2A82RMARK3Arable Mark 3

Arable Mark 3 Quick Start Guide Step 1: Connect your Device to a Charger. Charge until your device’s lightning icon turnswhiteby plugging your charging cord into a (at minimum 10W) USB-C wall charger. The light will begreenwhile charging. Step 2: Ensure the solar panel is attached to the Mark 3. To attach your solar panel first attach the cable from the panel into the cable attached to the Mark 3 until you hear a snap. Insert the connected cables in the solar panel cavity. Next, slide the groove of the panel down the casing of the Mark 3 from the top going down (make sure the cables are not in the way of the groove). There will be a hard click and you will see agreen lightat thelightning icon if it is properly connected and in sufficient sunlight. Ensure that the knob included in packaging is screwed into the side and securing the solar panel in place. Do not proceed until you have successfully attached the solar panel to the Mark 3. For maximum charging, face the solar panel towards the equator. The panel may be faced up to 90 degrees away from the equator if needed. www.arable.com ○ [email protected] ○ 510-992-4095Pg.1 Step 3: Attach antennas Ensure that each antenna is attached to the correct port on the underside of the Mark. Each antenna has a color coded icon that matches the icon on the Mark for Cellular and Bluetooth ports. Step 4: Deploy your Device. Turn the device on to collect data and sync with our backend. Each time you do this you will create a “deployment”. To do this hold the power button for2 seconds. The deployment sequencewill begin from left to right starting with the battery icon. Note: It may take 5 to 10 minutes for lights to stop flashing during the deployment sequence. *See Deployment Outcomes below. www.arable.com ○ [email protected] ○ 510-992-4095Pg.2 Step 5: Attach Bird Spikes Take bird spikes out of the package and attach one by one to the top of the Mark. The 4 longer spikes with the orange rubber ends are to be placed at the 12, 3, 6, and 9 o’clock positions. Step 6: View your data in the Arable web or mobile application Use your login credentials to view data from your Mark 3(s) at app.arable.com *Deployment Outcomes Successful DeploymentOnce the activation process has completed the finished status of each light UI will remain steady for 10 seconds before every light except for the lightning bolt goes out . A successful deployment will display green lights Failed DeploymentThe LEDs will flash Red for 30 seconds if a deployment has failed. Any failure of an individual icon is indicated by a Red LED. Battery too low to connect → Take inside to charge. Sensor Failure → Contact Arable Connectivity to Server → Move location and contact Arable. Bridge sensor connected but no communication → Contact Arable Lightning Charge LEDGreen when receiving power. OrientationYour Mark 3 should be deployed 3-4 feet above the maximum expected height of your crop canopy. The “A” Arable logo should point toward the equator. www.arable.com ○ [email protected] ○ 510-992-4095Pg.3 Sensor Guide Meaning of Sensors (from Left to Right) Battery signal Green → Sufficient power to deploy Red → Battery is too low to connect Internal Sensors Green→ Sensors all are in working condition Red → One or more sensor has failed Connectivity→ Device has received GPS & connectedto the Arable Database. External/Auxiliary Sensors→ Status of additional attachedsensors. Amber→no sensors attached Green → one sensor attached Purple → two or more sensors attached Charge Status (Lightning LED)→ Display of whetherMark is being charged or not by a charger or a solar panel. Actions you can take.Status Check→ Quick tap and release of the Powerbutton. 4 lights flash amber→Undeployed Four (4) Green lights flash→ Deployed Deploy/Undeploy→ 2 second press, hold, and releaseof the Power button. *The Mark 3 must be deployed in outdoor/open-air locations to establish a GPS connection. The connectivity icon will blink for >5 minutes while the Mark tries to establish a connection with a cell tower. Hard Reset→ 15 second hold and release of the Powerbutton. www.arable.com ○ [email protected] ○ 510-992-4095Pg.4 FCC Statement Interference Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimu…

Text truncated - open the document above for the full version.

51 Federal St., San Francisco, CA 94107, USA Date: 2023-02-09 FCC ID: 2A82RMARK3 To the attention of Federal Communications Commission Authorization and Evaluation Division Attestation Statements Attestation Statements Part 2.911(d)(5)(i) Filing Arable Labs Inc. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Attestation Statements Part 2.911(d)(5)(ii) Filing Arable Labs Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely yours, ----------------------------------------------- Ron Butterworth Arable Labs Inc. E-mail [email protected] Phone number (408) 427-2050

51 Federal St., San Francisco, CA 94107, USA U.S. Agent for Service of Process Attestation To the attention of Federal Communications Commission Authorization and Evaluation Division Applicant / Designated U.S Agent Company Name: Arable Labs Inc. Grantee Code: 2A82R Contact Name: Ron Butterworth Street Address: 51 Federal St., San Francisco City/Province/Zip: CA 94107 Telephone No: (408) 427-2050 Email: [email protected] This letter is to confirm that the Applicant has designated itself as the U.S Agent for service of process as required by §2.911(d)(7). The Applicant further acknowledges acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant / U.S. Agent Signature: [email protected] Date: 2023-02-13 Signed by [email protected]: ___________________________ Ron Butterworth

51 Federal St., San Francisco, CA 94107, USA Date: 2022-11-15 FCC ID: 2A82RMARK3 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description Part list Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ----------------------------------- Ron Butterworth Arable Labs Inc. E-mail [email protected] Phone number (408) 427-2050

51 Federal St., San Francisco, CA 94107, USA Date: 2022-11-15 FCC ID: 2A82RMARK3 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ----------------------------------- Ron Butterworth Arable Labs Inc. E-mail [email protected] Phone number (408) 427-2050

51 Federal St., San Francisco, CA 94107, USA Date: 2022-11-15 FCC ID: 2A82RMARK3 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern: Arable Labs Inc. hereby authorizes Trista Tsai / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (“BV CPS Taoyuan”), to act on its behalf in all matters relating to the Federal Communication Commission (“FCC”) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Trista Tsai / Specialist of BV CPS Taoyuan on Arable Labs Inc.’s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely yours, ----------------------------------------------- Ron Butterworth Arable Labs Inc. E-mail [email protected] Phone number (408) 427-2050

Reference No.: BCKS-WTW-P22090987_EXT 1 of 8 CONSTRUCTION PHOTOS OF EUT Reference No.: BCKS-WTW-P22090987_EXT 2 of 8 Reference No.: BCKS-WTW-P22090987_EXT 3 of 8 Reference No.: BCKS-WTW-P22090987_EXT 4 of 8 Reference No.: BCKS-WTW-P22090987_EXT 5 of 8 Reference No.: BCKS-WTW-P22090987_EXT 6 of 8 Reference No.: BCKS-WTW-P22090987_EXT 7 of 8 Reference No.: BCKS-WTW-P22090987_EXT 8 of 8

Bottom of EuT Label & Label location

Reference No.: BCKS-WTW-P22090987_INT 1 of 21 CONSTRUCTION PHOTOS OF EUT Reference No.: BCKS-WTW-P22090987_INT 2 of 21 Reference No.: BCKS-WTW-P22090987_INT 3 of 21 Reference No.: BCKS-WTW-P22090987_INT 4 of 21 Reference No.: BCKS-WTW-P22090987_INT 5 of 21 Reference No.: BCKS-WTW-P22090987_INT 6 of 21 Reference No.: BCKS-WTW-P22090987_INT 7 of 21 Reference No.: BCKS-WTW-P22090987_INT 8 of 21 Reference No.: BCKS-WTW-P22090987_INT 9 of 21 Reference No.: BCKS-WTW-P22090987_INT 10 of 21 Reference No.: BCKS-WTW-P22090987_INT 11 of 21 Reference No.: BCKS-WTW-P22090987_INT 12 of 21 Reference No.: BCKS-WTW-P22090987_INT 13 of 21 Reference No.: BCKS-WTW-P22090987_INT 14 of 21 Reference No.: BCKS-WTW-P22090987_INT 15 of 21 Reference No.: BCKS-WTW-P22090987_INT 16 of 21 Reference No.: BCKS-WTW-P22090987_INT 17 of 21 Reference No.: BCKS-WTW-P22090987_INT 18 of 21 Reference No.: BCKS-WTW-P22090987_INT 19 of 21 WWAN Antenna Reference No.: BCKS-WTW-P22090987_INT 20 of 21 BT Antenna Reference No.: BCKS-WTW-P22090987_INT 21 of 21

Report No.: MFBCKS-WTW-P22090987 Page No. 1 / 7 Report Format Version: 6.1.1 RF Exposure Report Report No.: MFBCKS-WTW-P22090987 FCC ID: 2A82RMARK3 Test Model: Mark 3 Received Date: Oct. 17, 2022 Date of Evaluation: Nov. 22, 2022 Issued Date: Dec. 12, 2022 Applicant: Arable Labs Inc. Address: 51 Federal St., San Francisco, CA 94107, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: MFBCKS-WTW-P22090987 Page No. 2 / 7 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: MFBCKS-WTW-P22090987 Page No. 3 / 7 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued MFBCKS-WTW-P22090987 Original Release Dec. 12, 2022 Report No.: MFBCKS-WTW-P22090987 Page No. 4 / 7 Report Format Version: 6.1.1 1 Certificate of Conformity Product: Arable Mark 3 Brand: Arable Labs Test Model: Mark 3 Sample Status: Engineering Sample Applicant: Arable Labs Inc. Date of Evaluation: Nov. 22, 2022 FCC Rule Part: FCC Part 2 (Section 2.1091) Standards: KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Dec. 12, 2022 Vera Huang / Specialist Approved by : , Date: Dec. 12, 2022 Jeremy Lin / Project Engineer Report No.: MFBCKS-WTW-P22090987 Page No. 5 / 7 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 f = Frequency in MHz; *Plane-wave equivalent power density 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: MFBCKS-WTW-P22090987 Page No. 6 / 7 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Band Max ERP Power (dBm) Max EIRP Power (dBm) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) GPRS 850 31.17 33.32 20 0.427 0.55 GPRS 1900 - 32.12 20 0.324 1.00 eMTC LTE Band 2 - 26.42 20 0.087 1.00 LTE Band 4 - 25.79 20 0.075 1.00 LTE Band 5 22.13 24.28 20 0.053 0.55 LTE Band 12 22.23 24.38 20 0.055 0.46 LTE Band 13 22.13 24.28 20 0.053 0.52 LTE Band 25 - 25.97 20 0.079 1.00 LTE Band 26 22.39 24.54 20 0.057 0.54 LTE Band 66 - 25.…

Text truncated - open the document above for the full version.

Form No.:705-N0016-06,002 X1Revision Site 3：Factory Name Mark ADDRESS Site 1：Factory Name Site 2：Factory Name MFGTEL 08.21030.003 103DG00000130 WNC P/N Brand Supplier P/N SupplierGTT Parts Specification Cover Wistron Neweb CorporationCustomer approvalreviewerprepared supplierYW Temperature Radome colorWhite Humidity Weight 60gw Radome materialASA Dimensions 25 x 180mm Environmental & Mechanical Characteristics -40°C to 70 °C 95% @ 55 °C Frequency Range 2400MHz~2500MHz HPBW-Vertical Efficiency VSWR 2.0 Max.:1 Peak Gain 50 Ohms Electrical Specification Polarization 5150MHz - 5850MHz5925MHz - 7125MHz 360∘ HPBW-Horizontal 90 ∘ Impedance Linear, Vertical N plug Connector 4 dBi Max. 7 dBi Max. 7.5 dBi Max. 65% Min. 70% Min. 64% Min. 25.0±0.3 180±0.6mm 5/8-24 UNEF Color: White UNLESS OTHERWISE SPECIFIED DO NOT SCALE DRAWING ANGLES : ±2° X.X ±0.3 ±0.15 X.XX TOLERANCE : ITEM NO. SCALE A3 SIZE TITLE UNITPART NO. DATE PAGE OF REV. RoHS THIRD ANGLE PROJECTION 榮昌科技股份有限公司 GRAND-TEK TECHNOLOGY CO., LTD. REACH 1 1 Type No. APPROVED BY CHECKED BY BY DRAWN Designed BY Gene Eric Mark YW - mm 1:1 Antenna,WiFi 6E,Dual Band 08.21030.003 G00140 X1 2022-08-01 103DG00000130 40.0 SAFETY DATA SHEET according to Singapore Standard SS 586 - Part 3 - 2008 Luran® S AMS Natural Material number LUR121 Revision date:4/12/2020 Version:7.1 Language:en-SG Date of print:11/10/2021 Page:1 of 8 1. Identification of the substance/mixture and of the company/undertaking Product identifier Trade name: Luran® S AMS Natural This safety data sheet pertains to the following products: Luran® S 778T Q42 NR Luran® S 778T Q443 NR Luran® S 778T Q495 NR Luran® S 778T Q496 NR Luran® S 778T UV NR Luran® S 778T UV SPL Relevant identified uses of the substance or mixture and uses advised against General use: Polymer Basic material for chemical industry processing Details of the supplier of the safety data sheet Company name: INEOS Styrolution APAC Pte Ltd. Street/POB-No.: 111 Somerset Road Postal Code, city: #08-01/02 TripleOne Somerset, SG Singapore 238164 WWW: www.styrolution.com E-mail: [email protected] Telephone: +65 6933 8350 Telefax: +65 6933 8355 Department responsible for information: Infopoint, Telephone: + 65 (0) 6933 - 8372 E-mail: [email protected] Emergency telephone number Telephone: +86 512 8090 3042 (Country); + 65 3158 1074 (regional) 2. Hazards identification Classification of the substance or mixture GHS classification This mixture is classified as not hazardous. Label elements Hazard statements: not applicable Precautionary statements: not applicable printed by INEOS Styrolution APAC Pte Ltd.with Qualisys SUMDAT SAFETY DATA SHEET according to Singapore Standard SS 586 - Part 3 - 2008 Luran® S AMS Natural Material number LUR121 Revision date:4/12/2020 Version:7.1 Language:en-SG Date of print:11/10/2021 Page:2 of 8 Other hazards Dust: Can cause skin, eye and respiratory tract irritation. May cause allergic reactions in already sensitized persons. The melted product can cause severe burns. Swallowing may cause gastrointestinal irritation and pain of guts. 3. Composition/information on ingredients Mixtures Chemical characterisation: Polymer mixture: CAS No. 25747-74-4 alpha-methylstyrene acrylonitrile copolymer CAS No. 26299-47-8 Butyl acrylate-styrene-acrylonitrile copolymer Hazardous ingredients: CAS No.DesignationContentClassification CAS 52829-07-9Bis(2,2,6,6-Tetramethyl-4- piperidyl)sebacate < 1 %Eye Dam. 1. Aquatic Acute 1 (M-factor = 1). Aquatic Chronic 2. Additional information: The substances are encapsulated in a polymer and are therefore not bioavailable. 4. First aid measures In case of inhalation: Provide fresh air. Put victim at rest and keep warm. seek medical attention Following skin contact: The melted product can cause severe burns. Do not remove the product from the skin without medical assistance. After contact with molten product, cool skin area rapidly with cold water. Consult physician. After eye contact: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Consult an eye specialist in the event of irritation. After swallowing: Rinse mouth with water. Drink one or two glasses of water. Never give an unconscious person anything through the mouth. seek medical attention Most important symptoms and effects, both acute and delayed Dust: Skin irritation, eye irritations and redness Indication of any immediate medical attention and special treatment needed Treat symptomatically. 5. Firefighting measures Extinguishing media Suitable extinguishing media: Water spray jet, foam, extinguishing powder, carbon dioxide. Extinguishing media which must not be used for safety reasons: Full water jet printed by INEOS Styrolution APAC Pte Ltd.with Qualisys SUMDAT SAFETY DATA SHEET according to Singapore Standard SS 586 - Part 3 - 2008 Luran® S AMS Natural Material number LUR121 Revision date:4/12/2020 Version:7.1 Language:en-SG Date of print:11/10/2021 Page:3 of 8 Special hazards arising from the substance or mixture In case of fire may be liberated: Smoke, hydrogen cyanide, carbon monoxide and carbon dioxide (CO2). In case of dust formation (Fine dust): May form explosible dust-air mixture if dispersed. Advice for firefighters Special protective equipment for firefighters: Wear a self-contained breathing apparatus and chemical protective clothing. Additional information: Do not allow fire water to penetrate into surface or ground water. Fire residuals and contaminated extinguishing water must be disposed of in accordance with the regulations of the local authorities. 6. Accidental release measures Personal precautions, protective equipment and emergency procedures Provide adequate ventilation. Wear personal protection equipment. Do not breathe dust. Environmental precautions Do not allow to penetrate into soil, waterbodies or drains. Methods and material for containment and cleaning up Avoid generation of dust. Remove all sources of ignition.…

Text truncated - open the document above for the full version.

Report No.: RFBCKS-WTW-P22090987-5 Page No. 1 / 27 Report Format Version: 6.1.1 FCC Test Report (Co-located) Report No.: RFBCKS-WTW-P22090987-5 FCC ID: 2A82RMARK3 Test Model: Mark 3 Received Date: Oct. 17, 2022 Test Date: Nov. 10, 2022 Issued Date: Dec. 12, 2022 Applicant: Arable Labs Inc. Address: 51 Federal St., San Francisco, CA 94107, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBCKS-WTW-P22090987-5 Page No. 2 / 27 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes ..................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................. 10 3.3 Duty Cycle of Test Signal ..................................................................................................................... 11 3.4 Description of Support Units ............................................................................................................... 12 3.4.1 Configuration of System under Test ......................................................................................... 12 3.5 General Description of Applied Standards .......................................................................................... 13 4 Test Types and Results ............................................................................................................................ 14 4.1 Radiated Emission and Bandedge Measurement .............................................................................. 14 4.1.1 Limits of Radiated Emission and Bandedge Measurement ..................................................... 14 4.1.2 Test Instruments ....................................................................................................................... 15 4.1.3 Test Procedures ........................................................................................................................ 16 4.1.4 Deviation from Test Standard ................................................................................................... 17 4.1.5 Test Setup ................................................................................................................................. 18 4.1.6 EUT Operating Conditions ........................................................................................................ 19 4.1.7 Test Results .............................................................................................................................. 20 5 Pictures of Test Arrangements................................................................................................................ 26 Appendix – Information of the Testing Laboratories ................................................................................. 27 Report No.: RFBCKS-WTW-P22090987-5 Page No. 3 / 27 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued RFBCKS-WT…

Text truncated - open the document above for the full version.

Report No.: RFBCKS-WTW-P22090987 Page No. 1 / 40 Report Format Version: 7.1.0 TEST REP…

Text truncated - open the document above for the full version.