2A6TO-QC3Wireless Bluetooth Adapter

"T
TIPX
JO
UIF
QJDUVSF
QVU
UIF
BEBQUFS
JOUP
ZPVS
IFBEQIPOF <UR[SK;V <UR[SK*U]T 3/) 6RG_6G[YK([ZZUT 6U]KX([ZZUT 2+*/TJOIGZUX :_VK))NGXMOTM6UXZ '[JOU/TZKXLGIK 1SPEVDU
%FUBJMT
&OHMJTI 6TJOH
8BZ 1SPEVDU
/VNCFS
2$ 
7  ̰Long press the power button for 3 seconds to power on the adapter. ̰Please keep the adapter and the cellphone in the range of 1 meters if it's the first pairing. ̰ The red and blue lights flash alternately when entering the pairing mode after adapter power on ( if it doesn't enter pairing mode, please long press the Vol"+" and Vol"-" button at the same time for 3 seconds until the red and blue lights flash alternately) *Please refer to the “Enter pairing mode” in “Basic Operation” table on page 4 ̰Open the BT set on your cell phone or the devices with BT function. Then search the BT devices and choose pairing name “ QC3 ”. Enter “0000” pin code if needed. ̰ The blue LED flash slowly when it's paired successfully. Note: 1.When the distance between the adapter and the BT devices is far than 10 meters or 33 feet, the adapter will disconnect from the devices.After that, once the they are in the range of 33 feet, they will automatically reconnect. 2.If the headphones has paired, you can force the adapter “Enter pairing mode” again which other cellphone can find the adapter and connect it. 1BJSJOH
.FUIPE $POOFDU
5XP
%FWJDFT ̰Follow the pairing method, pair the first cellphone and then “Enter pairing mode” again to pairing the second cellphone. ̰Enter the cellphone setting interface of the first cellphone, and connect the device QC3 again. With a Type-C cable(attach with the package)to connect the adapter and the USB port of your PC or charging source, the adapter will be charged. it takes 2 hours for full charging.When charging, the LED indicator is RED, after charging finished , the LED indicator will turn to BLUE. Note: 1.Because the battery may lose some power in the storage, here kindly suggest charging your adapter full before the first time you use it. 2.When charging, the adapter can not be used. 3.If not use adapter for a long time, suggest charging it once a month to keep battery life. Red led flash quickly: low power Keeping red led light: charging Keeping blue led light: charging complete Blue led and red led flashing alternately: pairing mode Blue led flashing slowly: connected/calling/playing music Blue led flashing quickly: incoming call Blue led double flashing slowly: the adapter doesn't connect the cellphone $IBSHJOH
.FUIPE -&%
*OEJDBUPS 1SPEVDU
"DDFTTPSJFT
64#
DBCMF
64#
UP
5ZQFD
Play time: 6~8 hours(depending on the actual volume and the sound source) Charging time: 2 hours Standby time: Up to 10 days Effective range: 10 meters(33 feet) 4QFDJDBUJPO #BTJD
0QFSBUJPO Adapter button controller OpeationWarning tone Long press Power button for 3 seconds Long press Power button for 3 seconds Click the Play/Pause button Click the Play/Pause button Click the Play/Pause button Power on Power off No Buzzing No Buzzing No Buzzing No Buzzing No Buzzing Paired Dingdong Dudu more times Long press the Vol"+" and Vol"-" button at the same time for 3 seconds Ready to pair Click the Vol “+” / “-” button Power on Power off Answer a call End a call Reject a call Volume control Play or pause the music play( ) * Next song Previous song Low battery BT paired BT disconnected Enter pairing mode Double press Play/Pause button fast within 0.5 seconds Long press the Vol “+” button for 2 seconds Long press the Vol “-” button for 2 seconds ̰G ̰G ̰G ̰G ̰G ̰G ̰G Please store the wireless adapter in a cool, dry place. The working temperature is -10~45 C(14~113 F). In cold or hot highly humid place will reduce the battery life. When long time storage, please charge it before using. Adapter resistance to water, but not waterproof, please don't put the adapter into water. If there is water on it, please use soft cloth to wipe clean. Use soft dry cloth to clean adapter Do not use any sharp objects in connect with adapters. Do not put adapter at a higher or lower temperature. Do not charge the adapter in the moist environment. Can not power on Can not automatic connection Can not discover adapter Not enter pairing mode Check whether the battery is low Check if enters standby mode Charging it Double click on the Play/Pause button to reconnect or power on once again Long press the Vol"+" and Vol"-" button at the same time for 3 seconds 'BVMU
%JBHOPTJT
BOE
4PMVUJPO 4UPSBHF

.BJOUFOBODF *Because of the different operation system and music player, this feature may be different. 1.There is a manual and warranty card in the package. User fill out the warranty card as the warranty certificate. 2.When adapter quality problems occur in normal use and not more than a year sine the date of purchased, users can enjoy free repair services. 3.Which of the following don’t belong to the scope of warranty: A. Warranty card without dealer signature or seal B. Artificial or force majeure cause damage. C. Machine to normal wear and tear. 4.Such as the failure of human, more than the warranty period and irresistible reasons, we will collect repair costs. 5.If the product be send back to factory for repair , please contact us, and fill the warranty cards with your name, address, telephone and fault phenomena. 1SPEVDU
8BSSBOUZ 8BSSBOUZ
5FSNT Product Name: Product Model Number: QC3 Purchase Date: Invoice Number: Customer Name: Customer Phone: Customer Address: 榾嶏꜄ 俪⢦䲭䷒꜄ -&%䧗炐愉 5ZQF$⩘榾⹾ ꮠ겐䬤⹾ ꮠꄈ

ꮠꄈ 뜷⩡곽 ✳榫亡䌋 ⻤ꮠ╵䣒榾陚曻崅䡖环⛮㚜ꮠ洡顏ꮠ䷞岳俏ꧠ䳉ն 㞝㎂炐㵨鴠鿥媯浔繰儬氳┖亡㵨ꮠ겐⹾䬤⪍繰儬ն ◲鬼炐䙬㎂ 甏⛮ 1 ͆Ꝛ䧝榾嶏꜄

熯䋯⻪鴠鿥ն ̰GG鴠鿥鿥㵒休陴㵨鴠鿥♔⹖䣆儬氳饄熊䫝⯆㏇

眦氳葶㍴⫂ն ̰GG䋯儬鲽⪍鿥㵒嘗䌋篍衹愉◬僀ꠇ憭ն㞝冽媆僗⭴朆陴⺱休䧝 ꮠꄈ 示ꮠꄈ꜄

熯ꙵ波⮽篍衹愉◬僀ꠇ憭
陴⹇縓瑭

건䳩⛼䬠炐辑劲╈鲽⪍鿥㵒嘗䌋䳩⛼ն ̰GG䣒䋯䣆儬氳
#5Ⱶ耇䮣碠
#5阻㚷ն鴲䦫2$阻㚷㞝冽꧎金 鰟⪍鿥㵒溞陴鰟⪍鿥㵒㜊題⺵ꄆ㛄┕ꪫ氳䳩⛼ն ̰GG鿥㵒䡗Ⱶ⺵衹愉䜈ꠇն 嫱䙬 澝䎎┚阻㚷氳鳀䫙饄熊飃⭴#5氳僗䷞饄熊眦䡝
葏㶸休鴠 鿥㵨┚阻㚷亇䋯鳀䫙ն塝⺵┉份㱚♜⫋埠㚲◇#5僗䷞饄熊葶㍴ ⫂㱚♜⚢舅ⲁꄆ亍鳀䫙⛙佭㞝冽鴠鿥┚䢦鳀阻㚷亇䋯飃鲋 
⮇ꙵ䖻⺎耇꧎金⹙⭵䲭䷒俪⢦꜄
♔ꄆ亍鳀䫙阻㚷ն 澝㞝冽鴠鿥鳀䫙鲋阻㚷ն⫋埠䣒䋯休
鴠鿥⚢舅ⲁ㍑鳀┕┉
埠氳 #5阻㚷ն 澝㞝冽䋯儬鿥㵒䡗Ⱶ⺵⫋埠鲽⪍鿥㵒嘗䌋塝休⮷…

Text truncated - open the document above for the full version.

ShenzhenMiheyouMaoyiCo.,Ltd Qianhaishenganghezuoqu,qianwanyilu,1hao,Adong,201shi,Shenzhen,Guangdong,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:Sep.04,2023 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2A6TO-QC3 ProductName:WirelessBluetoothAdapter ModelName:QC3 [ShenzhenMiheyouMaoyiCo.,Ltd](“theapplicant”)certifiesthattheequipmentforwhich authorizationissoughtisnot“covered”equipmentprohibitedfromreceivinganequipment authorizationpursuanttosection2.903oftheFCCrules. Sincerely, (Applicantsignature) Name:OscarWen Title:GeneralManager

ShenzhenMiheyouMaoyiCo.,Ltd Qianhaishenganghezuoqu,qianwanyilu,1hao,Adong,201shi,Shenzhen,Guangdong,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:Sep.04,2023 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2A6TO-QC3 ProductName:WirelessBluetoothAdapter ModelName:QC3 [ShenzhenMiheyouMaoyiCo.,Ltd](“theapplicant”)certifiesthat,asofthedateofthefilingofthe application,theapplicantisnotidentifiedontheCoveredListasanentityproducing“covered” equipment. Sincerely, (Applicantsignature) Name:OscarWen Title:GeneralManager

Shenzhen Miheyou Maoyi Co., Ltd Qianhaishenganghezuoqu, qianwanyilu, 1hao, Adong, 201shi, Shenzhen, Guangdong, China Agent Authorization Company: Shenzhen Miheyou Maoyi Co., Ltd Address: Qianhaishenganghezuoqu, qianwanyilu, 1hao, Adong, 201shi, Shenzhen, Guangdong, China Product Name: Wireless Bluetooth Adapter Model Number(s): QC3 Product Description: Wireless Bluetooth Adapter We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Sep. 04, 2023 Name: Oscar Wen Title: General Manager Company: Shenzhen Miheyou Maoyi Co., Ltd

ShenzhenMiheyouMaoyiCo.,Ltd Qianhaishenganghezuoqu,qianwanyilu,1hao,Adong,201shi,Shenzhen,Guangdong, China OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:Sep.04,2023 Subject;RequestforConfidentiality FCCID:2A6TO-QC3 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:OscarWen Title:GeneralManager

Report No.: AGC14259230701AP03 Page 1 of 4 EXTERNAL PHOTOS WHOLE VIEW OF EUT TOP VIEW OF EUT Report No.: AGC14259230701AP03 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC14259230701AP03 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC14259230701AP03 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 10mm*10mm FCC ID: 2A6TO-QC3

Report No.: AGC14259230701AP03 Page 1 of 4 INTERNAL PHOTOS VIEW OF EUT(PORT) OPEN VIEW OF EUT Report No.: AGC14259230701AP03 Page 2 of 4 VIEW OF BATTERY INTERNAL VIEW OF EUT (FIGURE 1) BT Antenna Report No.: AGC14259230701AP03 Page 3 of 4 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC14259230701AP03 Page 4 of 4 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2A6TO-QC3 Product Description Wireless Bluetooth Adapter Model Name QC3 Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others (NFC:13.56MHz) Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Max. Output Power 3.047dBm (Max) Antenna Gain 5.62dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [if(GHz)] s 3.0 for 1-g SAR and ñ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances ñ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT Test Mode Channel Frequency (MHz) Max Output power (dBm) Max Output power (mW) Calculati on Value (Note 1) Threshold Value GFSK BT_BR 2441 3.047 2.017 0.629 3.0 Note 1: Calculation Value =[(max. power of channel, mW)/(min. test separation distance, mm)] ·[√f(GHz)]. Fox example: 2.017/5*√2.441=0.629 ≤ 3.0 According to KDB447498 D01 V06, threshold at which no SAR required is ≤3.0 for 1-g SAR, separation distance is 5mm, and no simultaneous SAR measurement is required. 5. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

-1- 产品技术规格书 SPECIFICATION 拟制 Preparedby ：审核 Checkedby ：批准 Approvedby ： 送样日期 FormedOn 产品版本 DocumentVersion (V1.1) 产品型号PARTNO： 客户料号CUSTOMERPARTNO： 客户确认CUSTOMERAPPROVEDBY： 确认日期APPROVEDDATE： LTA312450-P38 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -2- 目录 Tableofcontents 规格书版本更改记录Versionrejiggertrackrecord..............................3 1.概述Introduction..................................................................4 2.型号PartNumber...............................................................4 3.外型尺寸及测试板焊盘尺寸D i m e n s i o n s.....................4～5 4.测试电路和匹配电路EvaluationBoardandMatchingCircuits............5 5.电气性能ElectricalCharacteristics..........................................6 6.特性曲线Characteristiccurve...................................................6 7.方向图RadiationPattern...................................................7～8 8.可靠性试验后允许误差PostDependabilityTolerance...............9 9.可靠性试验DependabilityTest..........................................9～10 10.回流焊温度ReflowSolderingStandardCondition.....................10 11.包装尺寸PackagingandDimensions....................................11 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -3- 产品规格书版本更改记录 Versionrejiggertrackrecord 版本号 Version 更改记录Rejigger 拟制 Prepared 批准 Approve 日期 Date V1.0首次发行罗昌桅唐雄心2015.8.11 备注： 1、更改产品电性能指标时，版本号需更换（V1.0换为V2.0、V3.0......）； 2、更改产品测试方法（包括可靠性测试条件），或更改使用条件时，当前版本号加系列（V1.0 换为V1.1、V1.2......）。 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -4- 产品尺寸/Size：3.2×1.6×0.6 1.概述 INTRODUCTION " 佳利 " 微波多层陶瓷天线 LA 系列产品设计用于 WLAN 、 WiFi 、蓝牙、 PHS ，手机 多频天线 ,FM 等小体积 SMD 片式设计。 "GLEAD"MicrowaveMulti-LayerCeramicAntennaLAseriesaredesignedtobeused inWLAN 、 WiFi 、 Bluetooth 、 PHS 、 Multiple-bandMobilephoneantenna,FM,etcand compactsizeSMDchipdesign. 2.型号 PartNumber LTA312450-P38 3.外型尺寸及测试板焊盘尺寸 Dimensions （ Unit ： mm ） 天线频率/AntennaFrequency:2450MHz 多层结构天线/Multi-layerAntenna 产品名称，编号/Proudct Name 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -5- 4.测试电路和匹配电路 EvaluationBoardandMatchingCircuits 5.6nH 0.5pF Unit:mm 50ΩFeeding Line GND VIA πType Matching Network Clearance Area 5.0 6.0 1.25 1 . 8 2.25 0 . 7 4 0 . 7 4 3 . 3 4 3 . 7 7 1.0 1.63 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -7- 7. 方向图及效率 RadiationPattern&Efficiency coordinates： X-ZPlanePlane X-YPlane 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -8- Y-ZPlane 3DRadiationPattern Frequency (MHz) 240024502500 Avg.Gain (dBi) -1.56-1.28-1.15 PeckGain (dBi) 5.625.544.48 Efficiency (%) 71.873.575.6 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -9- 8可靠性试验后允许误差PostDependabilityTolerance 经可靠性试验后允许比起始读数偏差见下表 No.Item （项目） PostDependabilityTolerance ( 可靠性试验后允许附加误差 ) 8.1CentralFrequency中心频率±5MHz 8.2BandWidth通带宽度±5MHz 8.3Gain增益±0.1dBi 8.4V.S.W.R(inBW)驻波比±0.1 PostDependabilityTolerance(Refertothetable) 9 可靠性试验 DependabilityTest 基准条件：温度范围Temperaturerange25±5°C 相对湿度范围RelativeHumidityrange55~75%RH 工作温度OperatingTemperaturerange-40°C~+85°C 贮藏温度StorageTemperaturerange-40°C~+85°C 9.1耐振动VibrationResist 在振动频率为10~55Hz振幅为1.5mm沿X.Y.Z方向各振动2小时后测试符合表9.1~9.4规定。 Thedeviceshouldsatisfytheelectricalcharacteristicsspecifiedinparagraph9.1~9.4afterappliedto thevibrationof10to55Hzwithamplitudeof1.5mmfor2hourseachinX,YandZdirections. 9.2耐跌落冲击DropShock 在100cm高度处按X，Y，Z三个面分别自由跌落在木制地板上共3次后测试符合表9.1~9.4规 定。 Thedeviceshouldsatisfytheelectricalcharacteristicsspecifiedinparagraph9.1~9.4afterdropping ontothehardwoodenboardfromtheheightof100cmfor3timeseachfacetofthe3dimensionsofthe device. 9.3耐焊接热SolderHeatProof 能承受经120~150°C的温度预热120秒后，在255°C+10°C的焊锡浸5±0.5秒，或300°C-10°C的 电烙铁焊接3±0.5秒，焊接面无损伤。 Thedeviceshouldbesatisfiedafterpreheatingat120°C~150°Cfor120secondsanddippingin solderingSnat255°C+10°Cfor5±0.5seconds，orelectriciron300°C-10°Cfor3±0.5seconds， withoutdamnify. 9.4结合力试验TensileStrengthofTerminal 在产品电极端子上或表面上应能承受1kg垂直拉力10±1秒。 Thedeviceshouldnotbebrokenaftertensileforceof1.0kgisslowlyappliedtopullaleadpinof thefixeddeviceintheleadaxisdirectionfor10±1seconds. 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -10- 9.5耐弯曲试验BendingResistTest 将产品按图焊在1.6±0.2mm的PCB板中间，由箭头方向施 力：1mm/S，弯曲距离：1.5mm，保持5±1S，产品金属层无脱落。 WeldtheproducttothecenterpartofthePCBwiththethickness 1.6±0.2mmastheillustrationshows,andkeepexertingforce arrow-wardonitatspeedof:1mm/S,andholdfor5±1Satthe positionof1.5mmbendingdistance,sofar,anypeelingoffofthe productmetalcoatingshouldnotbedetected. 9.6耐湿热特性MoistureProof 在温度为60±2°C，相对湿度90~95%的恒温湿箱中放置96小时，在常温中恢复1~2小时后测 试，符合表9.1~9.4规定。 Thedeviceshouldsatisfytheelectricalcharacteristicsspecifiedinparagraph9.1~9.4afterexposedto thetemperature60±2°Candtherelativehumidity90~95%RHfor96hoursand1~2hoursrecoverytime undernormalcondlition. 9.7高温特性HighTemperatureEndurance 在温度为85±5°C的恒温箱中放置96±2小时，在常温中恢复1~2小时后测试。符合表9.1~9.4 规定。 Thedeviceshouldsatisfytheelectricalcharacteristicsspecifiedinparagraph9.1~9.4afterexposedto temperature85±5°Cfor96±2hoursand1~2hoursrecoverytimeundernormaltemperature. 9.8低温特性LowTemperatureEndurance 在温度为-40°C±5°C低温箱中放置96±2小时后恢复1~2小时测试符合表9.1~9.4规定。 Thedeviceshouldalsosatisfytheelectricalcharacteristicsspecifiedinparagraph9.1~9.4afterexposed tothetemperature-40°C±5°Cfor96±2hoursandto2hoursrecoverytimeundernormaltemperature. 9.9温度循环TemperatureCycleTest 在-40°C温度中保持30分钟，再在+85°C温度中保持30分钟，共循环5次后在常温中恢复1~2 小时后测试符合表9.1~9.4规定。 Thedeviceshouldalsosatisfytheelectricalcharacteracticsspecifiedinparagraph9.1~9.4after exposedtothelowtemperature-40°Candhightemperature+85°Cfor30±2mineachby5cyclesand1 to2hoursrecoverytimeundernormaltemperature. 10 回流焊温度 ReflowSolderingStandardCondition 深圳市森美嘉电子有限公司 13510385948 [email protected] JIA XING GLEAD ELECTRONICS CO.,LTD -11- 11包装尺寸(3216)PackagingandDimensions 11.1PlasticTape 包装说明：RemarksforPackage 载带尾部空穴长度150～200mm，载带头部空穴长度250～300mm，头部的盖带加长250mm。 Reservealengthof150~200mmforthetrailerofthecarrierand250~300mmfortheleaderofthe carrierandfurther250mmofcovertapeatt…

Text truncated - open the document above for the full version.

Page 1 of 65 FCC Test Report Report No.: AGC14259230701FE03 FCC ID : 2A6TO-QC3 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Wireless Bluetooth Adapter BRAND NAME : N/A MODEL NAME : QC3 APPLICANT : Shenzhen Miheyou Maoyi Co., Ltd DATE OF ISSUE : Jul. 28, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC14259230701FE03 Page 2 of 65 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 28, 2023 Valid Initial Release Report No.: AGC14259230701FE03 Page 3 of 65 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH .............................................................................................................. 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ......................................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ......................................................... 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................... 8 2.7. TEST METHODOLOGY ............................................................................................................................. 8 2.8. SPECIAL ACCESSORIES ......................................................................................................................... 8 2.9. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.10. ANTENNA REQUIREMENT..................................................................................................................... 8 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 9 4. DESCRIPTION OF TEST MODES ................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 11 5.1. CONFIGURATION OF EUT SYSTEM ...................................................................................................... 11 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 11 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 11 6. TEST FACILITY .............................................................................................................................................. 12 7. PEAK OUTPUT POWER ................................................................................................................................ 13 7.1. MEASUREMENT PROCEDURE ............................................................................................................. 13 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 13 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 14 8. 20DB BANDWIDTH ........................................................................................................................................ 19 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 19 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 19 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 20 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 25 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 25 Report No.: AGC14259230701FE03 Page 4 of 65 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 25 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 25 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 25 10. RADIATED EMISSION ................................................................................................................................. 46 10.1. MEASUREMENT PROCEDURE ........................................................................................................... 46 10.2. TEST SETUP ......................................................................................................................................... 48 10.3. LIMITS AND MEASUREMENT RESULT ............................................................................................... 49 10.4. TEST RESULT........................................................................................................................................ 49 11. NUMBER OF HOPPING FREQUENCY .........................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC14259230701AP02 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC14259230701AP02 Page 2 of 2 RF CONDUCTED TEST SETUP ****************************************End of Report*************************************