2A6XZ-LAGOFRAME0133 inch Frame

About your product The Lago Display is the touchpoint of the Lago ecosystem that affords users the ability to buy, sell, trade, and most importantly enjoy their minted digital artworks. Once wall mounted the display can be controlled with the Lago app, or with the gesture camera (not included). A digital copy of this document, product shelf life, and after sales service can be accessed online by following this QR code or visiting lagoframe.com/warranty. CAUTION This fitness Display is for use only with Lago Digital, Inc. frame cleat with M4 L38mm screws. Use with other wall mount bracket / stand may result in instability causing injury. Do not cover Ventilation openings. This equipment is not intended to be used on soft support. The mains plug/appliance inlet is used as the disconnect device, The socket-outlet shall be installed near the equipment and shall be easily accessible. The DC OUT location which will be connected to end product, shall comply with the requirements of applicable clause for standard IEC 62368-1 Protective earthing terminal. The apparatus should be connector to a mains socket outlet with a protective earthing connection. The symbol indicates AC voltage The symbol indicates DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. FCC WARNINGS: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC WARNINGS: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. CAN ICES-3 (B)/NMB-3(B) This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d’IC RSS-102 sur l’exposition aux radiations qui sont déterminées pour un environnement non contrôlé. Cet équipement doit être installé et utilisé en observant une distance minimum de 20 cm entre la source du rayonnement et votre corps. The device for operation in the band 5150–5350 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5350 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. In the box 1. Screen X1 2. top frame piece X1 3. side frame piece X2 4. bottom frame piece X1 5. power cord X1 6. frame cleat X1 7. frame cleat hardware M4 L38mmX6 8. Handles X2 9. quick start guideX1 10. soundbar hook X1 11. I/O panelX1 Hanging your LAGO display 1. Remove the cleat from the box and attach it to the wall where you’d like your Lago Display to be mounted. Mount the cleat with the creased edge facing upwards and outwards. Use the included hardware （ M4 L38mm ） to mount in at least 4 of the 6 horizontal slot locations, including the top 2 slots. Make sure your Lago Display is mounted into studs or using drywall anchors. 2. Remove the Lago Display from the box using the handles on the back of the product, and mount the display onto the cleat using the notches in the tops of the handles. Do not lift the product from any other location, as this may damage the display. Turning on your LAGO display 1. Use the provided cable to provide power to the Lago Display. First plug in the cord to the “AC IN” input on the back of the display, then …

Text truncated - open the document above for the full version.

Software Security Description – KDB 594280 D02v01r03 Section II General Description 1. Describe how any software/firmware updates for elements than can affect the device’s RF parameters will be obtained, downloaded, validated and installed. For software that is accessed through manufacturer’s website or device’s management system, describe the different levels of security as appropriate. A: There is only one way to download firmware: =>Put RF Module on unique jig to update firmware by download software. 2. Describe the RF parameters that are modified by any software/firmware without any hardware changes. Are these parameters in some way limited such that any other software/firmware changes will not allow the device to exceed the authorized RF characteristics? A: There is no software provided by the manufacturer that can modify critical radio transmitter parameters. 3. Describe in detail the authentication protocols that are in place to ensure that the source of the RF-related software/firmware is valid. Describe in detail how the RF-related software is protected against modification. A: 1. Firmware are encrypted with integrity check to ensure the validity of its content. 2. Without passing the firmware integrity check, no upgrade will be performed. 4. Describe in detail any encryption methods used to support the use of legitimate RF-related software/firmware. A: Firmware are encrypted with integrity check to ensure the validity of its content. 5. For a device that can be configured as a master and client (with active or passive scanning), explain how the device ensures compliance for each mode? In particular if the device acts as master in some band of operation and client in another; how is compliance ensured in each band of operation? A: It can only be used as a Client. Third-Party Access Control 1. Explain if any third parties have the capability to operate a U.S.-sold device on any other regulatory domain, frequencies, or in any manner that may allow the device to operate in violation of the device’s authorization if activated in the U.S. A: The operation frequency and RF parameter only can be change by unique jig so no any third parties can change it. 2. Describe, if the device permits third-party software or firmware installation, what mechanisms are provided by the manufacturer to permit integration of such functions while ensuring that the RF parameters of the device cannot be operated outside its authorization for operation in the U.S. In the description include what controls and/or agreements are in place with providers of third-party functionality to ensure the devices’ underlying RF parameters are unchanged and how the manufacturer verifies the functionality. A: It is no third-party software or firmware can installation 3. For Certified Transmitter modular devices, describe how the module grantee ensures that host manufacturers fully comply with these software security requirements for U-NII devices. If the module is controlled through driver software loaded in the host, describe how the drivers are controlled and managed such that the modular transmitter RF parameters are not modified outside the grant of authorization. A: Not applicable. Software Configuration Description – KDB 594280 D02v01r03 Section III USER CONFIGURATION GUIDE 1. Describe the user configurations permitted through the UI. If different levels of access are permitted for professional installers, system integrators or end-users, describe the differences. There are no RF parameters can be modified. And there are no different levels of access are permitted for professional installers, system integrators or end-users a. What parameters are viewable and configurable by different parties? There are no RF parameters are viewable and configurable. b. What parameters are accessible or modifiable by the professional installer or system integrators? There are no RF parameters can be modified by the professional installer or system integrators. (1) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized? There are no RF parameters can be modified. (2) What controls exist that the user cannot operate the device outside its authorization in the U.S.? This device is not a professionally installed device. c. What parameters are accessible or modifiable by the end-user? There are no RF parameters can be modified by the end-user. (1) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized? There are no RF parameters can be modified. (2) What controls exist that the user cannot operate the device outside its authorization in the U.S.? The firmware is compiled as binary file and cannot change the RF parameter through this binary file. It is read-only without the change to change the setting. d. Is the country code factory set? Can it be changed in the UI? Yes, the country code is factory set, It can’t be changed in the UI. (1) If it can be changed, what controls exist to ensure that the device can only operate within its authorization in the U.S.? Since it can not be changed in the UI, So there are no this controls. e. What are the default parameters when the device is restarted? The device will record the last user's operation and use this as the default parameter when the device is restarted. These default RF parameters are the parameters of the authorization scope. 2. Can the radio be configured in bridge or mesh mode? If yes, an attestation may be required. Further information is available in KDB Publication 905462 D02. No. It can not be configured in bridge or mesh mode 3. For a device that can be configured as a master and client (with active or passive scanning), if this is user configurable, describe what controls exist, within the UI, to ensure compliance for each mode. If the device acts as a master in some bands and client in others, how is this configured to ensure compliance? The operation b…

Text truncated - open the document above for the full version.

Lago Digital, Inc. 6/6/2022 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 AUTHORITY TO ACT AS AGENT - FCC On our behalf, I appoint Hwa-Hsing (Dongguan) Testing Co., Ltd., to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides still resides with us. Sincerely, Printed name: Aly Han

Lago Digital, Inc. 6/6/2022 Nemko North America, Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY - FCC FCC ID: 2A6XZ-LAGOFRAME01 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules and FCC Guidance document 726920, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT LONG-TERM CONFIDENTIALITY: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation SHORT TERM CONFIDENTIALITY FOR A PERIOD OF 180 DAYS (Note: for the X number of days, you can list up to 180 days, but should not go past the date you start product marketing/sale): Internal Photos External Photos User Manual Test Set-up Photographs When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed: Printed name: Aly Han Title: Senior Project Manager

Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 1 of 7 Project No.: 220214EL03-02 External EUT Photo Test Model: LAGO Frame Genesis Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 2 of 7 Project No.: 220214EL03-02 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 3 of 7 Project No.: 220214EL03-02 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 4 of 7 Project No.: 220214EL03-02 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 5 of 7 Project No.: 220214EL03-02 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 6 of 7 Project No.: 220214EL03-02 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 7 of 7 Project No.: 220214EL03-02

Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 1 of 11 Project No.: 220214EL03-01 EUT Photos Test Model: LAGO Frame Genesis Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 2 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 3 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 4 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 5 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 6 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 7 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 8 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 9 of 11 Project No.: 220214EL03-01 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 10 of 11 Project No.: 220214EL03-01 ANT1 Port: BT/WIFI 2.4G/WIFI 5G ANT2 Port: WIFI 2.4G/WIFI 5G Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 11 of 11 Project No.: 220214EL03-01 ANT2： WIFI 2.4G/WIFI 5G ANT1 : BT/ WIFI 2.4G/WIFI 5G

Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 1 of 7 Test Report No.: 220214EL03-SE-US-01 RF Exposure Report FCC ID: 2A6XZ-LAGOFRAME01 Applicant: Lago Digital, Inc. Address: 530 7th Ave Suite 1001 NY, NY 10018 Manufacturer: Lago Digital, Inc. Address: 530 7th Ave Suite 1001 NY, NY 10018 Product(s): 33 inch Frame Brand(s): N/A Test Model(s): LAGO Frame Genesis Series Model(s): N/A Test Date: Apr. 24, 2022~ May 31, 2022 Issued Date: Jun. 02, 2022 Issued By: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Test Firm Registration No.: 915896 Standards: FCC Part 2 (Section 2.1091) 447498 D04 Interim General RF Exposure Guidance v01 IEEE C95.1 The above equipment has been tested by Hwa-Hsing (Dongguan) Testing Co., Ltd., and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : Reviewed by : Tank Tan Scott He Approved by : Harry Li This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by A2LA or any agency of the federal government.The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 2 of 7 Test Report No.: 220214EL03-SE-US-01 Table of contents Release control record ............................................................................................................................ 3 1 General Information ...................................................................................................................... 4 1.1 General Description of EUT ....................................................................................................... 4 2 RF exposure limit .......................................................................................................................... 5 2.1 MPE calculation formula ............................................................................................................ 6 3 Calculation result of maximum conducted power ......................................................................... 6 Appendix – Information on the Testing Laboratories ................................................................................ 7 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 3 of 7 Test Report No.: 220214EL03-SE-US-01 Release control record Issue No. Reason for change Date issued 220214EL03-SE-US-01 Original Release Jun. 02, 2022 Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 4 of 7 Test Report No.: 220214EL03-SE-US-01 1 General Information 1.1 General Description of EUT Product(s) 33 inch Frame Test Model(s) LAGO Frame Genesis Sample No. HS220509-01-15 Series Model(s) N/A Status of EUT Engineering Prototype Power Supply Rating AC 100~240V/1.2A/ 50~60 Hz 120W Modulation Type WiFi: CCK, DQPSK, DBPSK for DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM Bluetooth: GFSK, π/4 DQPSK,8DPSK Modulation Technology WiFi 2.4GHz: DSSS; OFDM WiFi 5GHz: OFDM Bluetooth: FHSS/BT-LE Transfer Rate Wi-Fi 2.4GHz: 802.11b:11.0/ 5.5/ 2.0/ 1.0Mbps 802.11g: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps 802.11n: up to 300Mbps Wi-Fi 5GHz: 802.11a: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps 802.11n: up to 300Mbps 802.11ac: up to 866.7Mbps Bluetooth: 1Mbps/2 Mbps/3 Mbps Operating Frequency Wi-Fi 2.4GHz: 802.11b, 802.11g, 802.11n (HT20): 2412 ~ 2472MHz 802.11n (HT40): 2422 ~ 2462MHz Wi-Fi 5GHz: 5180MHz ~ 5240MHz; 5260MHz ~ 5320MHz; 5500MHz ~ 5700MHz; 5745MHz ~ 5825MHz Bluetooth: 2402MHz ~ 2480 MHz Output Power (AVG) Wi-Fi 5GHz: 19.45dBm for 5150 ~ 5250MHz 18.97dBm for 5250 ~ 5350MHz 19.18dBm for 5470 ~ 5725MHz 18.99dBm for 5725 ~ 5850MHz Wi…

Text truncated - open the document above for the full version.

Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 1 of 54 Test Report No.: 220214EL03-RF-US-02 FCC Part 15, Subpart C Test Report FCC ID: 2A6XZ-LAGOFRAME01 Applicant: Lago Digital, Inc. Address: 530 7th Ave Suite 1001 NY, NY 10018 Manufacturer: Lago Digital, Inc. Address: 530 7th Ave Suite 1001 NY, NY 10018 Product(s): 33 inch Frame Brand(s): N/A Test Model(s): LAGO Frame Genesis Series Model(s): N/A Test Date: May 03, 2022~ June 15, 2022 Issued Date: June 17, 2022 Issued By: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld. N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Test Firm Registration No.: 915896 Designation No.: CN1255 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10:2013 The above equipment has been tested by Hwa-Hsing (Dongguan) Testing Co., Ltd., and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : Reviewed by : Tank Tan Scott He Approved by : Harry Li This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into the account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by A2LA or any agency of the federal government. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Lab: Hwa-Hsing (Dongguan) Testing Co., Ltd. Address: No.101, Bld N1, Yuyuan 2Rd, Yuyuan Industrial Park, HuangJiang Town, Dongguan, China Tel: 0769-83078199 Web.: www.hwa-hsing.com E-Mail: [email protected] Release Ver. 1.5 Page 2 of 54 Test Report No.: 220214EL03-RF-US-02 Table of Contents Release Control Record .................................................................................................................................. 4 1. Summary of Test Results .......................................................................................................................... 5 1.1 Measurement Uncertainty ..................................................................................................................... 5 1.2 Modification Record .............................................................................................................................. 5 2. General Information ..............................................................................................................................…

Text truncated - open the document above for the full version.