2A82F-STTH785043RADIO CONTROL TOYS

FCC Compliance Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The following terms are used throughout the product literature to indicate various levels of potential harm when operating this produc t: NOTICE: Procedures, which if not be properly followed, will create a possibility of physical property damage AND or possibility of injury. WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by SHAANTOU CHENGHHAI TENGHUI PLASTIC TOYS FACTORY. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury. AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT ATOY. Safety Precautions and Warnings As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or prope门yof others. Always keep a safe distance in all directions around your model to avoid collisions or injury.This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control. Always operate your vehicle in open space away from full-size vehicles, traffic, people and animals. Always carefully follow the directions and warnings for this and any optional suppo时equipment(chargers, rechargeable battery packs, etc.). Always keep all chemicals.small parts and anything electrical out of the reach of children. Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics. Never place any p。而onof the vehicle in your mouth as it could cause serious injury or even death. Never operate your vehicle with low trasmitter batteries. Always keep your vehicle in sight and under control. Always use fully charged batteries. Always keep transmitter powered on while your vehicle is power on. Always remove batteries before disassembly. Always keep moving pa时sclean. Always keep pa同sd叩． Always let pa同Scool after use before touching. Always remove battereis after use. Never operate your vehicle with damaged wiring. Box Contents 〉 2/4 How-to-start Guide Slide the switch Solid:Batte「yis in good condition(Above 4.3V) Flashin ! f Battery 1s at low voltage Replace batteries (below 4.3V) 1. Install 2 x AA batteries (not included) into the transmitter, power on the transmitter. 2. Move the power switch to “ON ” position on the bottom of the ca『． 合 。 念、r立7 3. To slowly drive forward, pull the throttle trigger slightly. 4. Rotate the wheel counter-clockwise to turn left. Rotate Adjust the speed by pulling the trigger. Push the triggerthe wheel clockwise to turn right. to brake/reverse. Release the trigger to keep your vehicle still. Running Tips: 1. Run your vehicle on a flat su「face,and keep your vehicle in sight. 2. Always release the th「ottletrigger right away following a crash to prevent further damages. 3. Do not run your vehicle in an area with people or property nearby. 4. When you finish, always turn off your transmitter AFTER your vehicle power. 5. Always keep the battery unplug when you are not attempt to run the vehicle. Switch to drifting tires 1. Use a Philips screw driver to I。osen the screw from the rims by counter-cl。ckwisedirection. 2. Remove all the 4 rims with speed tires from the chassis. 3. Install the rims with drifting tires. 4. Tighten the rims to the chassis by clockwise direction. 4/4 Product Description： RADIO CONTROL TOYS NO.EXA785043

SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Date: 2022-10-20 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2A82F-STTH785043 To whom it may concern: We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY This authorization is valid until further written notice from the applicant. Print Name: YAORONG CHENG Title: SALESMAN Signature: On behalf of Company: SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Telephone: 0754-85733320 E-mail: [email protected]

SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: 2A82F-STTH785043 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY（Remark：如下资料需要短期保密请选择天数0，45,90或者180天，短期保密期间产品不能在美国市场上售卖。 Additionally, the applicant requests the following documents be held confidential until the device is marketed or 0 days from the grant date, whichever is less. If the device is marketed within 0 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Delete any document that is NOT included in your application External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: YAORONG CEHNG Title: SALESMAN Signature: On behalf of Company: SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Telephone: 0754-85733320 E-mail: [email protected]

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Address KUNMEI NEW INDUSTRIAL PARK,FENGXIANG STREET,CHENGHAI SHANTOU, 515800 CHINA Grantee Code 2A82F FCC ID 2A82F-STTH785043 Authorized Contact Name YAORONG CEHNG Contact Email [email protected] Contact Phone 0754-85733320 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2022-10-20 Print Name: YAORONG CHENG Title: SALESMAN *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 1 of 4 Appendix External Photos for FYCR2210000403AT FCC ID: 2A82F-STTH785043 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 2 of 4 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A02 Rev.A/0 Page: 4 of 4

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 1 of 4 Appendix Internal Photos for FYCR2210000403AT FCC ID: 2A82F-STTH785043 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 2 of 4 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 3 of 4 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A03 Rev.A/0 Page: 4 of 4 - End of the Appendix -

Antenna specification table: 1: Antenna is a whip antenna: Whip antenna uses copper core RF wire, transmitting antenna size: 0.8 * 70mm, whip antenna needs to be vertically welded to the PCB plate, Shenzhen Lixinhui Electronics Co., Ltd Yonghang Electronics Min Zhou 0.8*70mm Integral antenna There is no requirement for PCB plane size, but the height requirement is required (greater than 30mm). This antenna communication is better communication than the other four PFIA antennas The distance is further, about 20% higher. 2: Technical data sheet: Remark:Only radiated measurements are used to show compliance with FCC limits for fundamental and spurious emissions.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221000040302 Page: 1 of 43 Winkey Wang EMC Technical Manager TEST REPORT Application No.: FYCR2210000403AT Applicant: SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Address of Applicant: KUNMEI NEW INDUSTRIAL PARK, FENGXIANG STREET, CHENGHAI SHANTOU, 515800 CHINA Manufacturer: SHANTOU CHENGHAI TENGHUI PLASTIC TOYS FACTORY Address of Manufacturer: KUNMEI NEW INDUSTRIAL PARK, FENGXIANG STREET, CHENGHAI SHANTOU, 515800 CHINA Equipment Under Test (EUT): EUT Name: RADIO CONTROL TOYS Model No.: EXA785043, EXA785011, EXA785012, EXA785013, EXA785014, EXA785015, EXA785016, EXA785017, EXA785018, EXA785019, EXA7850110, EXA7850111, EXA7850112, EXA785021, EXA785022, EXA785023, EXA785031, EXA785032, EXA785033, EXA785041, EXA785042, EXA785044, EXA785045, EXA785046, EXA785047, EXA785048, EXA785049, EXA7850410, EXA7850411, EXA7850412, EXA78505, EXA78506, EXA78507, EXA78508, EXA78509, EXA78510, EXA78511, EXA78512, EXA78513, EXA78514, EXA78515, 535-01/200, 595-01/200, 636-01/200, 898-01/200, 868-01/200, 555-01/200, 080-01/200, 081-01/200, 082-01/200, 083-01/200, 381-382, 383-01/200, 353-01/200, 888-01/200, 999-01/200, 686-01/200, 565-01/200, 575-01/200, 585-01/200, 282-01/200, 636-01/200, 252-01/100, 253-01/100, 254-01/100, 255-01/100, 256-01/100, 257-01/100, 258-01/100, 232-01/200, 323-01/200, 454-01/200, 262-01/200, 262-101ABCD, 262-121ABCD, 262-122ABCD, 262-B121 ♣ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. FCC ID: 2A82F-STTH785043 Standard(s) : 47 CFR Part 15, Subpart C 15.249 Date of Receipt: 2022-10-14 Date of Test: 2022-10-19 to 2022-11-10 Date of Issue: 2022-11-11 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221000040302 Page: 2 of 43 Revision Record Version Chapter Date Modifier Remark 01 2022-11-11 Original Authorized for issue by: Tree Zhan/Project Engineer Winkey Wang/Reviewer Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221000040302 Page: 3 of 43 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.249 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.249 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.215 Pass Field Strength of the Fundamental Signal (15.249(a)) ANSI C63.10 (2013) Section 6.5&6.6 47 CFR Part 15, Subpart C 15.249(a) Pass Restricted Band Around Fundamental Frequency ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.249(d) & 15.209 Pass Radiated Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4&6.5 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass Radiated Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.209 & 15.249 (a),(d) Pass Declaration of EUT Family Grouping: Model No.: EXA785043, EXA785011, EXA785012, EXA785013, EXA785014, EXA785015, EXA785016, EXA785017, EXA785018, EXA785019, EXA7850110, EXA7850111, EXA7850112, EXA785021, EXA785022, EXA785023, EXA785031, EXA785032, EXA785033, EXA785041, EXA785042, EXA785044, EXA785045, EXA785046, EXA785047, EXA785048, EXA785049, EXA7850410, EXA7850411, EXA7850412, EXA78505, EXA78506, EXA78507, EXA78508, EXA78509, EXA78510, EXA78511, EXA78512, EXA78513, EXA78514, EXA78515, 535-01/200, 595-01/200, 636- 01/200, 898-01/200, 868-01/200, 555-01/200, 080-01/200, 081-01/200, 082-01/200, 083-01/200, 381- 382, 383-01/200, 353-01/200, 888-01/200, 999-01/200, 686-01/200, 565-01/200, 575-01/200, 585- 01/200, 282-01/200, 636-01/200, 252-01/100, 253-01/100, 254-01/100, 255-01/100, 256-01/100, 257- 01/100, 258-01/100, 232-01/200, 323-01/200, 454-01/200, 262-01/200, 262-101ABCD, 262-121ABCD, 262-122ABCD, 262-B121 Only the model EXA785043 was tested, since according to the declaration from the applicant, the electrical circuit design, PCB layout, components used and internal wiring and functions were identical for the above models, with only difference on color. Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-01 Rev. A/0 Aug01,2022 Report No.: FYCR221000040302 Page: 4 of 43 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 4 4 GENERAL INFORMATION .................................................................................................................. 6 4.1 DETAILS OF E.U.T. ......................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 7 4.4 TEST LOCATION ............................................................................................................................. 8 4.5 TEST FACILITY ............................................................................................................................... 8 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 8 4.7 ABNORMALITIES FROM STANDARD CONDITIONS .…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 1 of 3 Appendix Test Setup Photos for FYCR2210000403AT FCC ID: 2A82F-STTH785043 Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 2 of 3 Test Setup Photo Field Strength of the Fundamental Signal (15.249(a)) Restricted Band Around Fundamental Frequency Compliance Certification Services (Kunshan) Inc. Shenzhen Branch SZCCS-TRF-A04 Rev.A/0 Page: 3 of 3 Radiated Emissions Below 1GHz Radiated Emissions Above 1GHz - End of the Appendix -