2A6OYMEGA1Millimeter Wave Radar

MEGA1 USER MANUAL I. UPON RECEIPT Once you have received the unit, please remove it from the packaging and verify that the following components are also contained within the box: • Radar unit • Base • Rubber grommet II. ORIENTATION AND INSTALLATION Before the device can be plugged in, please follow the orientation and installation guide to place the device at the desired location and angles for usage. Once the unit is appropriately mounted, supply power via a CAT5/CAT6 cable with a PoE supply; the supply can be an injector, router, or switch. III. CONFIGURATION After the unit is connected, you can further configure and setup the parameters by logging in with your supplied credentials to www.omnisightusa.com FCC: 2A6OYMEGA1 IC: 28582-MEGA1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation) The license-exempt transmitter / receiver contained in this device complies with the Innovation, Science and Economic Development Canada NRCs applicable to devices radio exempt from license. Operation is permitted under the following two conditions: (1) The device may not cause interference; (2) The device must accept any interference radio interference, even if the interference may compromise its operation. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IV. Regulatory Information Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by Omnisight, Inc. may void the user’s authority to operate this equipment. Radio Frequency Interface (RFI) (FCC 15.105) This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. RFx warning statement In order to comply with FCC and ISED RF Exposure requirements, a minimum separation distance of 200 cm must be maintained between the device and all persons during normal operation Afin de se conformer aux exigences d'exposition RF FCC et ISED, un minimum une distance de séparation de 200 cm doit être maintenue entre l'appareil et toutes les personnes pendant le fonctionnement normal Suppliers Declaration of Conformity 47 CFR 2.1077 Compliance Information Unique Identifier: 2A6OY-MEGA1 Responsible Party – U.S. Contact Information Omnisight, Inc 295 Seven Farms Drive Suite C-289 Daniel Island, SC 29492 Website: www.omnisightusa.com Contact Email: [email protected]

CERTIFICATION ATTESTATION PAGE 1 OF 1 Certification Application Attestation Statements Date: February 14, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) _Omnisight, Inc.______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) _Omnisight, Inc.______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Thank you, By: Ryan McGarty (Signature 2 ) (Print name) Title: Partner Company: Omnisight, Inc.________ Telephone: _404-408-4265__ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist .

DESIGNATION FOR SERVICE PAGE 1 OF 1 U.S. Agent Designation for Service of Process (Applicant is Both Grantee and U.S. Agent) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Omnisight, Inc. Grantee Code:2A6OY Contact Name: Ryan McGarty Street Address: 295 Seven Farms Drive, Suite C-289 City/Province/Zip: Daniel Island, South Carolina 29492 Telephone No: +404-408-4265 Email: [email protected] Applicant Signature 1 : Date: 2/9/2023 Signed by (Printed Name/Title): Ryan McGarty/Partner

1 PRODUCT NDA AGREEMENT THIS PRODUCT NDA AGREEMENT (this “Agreement”) is made by and between OMNISIGHT, INC., a Delaware limited liability company (“Provider”), and __________________________________________, the individual or entity desiring to install the hardware and software provided by the Provider (“Receiver”). Receiver is agreeing to be bound by the terms and conditions of this Agreement for the hardware and software (“Product”). REQUIREMENTS AND RESTRICTIONS. a) Receiver will not disclose to anyone else (especially any other third-party providers, or independent researchers) any of the Intellectual Property that is part of or associated with in any fashion, the Product. The Intellectual Property includes, without limitation, the display screens, structure, organization and code of the Product, internal photos, all inventorship and authorship rights, patents, patent applications and know-how, copyrights, trademarks and service mark rights inherent in such structure, organization and code and all related data and databases and interfaces. The Intellectual Property of the Product constitutes the valuable trade secrets, confidential business process and confidential information of Provider. That Intellectual Property is or may be protected by law, including but not limited to, the copyright laws of the United States. b) Receiver will not attempt to reverse engineer, decompile, or disassemble any portion of the Product. Receiver will not unbundle, or attempt to unbundle, the component parts of the Demo Product, for distribution, analysis, transfer, resale or otherwise to ANY other third party. c) Receiver will hold in strict confidence and will not disclose the portions of the code, screen shots, descriptions, or other component parts of the Demo Product to anyone else. d) Receiver will hold in strict confidence and will not disclose inner workings of the hardware product to anyone else nor attempt to disassemble the hardware product in any fashion. TERM AND TERMINATIONS. a) Term. This Agreement shall commence on the date that Receiver receives the Product and shall apply in perpetuity. RELATIONSHIP OF THE PARTIES. Nothing in this Agreement shall create, or be deemed to create, a partnership or the relationship of principal and agent or employer and employee between the Parties. Neither Party has the authority or power to bind, to contract in the name of or to create a liability for the other in any way or for any purpose. By signing this document, Receiver acknowledges and agrees in writing to the terms and restrictions of this Agreement. Signed: _________________________________ __________________ Receiver Authorized Management Date Signed: _________________________________ __________________ Omnisight, Inc. Officer Date

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD 050222-17 Authority to Act as Agent Date: February 2, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: _Kimberly Colbert is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 10/1/2023 By: ___ Ryan McGarty_ _________________ (Signature 1 ) (Print name) Title: _Partner_ On behalf of: __ Omnisight, Inc (Company Name) Telephone: __(404) 408-4265 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

REQUEST FOR CONFIDENTIALITY PAGE 1 OF 1 Request for Confidentiality Date: July 22, 2022 Subject: Confidentiality Request for: ___2A6OYMEGA1___ ______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term External Photos ☐ Short Term ☒ Permanent Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term Test Setup Photos ☐ Short Term ☐ Permanent User¶s ManXal ______OmniSight, Inc______ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___180___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: __________________________ _______Ryan McGarty_________________ (Signature/Title) (Print name)

Label Details The label affixed to the devices is an extremely durable waterproof vinyl sticker with an adhesive intended for long term use.

HVIN: MEGA-ANT-V4 87KJ99A FCC ID: 2A6OYMEGA1 IC ID: 28582-MEGA1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

MPE TEST REPORT for the OMNISIGHT, INC. FCC ID: 2A6OYMEGA1 IC ID: 28582-MEGA1 WLL REPORT# 17411-01 REV 1 Prepared for: OmniSight, Inc. 8007 S. Fairfax Court Centennial, Colorado 80122 Prepared By: Washington Laboratories, Ltd. 4840 Winchester Boulevard. Ste# 5 Frederick, Maryland 21703 Testing Certificate AT-1448 Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, Ltd OmniSight, Inc. MegaRadar V1 MPE Test Report WLL Report 17411-01 Rev 1 Page-2 of 13 MPE Test Report for the OmniSight, Inc. – MegaRadar V1 FCC ID: 2A6OYMEGA1 ISED ID: 28582-MEGA1 April 29, 2022 WLL Report# 17411-01 Rev 1 Prepared by: ___________________________ Ryan Mascaro RF Test Engineer Reviewed by: ____________________________ Steven D. Koster President OmniSight, Inc. MegaRadar V1 MPE Test Report WLL Report 17411-01 Rev 1 Page-3 of 13 Abstract This report has been prepared on behalf of OmniSight, Inc. to document the findings of the maximum permissible exposure evaluation on the 60GHz, MegaRadar V1. The information provided on this report is only applicable to device herein documented. The purpose of this evaluation is to establish a minimum safe distance as per the RF exposure requirements as defined in FCC §1.1307 & §1.1310 and in RSS-102. This report documents the results of testing to the requirements of: • CFR Title 47 Volume 1 Practice and Procedure; (1.1307) Environmental Assessments • RSS-102 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) The evaluation was performed by Washington Laboratories, LTD., located at 4840 Winchester Blvd., Suite 5, Frederick, MD 21703. Washington Laboratories, LTD. has been accepted as an EMC Conformity Assessment Body (CAB) under the United States/European Union Memorandum of Agreement. Washington Laboratories, LTD. has been accepted by the FCC and approved by ANAB under Testing Certificate AT-1448 as an independent FCC test laboratory. Revision History Description of Change Date Rev 0 Initial Release April 29, 2022 Rev 1 ACB Comments October 24, 2022 OmniSight, Inc. MegaRadar V1 MPE Test Report WLL Report 17411-01 Rev 1 Page-4 of 13 Table of Contents Abstract ...................................................................................................................................................... iii Table of Contents ....................................................................................................................................... iv List of Tables ...............................................................................................................................................v 1 Introduction ......................................................................................................................................6 2 Requirements ...................................................................................................................................6 Transmitter Categories ................................................................................................................ 6 2.1.1 Fixed Installations ................................................................................................................... 6 2.1.2 Mobile Devices ....................................................................................................................... 6 2.1.3 Portable Devices ..................................................................................................................... 6 Exposure Categories ................................................................................................................... 7 2.2.1 Occupational/Controlled Exposure ......................................................................................... 7 2.2.2 General Population/Uncontrolled Exposure ........................................................................... 7 3 Device Summary ............................................................................................................................10 4 Radio Frequency Radiation Exposure Evaluation .........................................................................11 OmniSight, Inc. MegaRadar V1 MPE Test Report WLL Report 17411-01 Rev 1 Page-5 of 13 List of Tables Table 1: MPE Limits (FCC) ....................................................................................................................... 8 Table 2: MPE Limits (ISED) ...................................................................................................................... 9 Table 3: Device Summary – MegaRadar V1 ............................................................................................ 10 Table 4: Transmitter MPE Calculation Summary (FCC) ......................................................................... 12 Table 5: Transmitter MPE Calculation Summary (ISED) ........................................................................ 13 OmniSight, Inc. MegaRadar V1 MPE Test Report WLL Report 17411-01 Rev 1 Page-6 of 13 1 Introduction This report has been prepared on behalf of OmniSight, Inc. for the MegaRadar V1, dual-transmitter device, to show compliance with the RF exposure requirements as defined in FCC §1.1307 & §1.1310, and in RSS-102. The testing in-support of this evaluation was performed at Washington Laboratories, LTD. Washington Laboratories, Ltd. has been accepted as an EMC Conformity Assessment Body (CAB) under the United States/European Union Memorandum of Agreement. Washington Laboratories, LTD. is accredited with ANAB under Testing Certificate AT-1448. 2 Requirements Transmitter Categories 2.1.1 Fixed Installations A fixed location means that the device, including its antenna, is physically secured at a permanent location and is not able to be easily moved to another location. Additionally, distance to humans from the antenna is maintained to at least 2 meters. 2.1.2 Mobile Devices A mobile d…

Text truncated - open the document above for the full version.

12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 1/6 Introduction IWR6843ISK EVM antenna is designed to be operated in 60GHz frequency range. The use cases which can be addressed with this antenna are fluid level sensing, industrial automation, motion detection etc. Design Azimuth FOV Elevation FOV Azimuth Angular Elevation Angular Max Distance for Person (m) ** (deg)* (deg)* Resolution(deg) Resolution (deg) IWR6843ISK +/-60 +/-15 15 58 75 (60GHz) A comparison table of all antenna configurations can be on the Industrial Toolbox Antennas overview page (../../antennas_landing.html). IWR6843ISK EVM Antenna Picture & Dimensions 12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 2/6 Close-up of applicant’s antenna array to show it is the same as the MIMO antenna array. The antenna peak gain of IWR6843ISK EVM Antenna is about 7 dBi across the operating frequency band of 60 GHz. For more details about this EVM, please refer to the following link: http://www.ti.com/tool/iwr6843isk (http://www.ti.com/tool/iwr6843isk) IWR6843ISK EVM Stackup Please refer to below PCB stackup details for IWR6843ISK Antenna. 12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 3/6 The mmWave layer is Rogers RO4835 with LoPro copper. ED (electro-deposited) copper is not a suitable material for mmWave frequencies. Detailed layout of this antenna with stackup are available for you to download and reuse at the following link: http://www.ti.com/lit/zip/swrc355 (http://www.ti.com/lit/zip/swrc355) Measured Radiation Patterns Measured radiation patterns of IWR6843ISK EVM Antenna for Elevation and Azimuth can be seen below. 12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 4/6 12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 5/6 In the above pictures X axis represents the angle (in degrees) and Y axis represents the normalized gain (in dB). This radiation pattern is measured inside a Anechoic chamber with a corner reflector. The FMCW chirp used for this measurement has a start frequency of 60GHz and a RF bandwidth of 2GHz. Manufacturing Guidelines 12/22/22, 5:55 PM IWR6843ISK (60GHz) https://dev.ti.com/tirex/content/mmwave_industrial_toolbox_4_10_1/antennas/ant_rad_patterns/iwr6843_isk/iwr6843_isk.html 6/6 The details on manufacturing this antenna can be found in the “TI mmWave Radar Sensor RF PCB Design, Manufacturing and Validation Guide" - http://www.ti.com/lit/pdf/spracg5 (http://www.ti.com/lit/pdf/spracg5) Board Manufacturer Streamline Circuits (Now part of Summit Interconnect)- https://www.summit-pcb.com/ (https://www.summit-pcb.com/) Material Details Rogers Corporation - https://www.rogerscorp.com/ (https://www.rogerscorp.com/)

FCC §15.255 AND ISED CANADA RSS-210 CERTIFICATION TEST REPORT for the MEGARADAR V1 FCC ID: 2A6OYMEGA1 IC ID: 28582-MEGA1 WLL REPORT# 17410-01 REV 2 Prepared for: OmniSight, Inc. 8007 S. Fairfax Court Centennial, Colorado 80122 Prepared By: Washington Laboratories, Ltd. 4840 Winchester Boulevard. Ste # 5 Frederick, Maryland 21703 Testing Certificate AT-1448 Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, Ltd OmniSight, Inc. MegaRadar V1 FCC §15.255 Certification Test Report WLL Report 17410-01 Rev 2 Page-2 of 64 FCC §15.255 and ISED Canada RSS-210 Certification Test Report for the OmniSight, Inc. MegaRadar V1 FCC ID: 2A6OYMEGA1 IC ID: 28582-MEGA1 April 15, 2022 WLL Report# 17410-01 Rev 2 Prepared by: ___________________________ Ryan Mascaro RF Test Engineer Reviewed by: ____________________________ Steven D. Koster President OmniSight, Inc. MegaRadar V1 FCC §15.255 Certification Test Report WLL Report 17410-01 Rev 2 Page-3 of 64 Abstract This report has been prepared on behalf of OmniSight, Inc. to support the attached Application for Equipment Authorization. The test report and application are submitted for a Fixed Field Disturbance Sensor (Radar) Transmitter under Part 15.255 of the FCC Rules and Regulations and Spectrum Management and Telecommunications Policy and under RSS-210, Issue 10 (12/2019) of Innovation, Science and Economic Development Canada (ISED). This Certification Test Report documents the test configuration and test results for the OmniSight, Inc. MegaRadar V1, in the High Power Mode. The information provided on this report is only applicable to device herein documented, as the EUT. Radiated testing below 40 GHz was performed in the Free-space Anechoic Chamber Test-site (FACT) 3m Chamber of Washington Laboratories, Ltd., located at 4840 Winchester Boulevard, Suite #5. Frederick, MD 21703. Site description and site attenuation data are currently being reported to the FCC's Sampling and Measurements Branch at the FCC laboratory in Columbia, MD. Washington Laboratories, Ltd. has been accepted by the FCC and approved by ANAB under Testing Certificate AT-1448 as an independent FCC test laboratory. The Washington Laboratories, Ltd. ISED Canada number is 3035A. The OmniSight, Inc. MegaRadar V1 complies with the limits and requirements for a Fixed Field Disturbance Sensor (Radar) Transmitter under Part 15.255 of the FCC Rules and Regulations and Innovation, Science and Economic Development Canada (ISED) RSS-210, Annex J, Issue 10 (12/2019). Revision History Description of Change Date Rev 0 Initial Release April 15, 2022 Rev 1 Amendments per ACB Comments, dated: 9/29/2022 October 24, 2022 Rev 2 Amendments to the EUT Block Diagram, per ACB Comments November 7, 2022 OmniSight, Inc. MegaRadar V1 FCC §15.255 Certification Test Report WLL Report 17410-01 Rev 2 Page-4 of 64 Table of Contents 1 Introduction ..................................................................................................................................... 7 1.1 Compliance Statement ................................................................................................................ 7 1.2 Test Scope ................................................................................................................................... 7 1.3 Contract Information ................................................................................................................... 8 1.4 Test and Support Personnel ........................................................................................................ 8 1.5 Test Dates.................................................................................................................................... 8 1.6 Test Location .............................................................................................................................. 8 1.7 EUT Digital Emissions ............................................................................................................... 8 2 Test Results ..................................................................................................................................... 9 2.1 AC Mains Conducted Emissions ................................................................................................ 9 2.2 RDR255 – Fixed Use Operation ............................................................................................... 12 2.3 Transmitter Occupied Bandwidth ............................................................................................. 13 2.4 Transmitter Power Within the Operational Band ..................................................................... 17 2.5 Peak Transmitter Conducted Output Power ............................................................................. 21 2.6 Transmitter Power Outside the Operational Band .................................................................... 22 2.7 Spurious Emissions, 40 GHz – 200 GHz .................................................................................. 30 2.8 Spurious Emissions Below 40 GHz .......................................................................................... 46 2.9 Frequency Stability ................................................................................................................... 53 2.10 Transmitter Duty Cycle Correction Factor (DCCF) ................................................................. 55 3 Equipment Under Test .................................................................................................................. 57 3.1 EUT Identification & Description ............................................................................................ 57 3.2 Testing Algorithm ..................................................................................................................... 57 3.3 Test Configuration ..........................................…

Text truncated - open the document above for the full version.

FCC §15.255 AND ISED CANADA RSS-210 CERTIFICATION TEST REPORT for the MEGARADAR V1 FCC ID: 2AYO6MEGA1 IC ID: 28582-MEGA1 WLL REPORT# 17557-01 REV 2 Prepared for: OmniSight, Inc. 8007 S. Fairfax Court Centennial, Colorado 80122 Prepared By: Washington Laboratories, Ltd. 4840 Winchester Boulevard. Ste # 5 Frederick, Maryland 21703 Testing Certificate AT-1448 Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, Ltd OmniSight, Inc. MegaRadar V1 FCC §15.255 Certification Test Report WLL Report 17557-01 Rev 2 Page-2 of 75 FCC §15.255 and ISED Canada RSS-210 Certification Test Report for the OmniSight, Inc. MegaRadar V1 FCC ID: 2AYO6MEGA1 IC ID: 28582-MEGA1 May 6, 2022 WLL Report# 17557-01 Rev 2 Prepared by: ___________________________ Ryan Mascaro RF Test Engineer Reviewed by: ____________________________ Steven D. Koster President OmniSight, Inc. MegaRadar V1 FCC §15.255 Certification Test Report WLL Report 17557-01 Rev 2 Page-3 of 75 Abstract This report has been prepared on behalf of OmniSight, Inc. to support the attached Application for Equipment Authorization. The test report and application are submitted for a Fixed Field Disturbance Sensor (Radar) Transmitter under Part 15.255 of the FCC Rules and Regulations and Spectrum Management a…

Text truncated - open the document above for the full version.