2A6MS-B51SPROBluetooth Headset

Shenzhen Zhichuang All Technology Co., Ltd

Click to zoom

Application Details

Equipment Class: DTS - Digital Transmission System
Date of Grant: Aug 03, 2023
Application Purpose: Original Equipment
Date of Application: Aug 03, 2023
Equipment Note: Bluetooth Headset
Frequency Range: 2402.00000000 - 2480.00000000
Company: Shenzhen Zhichuang All Technology Co., Ltd
Country: China

Documents & Files

Select a file to view

Document Text

Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.

Users Manual

Operating guide 使用指南 B51S Pro/B51S Pro Max 1.音量加/下一首：短按音量加，长按下一首 2.开关键/多功能按键：开关机和播放暂停，多功能切换 3.音量减/上一首：短按音量减，长按上一首 4.LED显示灯 5.MIC 6.喇叭：气传导发声单元按键功能部件概述感谢您选用本公司生产的蓝牙耳机，为了更好的体验本产品，使用前请仔细阅读使用说明书，如有印刷错误或翻译失误望广大用户谅解耳机通过磁吸充电线进行充电，充电完成后，工作指示灯从红色（常亮）变为蓝色（常亮）。注意："请使用符合国家标准且通过 CCC认证的直流5V电源适配器进行充电 "。充电使用关机状态下，长按多功能键2秒，蓝灯常亮1秒，红/蓝灯交替闪烁，耳机开机并且直接进入配对搜索模式，开机伴有提示音，打开手机或智能电子设备，从蓝牙列表中，找到 “Sanag B51S Pro/B51S Pro Max ,”，并点击连接。蓝牙配对 ●首次开机配对：搜索耳机连接成功 Settings MY DEVICES Sanag B51S Pro Sanag B51S Pro MaxSanag B51S Pro Max Settings MY DEVICES Sanag B51S Pro Connected 当耳机低电压时，红灯1秒闪1次,并且有报警音,此时请接上电源适配器对耳机进行充电，否则当耳机电量过低时耳机会自动关机。按键操作当手机和耳机超出蓝牙连接距离后，耳机出现伴有提示音，手机和耳机断开连接。3分钟之内回到耳机和手机蓝牙连接范围之内耳机和手机可以自动回连，超出三分钟后耳机进入待机状态，如果5 分钟后未连接，耳机会自动关机。 ●断连，超距离断开或设备关机：关机状态下，长按多功能按键2秒，蓝灯常亮1秒，红/蓝灯交替闪，耳机开机并伴有提示音。 ●耳机开机：耳机开机状态下，长按多功能键4秒，红灯常亮后熄灭，耳机关机。伴有提示音。 ●耳机关机：耳机开机状态下，双击开关键，蓝灯10秒闪1次，切换TF卡模式或蓝牙模式，伴有“Music”提示音。 ●TF卡模式或蓝牙模式：耳机通话状态下，短按音量加键音量持续加，加到最大，伴有提示音。 ●音量加：耳机通话状态下，短按音量减键音量持续减（最小音），伴有“嘟嘟” 提示音。 ●音量减：来电话时，短按多功能键，接听；长按多功能键，拒接。 ●接听/拒接：短按多功能键，挂断。 ●通话中挂断音乐状态下，短按音量加键音量持续加，加到最大时有嘟嘟提示音。播放状态，长按切换下一曲。 ●下一曲按键/音量加音乐状态下，短按音量减键音量持续减，减到最小时有嘟嘟提示音。播放状态，长按切换上一曲。 ●上一曲按键/音量减任何状态下，数据线插入PC或者手机（要有OTG转接头）读取到U盘，并将所需要的歌曲或者数据文件拷贝至设备内。报警：红灯1秒闪1次，伴有报警音“please charge”。关机：红灯亮3秒，耳机关机。 ●如何拷贝数据短按多功能键，音乐播放/暂停，播放状态：蓝灯5秒钟闪1次暂停状态：蓝灯10秒闪一次。 ●音乐播放/暂停: 音乐状态下，三击开关键，单曲循环提示“嘟”一声短音，全部循环提示“嘟嘟”两声。 ●单曲循环或全部循环 ●低电压报警/关机短按多功能键，音乐播放/暂停，播放状态：蓝灯5秒钟闪1次暂停状态：蓝灯10秒闪一次。 ● 开机没有连接任何手机, 5分钟后自动关机。 ● 首次使用请将本产品充满电。 ● 请勿以任何理由拆除或维修改装本产品，否则可能会导致起火，电子击穿甚至彻底损坏本产品。 ● 如充电完毕，请断开充电器与本设备的连接，需拔掉充电器，连续充电时间请勿超过12小时。 ● 请不要将旧电池扔在旧生活垃圾中进行处理，若电池处置不当可能会导致电池起火或爆炸，请遵守当地规定处理本产品，电池及其他附件。 ● 电池禁止拆卸，撞击，挤压或投入火中，若出现严重膨胀，请勿继续使用。电池不得暴露在过热的环境中。 ● 请勿自行维修本产品。 ● 消费者若使用电源适配器充电，则应购买配套使用获得CCC认证并满足标准电源适配器。注意事项： ●重量：裸机25g ●耳机类型：运动蓝牙耳机 ●蓝牙版本：V 5.3 ●充电输入：DC 5V --- 120mAh ●传输距离：10米 ●产品阻抗：16Ω±10% ●耳机尺寸(长，宽，高）：138*106*41mm ●充电时间：1.5小时左右（首次充电最好大于2小时） ●工作温度：-20°C到70°C ●存储温度：-20°C到70°C 基本参数 1. Volume increase / Next song: short press volume increase, long press one song 2. K ey on / multi-function keys: switch on / off, play pause, multi-function switching 3. V olume decrease / previous song: short press volume decrease, long press previous song 4. LED display lamp 5. MIC 6. Horn: air conduction sound generating unit Overview of key features Thank you for choosing our bone conduction Bluetooth headset for a better experience Please read the instruction manual carefully before using this product. If there is any printing error or Translation errors hope that the majority of users understand Settings MY DEVICES Sanag B51S Pro Sanag B51S Pro MaxSanag B51S Pro Max Settings MY DEVICES Sanag B51S Pro Connected Charging use In the off state, long press the multi-function button for 2 seconds, the blue light is always on for 1 second, the red/blue light alternately flashes, the headset is turned on and directly enters the pairing search mode, the power is accompanied by a prompt sound, and the mobile phone or smart electronic device is turned on, from Bluetooth In the list, find "Sanag B51S Pro / B51S Pro Max" and click Connect. Bluetooth pairing ●First boot pairing: Search headset Connection succeeded When the earphone is under low voltage, the red light flashes once a second and there is an alarm sound. At this time, please connect the power adapter The adapter charges the headset, otherwise the headset will automatically shut down when the power of the headset is too low. The earphone is charged through a magnetic charging wire. After the charging is completed, the working indicator changes from red (steady on) to blue (steady on). Note: "Please use a DC 5V power adapter that meets national standards and has passed CCC certification for charging." ●TF card mode or Bluetooth mode： Key operation When the mobile phone and headset exceed the Bluetooth connection distance, the headset appears with a prompt tone, and the mobile phone and headset are disconnected. Return to the Bluetooth connection range between the headset and the mobile phone within 3 minutes. The headset and the mobile phone can be automatically connected. After 3 minutes, the headset enters the standby mode. If it is not connected after 5 minutes, the headset will automatically shut down. When the headset is on, double-click the on key, and the blue light flashes once every 10 seconds to switch the TF card mode or Bluetooth mode, accompanied by "Music" prompt tone. ●Disconnection, over distance disconnection or equipment shutdown: In the off state, press and hold the multi-function button for 2 seconds, the blue light is always on for 1 second, the red/blue light flashes alternately, and the headset is turned on with a beep. ●Headset on: When the headset is turned on, press and hold the multi-function button for 4 seconds, the red light will be on and then it will go out, and the headset will turn off. Accompanied by a beep. ●Headset off: ●volume up When the headset is on a call, short press the volume up key to continuously increase the volume to the maximum, accompanied by a prompt tone. ●volume down When the headset is talking, press the volume reduction button and the volume continues to decrease (the minimum tone), accompanied by a beep tone. Short press the multi-function button to hang up. ●Hang up during a call The first call comes in, short press the multi-function button to answer it; long press the multi-function button to reject it. ●Answer / reject: Short press the multi-function button, music play/pause, play status: blue light flashes once in 5 seconds Pause status: blue light flashes once in 10 seconds. ●Music play / pause: Under the state of music, three strikes open key, single cycle prompt "du" a short note, all cycle Prompt "beep" two times. ●Single loop/full loop: In any state, insert the data cable into the PC or mobile phone (with OTG adapter) to read the USB flash disk, and copy the required songs or data files to the device. ●How to copy data ●Low voltage alarm/shutdown In the music state, short press the volume up…

Text truncated - open the document above for the full version.

Attestation Statements

Shenzhen Zhichuang All Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/3/2023 U.S. Agent Designation Sh enzhen Zhichuang All Technology Co., Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A6MS-B51SPRO): Name and company of U.S. agent: FCC US Agent, LLC Physical U.S. address of agent: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN of U.S. agent: 0033402884 Email address of U.S. agent: [email protected] FCC US Agent, LLC acknowledges their obligation to accept service of process on behalf of Shenzhen Zhichuang All Technology Co., Ltd. Shenzhen Zhichuang All Technology Co., Ltd with the FRN 0032310831 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Since rely, Signature qingmin chen Deputy General Manager Shenzhen Zhichuang All Technology Co., Ltd Signature Tim Payne Manager FCC US Agent, LLC 48_[model] US_Agent_2.911(d)(7)-U, V05

Attestation Statements

Covered Equipment Identification Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows: We, applicant Company Name: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road,Xialilang Community, Nanwan Str. Longgang District, Shenzhen, China Phone: +86-1802547868 certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2023-07-31 Name / Title: Qingmin Chen / Deputy General Manager Company: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7,Xiangye Road,Xialilang Community,Nanwan Str. Longgang District, Shenzhen, China Phone: +86-18025478685 Fax: N/A E-Mail: [email protected]

Attestation Statements

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2A6MS-B51SPRO B51S Pro, B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro We, applicant Company Name: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road,Xialilang Community, Nanwan Str. Longgang District, Shenzhen, China Phone: +86-1802547868 certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2023-07-31 Name / Title: Qingmin Chen / Deputy General Manager Company: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7,Xiangye Road,Xialilang Community,Nanwan Str. Longgang District, Shenzhen, China Phone: +86-18025478685 Fax: N/A E-Mail: [email protected]

Cover Letter(s)

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2A6MS-B51SPRO B51S Pro, B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro For the products listed above, we request permanent confidentiality for all applicable exhibits as there are: • the Operational Description • the Block Diagram • the Schematics The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Signature Date:2023-07-31 Name / Title: Qingmin Chen / Deputy General Manager Company: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7,Xiangye Road,Xialilang Community,Nanwan Str. Longgang District, Shenzhen, China Phone: +86-18025478685 Fax: N/A E-Mail: [email protected]

Cover Letter(s)

Shenzhen Zhichuang All Technology Co., Ltd D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road,Xialilang Community, Nanwan Str. Longgang District, Shenzhen, China Date: July 31, 2023 FCC ID: 2A6MS-B51SPRO Model Number: B51S Pro, B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro To: Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Shenzhen Zhichuang All Technology Co., Ltd hereby declare that our product (Bluetooth Sports Headphones) Model Number: B51S Pro, B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro board, Schematic, Hardware version, Software version, structure and internal photos are same, named differently due to marketing purposes. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, (Signed) Name/Title: Qingmin Chen / Deputy General Manager Company: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road,Xialilang Community, Nanwan Str. Longgang District, Shenzhen, China Tel: +86-18025478685 Fax: N/A E-Mail: [email protected]

Cover Letter(s)

Audit Mode Request Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern The company as listed hereby requests to supersede the exhibits listed in the table below from the application with the FCC ID as listed after the 30 days period. MODEL NUMBER: (MODEL NUMBER OF UNIT TESTED) B51S Pro, B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro FCC ID: 2A6MS-B51SPRO Granted on: 08/04/2023 Company Name: Shenzhen Zhichuang All Technology Co., Ltd Address: D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road, Xialilang Community, Nanwan Str. Longgang District, Shenzhen, China Phone: +86-18025478685 The Reason for the supersede are as follows: Exhibit type Reason for supersede Appendix A test data BT_rev Update Product Name keep same with Amazon as Amazon require. Appendix B test data BT LE_rev Update Product Name keep same with Amazon as Amazon require. External photos_rev Update trade mark keep same with Amazon as Amazon require. Label and label location_rev Update Product Name keep same with Amazon as Amazon require. Operation description_rev Update Product Name keep same with Amazon as Amazon require. RF exposure evaluation_rev Update Product Name keep same with Amazon as Amazon require. Test Report BT LE_rev Update Product Name keep same with Amazon as Amazon require. Test Report BT_rev Update Product Name keep same with Amazon as Amazon require. New exhibits will be uploaded to the application once the audit mode is active, Sincerely, 2023-08-07 Signature Date Printed Name Qingmin Chen Job Title Deputy General Manager Company Shenzhen Zhichuang All Technology Co., Ltd Address D401, Ganghong Complex Building, Building 2, No.7, Xiangye Road, Xialilang Community,Nanwan Str. Longgang District, Shenzhen, China Phone +86-18025478685 Email [email protected]

External Photos

ID Label/Location Info

Page 1 of 1 FCC ID: 2A6MS-B51SPRO _____________________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 LABEL AND LOCATION (Size: L 6.0cm x W 1.5cm) Label Location Bluetooth Headset Model: B51S Pro FCC ID: 2A6MS-B51SPRO

Internal Photos

RF Exposure Info

Page 1 of 4 FCC ID: 2A6MS-B51SPRO Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information FCC ID : 2A6MS-B51SPRO Product name : Bluetooth Headset Test Model : B51S Pro Additional Model No. : B51S Pro Max, B51 Pro, B51 AI Max, B51S, B30S Pro Max, B30 Pro, B30 AI Max, B30S, B30S Pro Model Declaration : PCB board, structure and internal of these model(s) are the same, So no additional models were tested Power Supply : Input: DC 5V, 120mA DC 3.7V by Rechargeable Li-ion Battery, 150mAh Hardware Version : V0.1 Software Version : V0.5.230517.1620 Frequency Range : 2402MHz ~ 2480MHz Channel Number : 79 channels for Bluetooth V5.3 (DSS) 40 channels for Bluetooth V5.3 (DTS) Channel Spacing : 1MHz for Bluetooth V5.3 (DSS) 2MHz for Bluetooth V5.3 (DTS) Modulation Type : GFSK, π/4-DQPSK, 8-DPSK for Bluetooth V5.3 (DSS) GFSK for Bluetooth V5.3 (DTS) Bluetooth Version : V5.3 Antenna Type : Ceramics Antenna Antenna Gain : 1.75dBi Exposure category : General population/uncontrolled environment EUT Type : Production Unit Device Type : Portable Device Page 2 of 4 FCC ID: 2A6MS-B51SPRO Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 2. Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices Page 3 of 4 FCC ID: 2A6MS-B51SPRO Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 4. Condu…

Text truncated - open the document above for the full version.

Test Report

承認書 SPECIFICATION FOR APPROVAL 客戶名稱 CUSTOMER ：客戶料號 CUSTOMER’S P/N ：料號 PART NUMBER ： WAN3216F245H08 規格 DESCRIPTION ： Chip Antenna 3216 L Ant 2.45G Type H08 版本 VERSION ： V1.6 日期 ISSUE DATE ： 2022/01/05 客戶承認 CUSTOMER APPROVED 工程部 R&D CENTER 承認 APPROVAL 確認 CHECKED 製作 DRAWN Ray Tennyson Snow 萬誠科技股份有限公司 OneWave Electronic Co., Ltd. 11261台北市北投區立功街151號1樓 1F, No. 151, Li Gong Street, Beitou District, Taipei City 11261, Taiwan 電話: (02) 2898-2220 TEL: +886 2 2898-2220 傳真: (02) 2898-5055 FAX: +886 2 2898-5055 2/11 ONEWAVE TECHNOLOGY CO., LTD. 3216 Chip antenna For Bluetooth / WLAN Applications Dimension (mm) L 3.23 ± 0.20 W 1.66 ± 0.20 T 0.45 ± 0.20 P/N: WAN3216F245H08 3/11 ONEWAVE TECHNOLOGY CO., LTD. Part Number Information WAN 3216 F 245 H 08 A B C D E F A Product Series Antenna B Dimension L x W 3.2 x 1.6mm (±0.2mm) C Material High K material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode PIFA & Single Feeding F Antenna type Type = 08 1. Electrical Specification Remark : Bandwidth & Peak Gain was measured under evaluation board of next page Specification Part Number WAN3216F245H08 Central Frequency 2450 MHz Bandwidth 120 (Min.) MHz Return Loss -6.5 (Max) dB Peak Gain 1.75 dBi Impedance 50 Ohm Operating Temperature -40～+110 °C Maximum Power 4 W Resistance to Soldering Heats 10 ( @ 260°C) sec. Polarization Linear Azimuth Beamwidth Omni-directional Termination Cu / Sn (Leadless) 4/11 ONEWAVE TECHNOLOGY CO., LTD. 2. Recommended PCB Pattern Evaluation Board Dimension 2 nd Evaluation Board Dimension Suggested Matching Circuit 重要資訊 : 匹配元件建議使用精準度高的電感±0.1~0.3nH、電容±0.1pF 5/11 ONEWAVE TECHNOLOGY CO., LTD. Layout Dimensions in Clearance area( Size=5.9*5.0mm) FootPrint (Unit : mm) ◆ 2 nd Layout Dimensions in Clearance area( Size=8.0*3.0mm) Matching Circuit 50 ohm transmission Line 6/11 ONEWAVE TECHNOLOGY CO., LTD. 3. Measurement Results Return Loss 7/11 ONEWAVE TECHNOLOGY CO., LTD. Radiation Pattern Efficiency Peak Gain Directivity 2400MHz 81.46% 1.67 dBi 2.56 dBi 2450MHz 84.75% 1.75 dBi 2.46 dBi 2500MHz 82.68% 1.70 dBi 2.52 dBi Chamber Coordinate System X Y Z 8/11 ONEWAVE TECHNOLOGY CO., LTD. 4.Reliability and Test Condictions ITEM REQUIREMENTS TEST CONDITION Solderability 1. Wetting shall exceed 90% coverage 2. No visible mechanical damage Pre-heating temperature:150°C/60sec. Solder temperature:230±5°C Duration:4±1sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Solder heat Resistance 1. No visible mechanical damage 2. Central Freq. change :within ± 6% 10 ± 0.5 sec. 60 sec . . T E M P ( °C ) 150 °C 2 6 0 °C Pre-heating temperature:150°C/60sec. Solder temperature:260±5°C Duration:10±0.5sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Component Adhesion (Push test) 1. No visible mechanical damage The device should be reflow soldered(230±5°C for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component. Component Adhesion (Pull test) 1. No visible mechanical damage Insert 10cm wire into the remaining open eye bend ,the ends of even wire lengths upward and wind together. Terminal shall not be remarkably damaged. Thermal shock 1. No visible mechanical damage 2. Central Freq. change :within ±6% Phase Temperature(°C) Time(min) 1 +110±5°C 30±3 2 Room Temperature Within 3sec 3 -40±2°C 30±3 4 Room Temperature Within 3sec +110°C=>30±3min -40°C=>30±3min Test cycle:10 cycles The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: +110±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature:-40±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Humidity 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: 40±2°C Humidity: 90% to 95% RH Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. 4±1 sec. 60sec TEMP (°C) 150°C 230°C 9/11 ONEWAVE TECHNOLOGY CO., LTD. 5.Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. ‧Preheat circuit and products to 150°C ‧Never contact the ceramic with the iron tip ‧Use a 20 watt soldering iron with tip diameter of 1.0mm ‧280°C tip temperature (max) ‧1.0mm tip diameter (max) ‧Limit soldering time to 3 sec. SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) 60~120 s 10s max. 30~60s 250~260 230 180 150 TIME(sec.) Reflow Soldering SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) within 3s Gradual cooling 150 TIME(sec.) Iron Soldering Over 60s 350 300 10/11 ONEWAVE TECHNOLOGY CO., LTD. 6.Packaging Information Tape Specification: Reel Specification: (7’’, Φ180 mm) Tape Width(mm) A(mm) B(mm) C(mm) D(mm) Chip/Reel(pcs) 8 9.0±0.5 60±2 13.5±0.5 178±2 3000 11/11 ONEWAVE TECHNOLOGY CO., LTD. 7.Storage and Transportation Information Storage Conditions To maintain the solderability of terminal electrodes: 1. Temperature and humidity con…

Text truncated - open the document above for the full version.