gain: 1.9 DBI Length: 6inches (17 cm) Form Factor: Wrapped inside plas5c enclosure lower sec5on

1 Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com HM-TRP Series 100mW Transceiver Modules V1.0 1. General HM-TRP series is a low cost, high performance transparent FSK transceiver with operating at 433/470/868/915 MHz. It features small size, high output power, high sensitivity, long transmission distance and high communication data rate with auto set up for communication change and data receiving and transmission control. There is UART interface, it is easy to realize the wireless data transmission with only providing the UART data. It is flexible for the users to set the UART baud rate, frequency, output power, data rate, frequency deviation, receiving bandwidth etc parameters. It is your ideal choice for designing wireless data transmission products which can be widely used on wireless data transmission field. 2. Features z Low cost, high performance , high reliability z FSK modulation, 2-way half –duplex communication, strong anti-interfere z 433/470/868/915MHz ISM band，globally license free. z Maximal output power100mW(20dBm)，output power adjustable between 1-20dBm z Sensitivity -117dBm z Supply current for Tx 100mA@20dBm, 40mA@14dBm z Supply current for Rx 25mA z Low current sleep mode 1uA z Standard TTL UART interface, extendable to RS232 or other interface z Operation frequency can be configured, acceptable for several modules working in different frequency with no disturbance on each other. z Optional for frequency deviation and receiving ISM bandwidth, users can be modulated by software. z Easily use, auto exchange on communication & transceiver z Communication speed 1.2kbps -115.2kbps，can be modulated through software z Afford ENABLE control signal，user self control work duty cycle z RSSI function z With LED indication z Longer transmission distance，over 1Km in open air z Small size 16X20X2MM，9 PIN DIP & 9 PIN SMD package，easy for assembly . z Tuning free z Accord FCC,ETSI standard 3. Application „ Remote control, remote measurement system; „ Wireless meter „ Access control „ Identification system HM-TRP HM-TRP Series „ Data collection „ IT household appliance „ Intelligence household appliance „ Baby monitoring system 4. Pin Description Figure 1. HM-TRP (DIP) Pin Description Figure 2. HM-TRP (SMD) Pin Description Name Note VCC Power supply,2.4-3.6V DC power, recommendation 3.3V DC power DTX Data transmission GND Ground DRX Data receiving CONFIG Set low for configuration mode, while set high for communication ENABLE Set low for normal mode for data transceiver , while back to sleep if set high TEST Dis-connected 2 Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com HM-TRP Series ANT Input/output interface with 50 ohm antenna 5. Maximum specifiction Parameter Min Max Unit Power supply(VCC) -0.3 +3.6 V Storage temperature -40 +150 °C Operate temperature -40 +85 °C Reflow temperature +260 °C 6. Parameter Parameter Condition Min Typical Max Unit Power supply ( VCC) 2.4 3.3 3.6 V Operate temperature -40 25 85 °C Operate frequency HM-TRP-433 414 434 454 MHz HM-TRP-470 450 470 490 HM-TRP-868 849 869 889 HM-TRP-915 895 915 935 Max output power 18 20 dBm Output range 1 20 dBm Receive Sensitivity FSK,Fdev=35K, DR=1.2Kbps, -117 -115 dBm FSK,Fdev=35K, DR=9.6Kbps, -114 -112 FSK,Fdev=35K, DR=40Kbps -111 -109 FSK,Fdev=35K, DR=100Kbps -104 -102 Tx Current 20dBm output power 100 120 mA 14dBm output power 40 50 Rx Current 25 30 mA Sleep Current 1 2 uA Modulate data rate 1.2 115.2 Kbps Modulate deviation 10 160 KHz Receive bandwidth 30 620 KHz UART Data Rate 1.2 115.2 Kbps UART data bit 8 bit UART stop bit 1 bit 3 Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com HM-TRP Series 7. LED function The HM-TRP add the LED function for easier debug & function demo, thus the users can easily understand whether the module is working or not or in any other status. LED function: 1. The red and green LED will flash when there is power on if the module start working. 2. The module will be ready for Config status if ENABLE pin is low，CONFIG pin is low. It will be in Config if the red and green LED keep lighting. The green and red LED will not keep lighting if the module is not in Config mode. 3. The red LED flash when the module is in transmission ，the red LED will be off if the transmission finished. 4. The green LED is off when the module is in receiving status, the green led will flash once if the module receive data. 8. Config Instruction You need to Config the parameter and inquiry for different need to realize the function. The HM-TRP can Config and inquiry for working frequency, wireless data rate , receiving ISM bandwidth, frequency deviation, transmission power, UART transfer baud rate & RSSI signal reading etc. Config and Inquiry methods: The module will be ready for Config status if ENABLE pin is low，CONFIG pin is low. It will be in Config if the red and green LED keep lighting. Then you can Config & inquiry on the module. The Config instruction format is as AA FA+[instruction]+[parameter].The instruction is 1 byte，the parameter is the HEX data of 0-4 byte which the high byte before the low byte. The instruction’s transfer speed should keeps the same as the transfer speed of UART. The instruction’s transfer speed will change accordingly if changes the transfer speed of UART .The range of transfer speed of the instruction is from 1.2Kbps –115.2K bps. Config& Inquiry instruction description: 1. Instruction[F0]: Reset to default parameter, no parameter follows Config instruction：AA FA F0 2. Instruction[E1]: Reading the current Config parameter, no parameter follows Config instruction：AA FA E1 3. Instruction [D2]: Set up working frequency，[parameter]4 byte，[parameter] Unit :Hz Set up range: HM-TRP-433: 414000000-454000000Hz HM-TRP-470: 450000000-490000000Hz HM-TRP-868: 849000000-889000000Hz 4 Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com …

Text truncated - open the document above for the full version.

This report must not be used to claim product certification, approval, or endorsement by A2LA or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. Pehratek Products XM-5000 RF and Remote Control FCC 1.1307:2022 Periodic Report: PEHR0004.8, Issue Date: May 18, 2022 CERTIFICATE OF EVALUATION 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing Last Date of Evaluation: May 17, 2022 Pehratek Products EUT: XM-5000 RF and Remote Control RF Exposure Evaluation Standards Specification Method FCC 1.1307:2022 FCC 1.1307:2022 Results Method Clause Description Applied Results Comments (b)(3)(i)(A) Exemption From RF Exposure Evaluation Yes Pass None Deviations From Evaluation Standards None Approved By: Donald Facteau, Process Architect Report No. PEHR0004.82/11 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PEHR0004.83/11 ACCREDITATIONS AND AUTHORIZATIONS 2021.09.01 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Each laboratory is accredited by A2LA to ISO / IEC 17025, and as a product certifier to ISO / IEC 17065 which allows Element to certify transmitters to FCC and IC specifications. Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: California Minnesota Oregon Texas Washington Report No. PEHR0004.84/11 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 A2LA Lab Code: 3310.04 Lab Code: 3310.05 Lab Code: 3310.02 Lab Code: 3310.03 Lab Code: 3310.06 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PEHR0004.85/11 PRODUCT DESCRIPTION 2018-07-17 Client and Equipment Under Evaluation Information Company Name: Pehratek Products Address: 9285 Pierson Lake Road City, State, Zip: Chaska, MN 55318 Evaluation Requested By: Jim Pehringer EUT: XM-5000 RF and Remote Control Date of Evaluation: May 17, 2022 Information Provided by the Party Requesting the Evaluation Functional Description of the Equipment: The XM-5000 remote control utilizes a modular transceiver from Hoperf Electronics Model HM-TRP to wirelessly control functions of a visual reinforcement audiometer typically used in close proximity. Short bursts of data (FSK modulation) are sent on a 434 MHz frequency carrier to operate and set functions of these devices typically used in a sound room for distraction purposes. Objective: To demonstrate compliance with FCC Requirements for RF exposure for 1.1307 RF exempt devices Report No. PEHR0004.86/11 RF Exposure Condition 2018-07-17 The following RF Exposure conditions were used for the assessment documented in this report: Intended Use Mobile Location on Body (if applicable) Head/Torso How is the Device Used The equipment is used at a distance greater than 20 cm from the user. Radios Contained in the Same Host Device Periodic Simultaneous Transmitting Radios None Body Worn Accessories N/A Environment General Population/Uncontrolled Exposure Report No. PEHR0004.87/11 EXEMPTION FROM RF EXPOSURE EVALUATION EXRPT.2022.02.09.0 OVERVIEW With respect to the limits on human exposure to RF emissions provided in 47 CFR §1.1…

Text truncated - open the document above for the full version.

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: James L. Pehringer Product: XM-5000 Schemac RADIO MODULE SCHEMATIC HM-TRPW-433 MHz Radio

PEHRATEK PRODUCTS REV 1 DATE: April 15,2022 Draed By: SCHEMATIC REMOTE CONTOL Product: XM-5000 SCHEMATIC FOR XM-5000 REMOTE CONTROL

This report must not be used to claim product certification, approval, or endorsement by A2LA or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. Pehratek Products Remote Control for XM-5000 RF FCC 15.231:2022 Low Power Radio Report: PEHR0004.6, Issue Date: June 20, 2022 CERTIFICATE OF TEST 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing. Last Date of Test: June 6, 2022 Pehratek Products EUT: Remote Control for XM-5000 RF Radio Equipment Testing Standards Specification Method FCC 15.231:2022 ANSI C63.10:2013 Results Method Clause Test Description Applied Results Comments 6.2 Powerline Conducted Emissions (Transmitter) No N/A Not required for a battery powered EUT. 6.5, 6.6 Field Strength of Fundamental Yes Pass 6.5, 6.6 Spurious Radiated Emissions Yes Pass 6.9.2 Emissions Bandwidth Yes Pass 7.5 Duty Cycle Yes Pass Deviations From Test Standards None Approved By: Eric Brandon, Department Manager Report No. PEHR0004.62/31 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PEHR0004.63/31 ACCREDITATIONS AND AUTHORIZATIONS 2021.09.01 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Each laboratory is accredited by A2LA to ISO / IEC 17025, and as a product certifier to ISO / IEC 17065 which allows Element to certify transmitters to FCC and IC specifications. Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: California Minnesota Oregon Texas Washington Report No. PEHR0004.64/31 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 A2LA Lab Code: 3310.04 Lab Code: 3310.05 Lab Code: 3310.02 Lab Code: 3310.03 Lab Code: 3310.06 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PEHR0004.65/31 MEASUREMENT UNCERTAINTY TMU.2015.07.10 Measurement Uncertainty When a measurement is made, the result will be different from the true or theoretically correct value. The difference is the result of tolerances in the measurement system that cannot be completely eliminated. To the extent that technology allows us, it has been our aim to minimize this error. Measurement uncertainty is a statistical expression of measurement error qualified by a probability distribution. A measurement uncertainty estimation has been performed for each test per our internal quality document QM205.4.6. The estimation is used to compare the measured result with its "true" or theoretically correct value. The expanded measurement uncertainty (K=2) can be found in the table below. A lab specific value may also be found in the applicable test description section. Our measurement data meets or exceeds the measurement uncertainty requirements of the applicable specification; therefore, the test data can be compared directly to the specification limit to determine compliance. The calculations for estimating measurement uncertainty are based upon ETSI TR 100 028 (or CISPR 16-4-2 as applicable), and are available upon request. The following table represents the Measurement Uncertainty (MU) budgets for each of the tests that may be contained in this report…

Text truncated - open the document above for the full version.

FIELD STRENGTH OF FUNDAMENTAL photo PSA-ESCI 2022.1.12.0 photos PSA-ESCI 2022.1.12.0 SE 005.jpg SE 012.jpg 12 FIELD STRENGTH OF FUNDAMENTAL photo PSA-ESCI 2022.1.12.0 photos PSA-ESCI 2022.1.12.0 SE 013.jpg SE 014.jpg 14 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2022.1.12.0 photos PSA-ESCI 2022.1.12.0 SE 005.jpg SE 011.jpg 11 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2022.1.12.0 photos PSA-ESCI 2022.1.12.0 SE 012.jpg SE 013.jpg 13 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2022.1.12.0 photos PSA-ESCI 2022.1.12.0 SE 014.jpg XMit 2022.02.07.0 SE 005.jpg OCCUPIED BANDWIDTH XMit 2022.02.07.0 SE 005.jpg DUTY CYCLE XMit 2022.02.07.0 IMG_0543.JPG IMG_0544.JPG DUTY CYCLE