2A7TE-FB-8SWireless Headphone

2 FB-B39 Button instruction Press for 5 seconds Power on when the headphone is power on, press to switch from Bluetooth name to Radio mode Play / Pause Music Answer / Hang up phone call Long press for 2 seconds to decline incoming call Press to move to next track Press and hold volume up Press to move to Previous track Press and hold volume down Socket instruction Micro-USB Charging port TF card socket AUX socket The headphone will turn off if not connected to any bluetooth device for 5 minutes Specification Bluetooth 5.0 Frequency ：2.4 GHz Wireless Support Protocol: A2DP AVRCP V1.5/ HFP V1.6/ HSP V1.2 Battery: 3.7V 200 mAh Charging Time (h) ：1-2 hours Music Time ：4-5 hours Instructions Fully charge the headphone before first use. How to charge Connect to a USB power source using the included micro-usb charging cable When you turn the headphone on , the LED will flash blue and red to indicate pairing mode. 1.Using the Bluetooth menu on your device(phone, computer, tablet, etc.), enable searching for nearby Bluetooth device . 2.Select” B39 ” to connect and pair. NOTE: If your device prompts for a PIN code, enter ”0000”. 3.Once paired , the LED will flash blue and you will hear a tone confirming the successful connection. NOTE: the headphone will automatically reconnect to the last paired Bluetooth audio device when the headphone is turn on. How to Pair Play via AUX Using the included 3.5mm auxiliary cable to connect the headphone to other audio sources including non-bluetooth device. You music will automatically play. NOTE: when wired via AUX , the Bluetooth functions are automatically disable. Use the controls on your source device instead. ENGLISH 2 FB-B39 Button instruction Press for 5 seconds Power on when the headphone is power on, press to switch from Bluetooth name to Radio mode Play / Pause Music Answer / Hang up phone call Long press for 2 seconds to decline incoming call Press to move to next track Press and hold volume up Press to move to Previous track Press and hold volume down Socket instruction Micro-USB Charging port TF card socket AUX socket Specification Bluetooth 5.0 Frequency ：2.4 GHz Wireless Support Protocol: A2DP AVRCP V1.5/ HFP V1.6/ HSP V1.2 Battery: 3.7V 200 mAh Charging Time (h) ：1-2 hours Music Time ：4-5 hours Instrukcja Przed pierwszym użyciem słuchawki należy w pełni naładować Jak ładować Podłącz źródło zasilania USB za pomocą dołączonego kabla micro-USB Parowanie Kiedy włączysz słuchawki, dioda LED zaświeci się na niebiesko i czerwono, co oznacza wejście w tryb parowania. 1.Korzystając z ustawień Bluetooth na swoim urządzeniu (telefon, komputer, tablet itp.), włącz funkcję wyszukiwania urządzeń Bluetooth. 2.Wybierz urządzenie „B39”, aby połączyć się i sparować. UWAGA: Jeśli twoje urządzenie wymaga kodu PIN, wpisz: „0000”. 3.Po sparowaniu dioda LED zaświeci się na niebiesko, usłyszysz dźwięk potwierdzający połączenie. UWAGA: Po włączeniu słuchawki automatycznie połączą z urządzeniem Bluetooth, z którym były sparowane po raz ostatni. Odtwarzanie przez złącze AUX Korzystając z dołączonego kabla AUX 3,5 mm, podłączysz słuchawki do innego źródła dźwięku niewyposażonego w funkcję Bluetooth. Twoja muzyka zostanie odtworzona automatycznie. UWAGA: po przejściu w tryb połączenia AUX funkcje Bluetooth wyłączają się automatycznie. Regulacja dźwięku odbywa się z poziomu urządzenia źródłowego. Słuchawki wyłączą się automatycznie, jeśli w ciągu 5 minut nie połączą się z żadnym urządzeniem Bluetooth. POLISH 2 FB-B39 Button instruction Press for 5 seconds Power on when the headphone is power on, press to switch from Bluetooth name to Radio mode Play / Pause Music Answer / Hang up phone call Long press for 2 seconds to decline incoming call Press to move to next track Press and hold volume up Press to move to Previous track Press and hold volume down Socket instruction Micro-USB Charging port TF card socket AUX socket Specification Bluetooth 5.0 Frequency ：2.4 GHz Wireless Support Protocol: A2DP AVRCP V1.5/ HFP V1.6/ HSP V1.2 Battery: 3.7V 200 mAh Charging Time (h) ：1-2 hours Music Time ：4-5 hours Anleitung Der Kopfhörer muss vor der ersten Anwendung vollständig aufgeladen werden. Aufladen Schließen Sie den Kopfhörer mit dem mitgelieferten Micro-USB-Ladekabel an eine USB-Stromquelle an. Pairing Wenn Sie den Kopfhörer einschalten, blinkt die LED blau und rot, um den Kopplungsmodus anzuzeigen. 1.Aktivieren Sie über das Bluetooth-Menü Ihres Geräts (Telefon, Computer, Tablet usw.) die Suche nach einem Bluetooth-Gerät in der Nähe. 2.Wählen Sie" B39 " zum Verbinden und Koppeln. HINWEIS: Wenn Ihr Gerät Sie zur Eingabe eines PIN-Codes auffordert, geben Sie "0000" ein. 3.Sobald die Verbindung hergestellt ist, blinkt die LED blau und Sie hören einen Ton, der die erfolgreiche Verbindung bestätigt. HINWEIS: Der Kopfhörer verbindet sich automatisch wieder mit dem zuletzt gekoppelten Bluetooth-Audiogerät, wenn der Kopfhörer eingeschaltet wird. Wiedergabe über AUX Verwenden Sie das mitgelieferte 3,5-mm-AUX-Kabel, um den Kopfhörer mit anderen Audioquellen zu verbinden, auch mit Nicht-Bluetooth-Geräten. Ihre Musik wird automatisch abgespielt. HINWEIS: Wenn Sie den Kopfhörer über AUX verkabeln, werden die Bluetooth-Funktionen automatisch deaktiviert. Verwenden Sie stattdessen die Bedienelemente an Ihrem Quellgerät. Der Kopfhörer schaltet sich automatisch aus, wenn er 5 Minuten lang nicht mit einem Bluetooth-Gerät verbunden ist. GERMAN FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the …

Text truncated - open the document above for the full version.

Page 1 of 5 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Fig. 1 Fig. 2 Page 2 of 5 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 5 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 5 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 5 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10

Page 1 of 1 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L4.0cm x 3.0cm) Label Location Wireless Headphone Model: FB-8S FCC ID: 2A7TE-FB-8S

Page 1 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Page 2 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Antenna Page 5 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 6 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 Fig. 12

Page 1 of 4 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC RF Exposure Evaluation 1. Product Information FCC ID : 2A7TE-FB-8S Product name : Wireless Headphone Test Model : FB-8S Additional Model No. : FB-130, FB-SH11, FB-B39, FB-ST36, FB-ST17 Model Declaration : PCB board, structure and internal of these model(s) are the same, So no additional models were tested Power Supply : Input: DC 5V, 150mA DC 3.7V by Rechargeable Li-ion Battery, 200mAh Hardware Version : AC692x_SDK_V2.3.1 Software Version : DX-8S-AC25F-V1.0 Bluetooth : 2402MHz ~ 2480MHz Channel Number : 79 channels for Bluetooth V5.0(DSS) 40 channels for Bluetooth V5.0 (DTS) Channel Spacing : 1MHz for Bluetooth V5.0 (DSS) 2MHz for Bluetooth V5.0 (DTS) Modulation Type : GFSK, π/4-DQPSK for Bluetooth V5.0(DSS) GFSK for Bluetooth V5.0 (DTS) Bluetooth Version : V5.0 Antenna Type : PCB Antenna Antenna Gain : -0.58dBi Exposure category : General population/uncontrolled environment EUT Type : Production Unit Device Type : Portable Device 2. Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · Page 2 of 4 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices Page 3 of 4 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity 4. Conducted Power Results <BT> Mode Channel Frequency (MHz) Peak Conducte…

Text truncated - open the document above for the full version.

Page 1 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Appendix B RF Test Data for BLE (Conducted Measurement) Product Name: Wireless Headphone Test Model: FB-8S Environmental Conditions Temperature: 23.8 C Relative Humidity: 52.1% ATM Pressure: 100.0 kPa Test Engineer: Nick Peng Supervised by: Li huan Page 2 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity B.1 -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT BLE 1M 2402 Ant1 0.694 >=0.5 Pass NVNT BLE 1M 2440 Ant1 0.71 >=0.5 Pass NVNT BLE 1M 2480 Ant1 0.709 >=0.5 Pass Page 3 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs -6dB Bandwidth NVNT BLE 1M 2402MHz Ant1 -6dB Bandwidth NVNT BLE 1M 2440MHz Ant1 Page 4 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity -6dB Bandwidth NVNT BLE 1M 2480MHz Ant1 Page 5 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity B.2 Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Duty Factor (dB) Total Power (dBm) Limit (dBm) Verdict NVNT BLE 1M 2402 Ant1 0.28 0 0.28 30 Pass NVNT BLE 1M 2440 Ant1 0.41 0 0.41 30 Pass NVNT BLE 1M 2480 Ant1 0.16 0 0.16 30 Pass Page 6 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs Power NVNT BLE 1M 2402MHz Ant1 Power NVNT BLE 1M 2440MHz Ant1 Page 7 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Power NVNT BLE 1M 2480MHz Ant1 Page 8 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity B.3 Maximum Power Spectral Density Level Condition Mode Frequency (MHz) Antenna Conducted PSD (dBm/3kHz) Duty Factor (dB) Total PSD (dBm/3kHz) Limit (dBm/3kHz) Verdict NVNT BLE 1M 2402 Ant1 -14.85 0 -14.85 8 Pass NVNT BLE 1M 2440 Ant1 -14.8 0 -14.8 8 Pass NVNT BLE 1M 2480 Ant1 -14.98 0 -14.98 8 Pass Page 9 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs PSD NVNT BLE 1M 2402MHz Ant1 PSD NVNT BLE 1M 2440MHz Ant1 Page 10 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity PSD NVNT BLE 1M 2480MHz Ant1 Page 11 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity B.4 Band Edge Condition Mode Frequency (MHz) Antenna Max Value (dBc) Limit (dBc) Verdict NVNT BLE 1M 2402 Ant1 -45.42 -20 Pass NVNT BLE 1M 2480 Ant1 -50.18 -20 Pass Page 12 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Graphs Band Edge NVNT BLE 1M 2402MHz Ant1 Ref Band Edge NVNT BLE 1M 2402MHz Ant1 Emission Page 13 of 23 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg …

Text truncated - open the document above for the full version.

Page 1 of 34 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT For COLMAN INC Wireless Headphone Test Model: FB-8S Additional Model No.: Please Refer to Page 6 Prepared for : COLMAN INC Address : CAMBRIDGE HOUSE 27 CAMBRIDGE PARK ROAD LONDON UNITED KINGDOM Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : July 05, 2022 Number of tested samples : 2 Sample No. : A070522027-1, A070522027-2 Serial number : Prototype Date of Test : July 05, 2022 ~ July 11, 2022 Date of Report : July 12, 2022 Page 2 of 34 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15 C(15.247) Report Reference No. ................. : LCSA070522027EB Date of Issue .................................. : July 12, 2022 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address .......................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure .......... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : COLMAN INC Address .......................................... : CAMBRIDGE HOUSE 27 CAMBRIDGE PARK ROAD LONDON UNITED KINGDOM Test Specification Standard ......................................... : FCC CFR 47 PART 15 C(15.247) Test Report Form No.................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. EUT Description. .......................... : Wireless Headphone Trade Mark ..................................... : CANDI LONDON Test Model ...................................... : FB-8S Ratings ........................................... : Input: DC 5V, 150mA DC 3.7V by Rechargeable Li-ion Battery, 200mAh Result ............................................ : Positive Compiled by: Supervised by: Approved by: Li Huan/ Administrator Jin Wang/ Technique principal Gavin Liang/ Manager Page 3 of 34 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC -- TEST REPORT Test Model............................... : FB-8S EUT......................................... : Wireless Headphone Applicant............................... : COLMAN INC Address.................................. : CAMBRIDGE HOUSE 27 CAMBRIDGE PARK ROAD LONDON UNITED KINGDOM Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Shantou Storm Electronic Technology Co. Ltd Address................................... : No.2, Lane 4, xianbo Jiangjunyang, Gurao Town, Chaoyang District, Shantou, Guangdong 515159, China Telephone............................... : / Fax.......................................... : / Factory................................... : Shantou Storm Electronic Technology Co. Ltd Address................................... : No.2, Lane 4, xianbo Jiangjunyang, Gurao Town, Chaoyang District, Shantou, Guangdong 515159, China Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCSA070522027EB July 12, 2022 Date of issue Page 4 of 34 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Revision History Report Version Issue Date Revision Content Revised By 000 July 12, 2022 Initial Issue --- Page 5 of 34 FCC ID: 2A7TE-FB-8S Report No.: LCSA070522027EB Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity TABLE OF CONTENTS 1. GENERAL INFORMATION ..................…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Setup Photos of the EUT Test Setup Photo(s) of Radiated Emissions Measurement Fig. 1 Fig. 2 Page 2 of 2 FCC ID: 2A7TE-FB-8S Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Setup Photo(s) of Conducted Emissions Measurement Fig. 3