2A6HH-Y25Retractable Cable ALL-in-one car charger

Retractable Cable ALL-in-one car charger User Manual Important Safety Instructions SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the car charger. Before use, read all Instructions and cautionary markings on the car charger. 1 Do not expose the charger to rain. moisture, or snow. 2 Use of an attachment not recommended or sold by the car charger manufacturer may result in o risk of fire, electric shock or injury to persons. 3. To reduce the risk of damage to the cigarette lighter connector and cord. pull by the cigarette lighter connector rather than the cord when disconnecting the charger. 4. Make sure the cord is located so that it will not be stepped on. tripped over. or otherwise subjected to damage or stress. 5 Do not operate the charger with o damaged cord or cigarette lighter connector - replace it immediately. 6.Do not operate the charger if it has received o sharp blow, been dropped. or otherwise damaged in any way, take it to a qualified serviceperson. 7. Do not disassemble the charger, take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 8. To reduce the risk of electric shock, unplug the charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk 9. This device has been tested to operate safely in o laboratory environment with ambient temperatures ranging from 0-25 and can be used normally at vehicle interior temperatures. Specifications Input Output Input12V 5.4A Total 65W Max Type-C Cable30W Max Lighting Cable12W Max Magnetic Watch Charger2.5W Max USB-A Port12W Max Type-C Port12W Max This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the opplicahousehold waste. Instead, it shall be handed over to the opplicable collection point for the recycling of electrical ond electronic equipment 68CM WATCH USB-A USB-C USB-C IOS Magnetic Charger Extension and Retraction Instructions:Pull the cable out to extend it, Briefly pull again to retract it automatically. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. WARNING

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:HOPEKCORPORATIONINC Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates FRN:0034562900 ContactName:YangyangXu TelephoneNo:(561)875-9826 E-mail:[email protected] ThisletteristoconfirmthattheUSAgentforServiceofProcessacceptsresponsibilitytoactas alocalrepresentativeonbehalfofShenzhenYinaiIntelligentManufacturingTechnologyCo.,Ltd TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. Applicant: CompanyName:ShenzhenYinaiIntelligentManufacturingTechnologyCo.,Ltd ProductDescription:RetractableCableALL-in-onecarcharger FRN:0032245003 GranteeCode:2A6HH FCCID:2A6HH-Y25 ContactName:JimmySun Address:6Floor,DBuilding,HuamingchengHigh-TechPark,MatianStreet,GuangmingDist, Shenzhen,Guangdong,China TelephoneNo:+8613926535499 E-mail:[email protected] TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. ThisAgreementisvaliduntil(Permanentlyvalid). Date:2026/9/17 Applicant’sName: ShenzhenYinaiIntelligentManufacturing TechnologyCo.,Ltd USAgentforServiceofProcess’sName: HOPEKCORPORATIONINC Title:GeneralManagerTitle:Manager SignatureSignature

Rev 1/26/2023 Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Sept. 08, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A6HH-Y25 [Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24- 886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Jimmy Sun Rev 1/26/2023 Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Sept. 08, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A6HH-Y25 [Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Jimmy Sun

Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 17, 2026 Subject; Request for Confidentiality FCC ID: 2A6HH-Y25 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Jimmy Sun Title: General Manager

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Date: Sept. 08, 2026 Product Model Number: Y25 FCC ID: 2A6HH-Y25 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: General Manager Email: [email protected] Telephone: +86 13926535499 On behalf of: Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd

Ext Photos Model: Y25 Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

18.45MM 20.9MM

Int Photos Model: Y25 Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 ANT Photo 11 Photo 12 Photo 13 Photo 14 Photo 15 Photo 16 Photo 17

- Page 1 of 10 - Report No.: HB20260828006E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Retractable Cable ALL-in-one car charger Trade Mark: N/A Model Number: Y25 FCC ID: 2A6HH-Y25 Prepared for Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 10 - Report No.: HB20260828006E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 6 2.1 TEST LABORATORY ..................................................................................................................................................... 6 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 6 2.4 TEST SOFTWARE ........................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 7 4 RF EXPOSURE..................................................................................................................................................... 8 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 8 4.1.1. Limit ............................................................................................................................................................ 8 4.1.2. Test Procedures ........................................................................................................................................... 8 4.1.3. Test Setup .................................................................................................................................................... 8 4.1.4. Test Result ................................................................................................................................................... 8 5 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................10 - Page 3 of 10 - Report No.: HB20260828006E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Address ................................. : 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Manufacturer's Name .......... : Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Address ................................. : 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Product description Product name ........................ : Retractable Cable ALL-in-one car charger Model Number ....................... : Y25 Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Aug. 28, 2026~Sept. 05, 2026 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : (M i n g L i u) Authorized Signatory : (L e o S u) - Page 4 of 10 - Report No.: HB20260828006E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (8…

Text truncated - open the document above for the full version.

一、Floor Plan: Unit： MM 1 2 C A B - - D → 磁 铁 E A 7 . 65 ± 0 . 0 5 3 . 0 ± 0 . 0 5 B 2 ± 1 C 1 5 ± 0 . 2 D E 2 0 . 5 ± 0 . 5 21 ± 0 . 1 F G 7 . 7 ± 0 . 0 5 1 3 . 5 ± 0 . 1 H 2 3 . 5 ± 0 . 2 I J 25 ± 0 . 2 2 . 55 ± 0 . 1 K 2.25±0.1 L 8 ± 1 M 二、Product Parameter： Wire diameter Turns Note 1 - 2 0 . 08 * 2 4 P 1 2 三、technical requirements ： 1.Secure the ends of the wires to prevent them from loosening or breaking. 2. Cut the excessively long wire according to the customer's requirements, tin it, and ensure that the tin coating depth is uniformly 2±1MM. 3. Apply an appropriate amount of white glue on the soft magnetic sheet, attach the coil, and keep the product surface clean and tidy during the process. 4. The soft magnetic sheet used has round holes and is undamaged. 5. Additional processing (as per customer's requirements): Install a 7.65x3.0mm magnet in the middle round hole of the finished product and attach a φ20*0.5MM hole-covered cotton (with a hole of φ10MM) on the back of the finished coil, then back a φ20*0.12MM white background with black characters. Foot Hot air twisted yarn 五、bill of materials： NoNamematerials Supplier Note 1 Hot air twisted yarn 0.08X24P Uighur-Han or equivalent 2 magnetic sheet G25 Uighur-Han or equivalent 3 Tin High-temperature environmental protection Uighur-Han or equivalent 4 white glues BY882 Uighur-Han or equivalent 5 strong magnet 7.65*3 Uighur-Han or equivalent 6 Double-sided adhesive tape Uighur-Han or equivalent 四、electrical parameter 1.Inductance value, Q value: PIN 1 — 2 = 7.6uH ± Qvalue ≥35 0.2UH Φ20*0.12MM white background with black characters, self-adhesive backing Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China

- Page 1 of 33 - Report No.: HB20260828006E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Retractable Cable ALL-in-one car charger Trade Mark: N/A Model Number: Y25 FCC ID: 2A6HH-Y25 Prepared for Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 33 - Report No.: HB20260828006E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 6 1.4 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 6 1.5 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................... 7 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 9 4 LIST OF TEST EQUIPMENT .................................................................................................................................10 5 TEST ITEM AND RESULTS ...................................................................................................................................12 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 12 5.2 CONDUCTED EMISSION ............................................................................................................................................. 13 5.3 RADIATED EMISSION ................................................................................................................................................ 15 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 20 6 PHOTOGRAPHS OF THE TEST SETUP ..................................................................................................................21 7 PHOTOGRAPHS OF THE EUT..............................................................................................................................22 - Page 3 of 33 - Report No.: HB20260828006E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Address ................................. : 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Manufacturer's Name .......... : Shenzhen Yinai Intelligent Manufacturing Technology Co., Ltd Address ................................. : 6 Floor, D Building, Huamingcheng High-Tech Park, Matian Street, Guangming Dist, Shenzhen, Guangdong, China Product description Product name ........................ : Retractable Cable ALL-in-one car charger Model Number ....................... : Y25 Standards ............................. : FCC Part 15C Test procedure ....................... : IEEE/ANSI C63.10-2020 + Cor. 1-2023 + C63.10a-2024 + Errata to C63.10a-2024 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Aug. 28, 2026~Sept. 05, 2026 Test Result .............................................. : Pass Testing…

Text truncated - open the document above for the full version.

- Page 1 of 2 - Photographs of the Test Setup Model: Y25 Radiated Emission Below 30MHz Radiated Emission Above 30MHz - Page 2 of 2 - MPE