2A88ZEFACFEV Flex-AC LE

EV FLEX-AC LE OWNER'S MANUAL Version 1.1 Product Specifications .................................................... 14 Important Safety Instructions .......................................... 1 Box Contents ................................................................. 3 Installation Guide .......................................................... 4 Operation of Control Panel ........................................... 6 App Instrucion .............................................................. 7 Troubleshooting ............................................................12 Charging Your Vehicle .................................................. 11 Limited Warranty Information ......................................... 16 Warranty Card .............................................................. 18 CONTENT 1 INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ CONSERVER CES INSTRUCTIONS.INSTRUCTIONS AYANT TRAIT À UN RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE. ATTENTION Pour réduire le risque de choc électrique, brancher sur une prise correctement mise à la terre. ATTENTION Risque de choc électrique. Ne pas retirer le couvercle ni essayer d’ouvrir le boîtier.Aucune pièce interne réparable par l’utilisateur. Confier tout travail d’entretien ou de réparation à un technicien qualifié. AVERTISSEMENT Caractéristique de réarmement automatique incluse. VERTISSEMENT Pour réduire le risque de choc électrique ou d’incendie, ne pas utiliser de rallonge avec cet appareil. AVERTISSEMENT Ce dispositif est destiné au chargement des véhicules ne nécessitant pas de ventilation au cours du chargement. Risque de choc électrique. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Read this entire document and follow all warnings and instructions before installing and using the EV Flex-AC Charger. Install and use this product only within the specified operating parameters as instructed in the manual. Failure to comply can lead to property damage, injury, or death, and will void the Limited Warranty. Warning: The EV Flex-AC Charger is not user-serviceable, do not attempt to open, disassemble, repair, service, or modify the product. Please contact Customer Support if assistance is needed, refer to page 12 for contact information. Warning: Always plug the EV Flex-AC Charger directly into the outlet with the supplied power adapter. Do not use extension cords, multi-outlet adapter, multi-plug, conversion plug or power strip to plug in the product. Warning: This device is intended only for charging vehicles not requiring ventilation during charging. Warning: Do not use the EV Flex-AC Charger if any component appears to be broken, cracked, frayed, or show any indication of damage or defect. Please contact the Customer Support immediately, refer to page 12 for contact information. Warning: Do not use private power generators as a power source for the EV Flex-AC Charger to charge vehicles. Warning: Never disconnect the EV Flex-AC Charger’s power adapter from the power outlet while the vehicle is still charging. Always stop the charging process, disconnect he charging handle from the vehicle, then disconnect the power adapter from the outlet. Warning: Always inspect the outlet before plugging the EV Flex-AC Charger in and ensure all prongs of the power adapter are fully inserted into the outlet. The power adapter may overheat and cause damage or injury if it is not inserted properly. Do not plug the product into an outlet that appears damaged, loose, or worn. Warning: Do not expose the EV Flex-AC Charger to any flammable, explosive, or combustible materials/vapors. Warning: Do not install or use the EV Flex-AC Charger near flammable, explosive, or combustible materials/vapors, or if exposed to severe rain, snow, thunderstorm, or any other inclement weather. IMPORTANT SAFETY INSTRUCTIONS - WARNINGS 2 Warning: If possible, avoid installing the EV Flex-AC Charger in direct sunlight. Warning: Handle all components of the EV Flex-AC Charger with care. Do not drop, drag, batter, twist, tangle, step on or exert strong force/impact on the EV Flex-AC Charger. Warning: Do not allow moisture, water, or debris to enter the openings of the EV Flex-AC Charger, especially the outlet, connecter or charging handle port. Warning: Do not plug the EV Flex-AC Charger into an outlet if it is submerged in water or covered in snow. If the product is already plugged in, turn off the breaker before unplugging the power adapter. Warning: Do not touch the connecters of the EV Flex-AC Charger power adapter or control box with your fingers or other objects, including wire, tools, or needles. Do not fold any component of the product by force or damage it with sharp objects. Do not insert foreign objects into the product. Warning: Install and mount the EV Flex-AC Charger in a position so it does not hang from the power outlet. The power outlet and adapter are not designed to support the weight of the EV Flex-AC Charger. Warning: Hang the EV Flex-AC Charger’s charging cable on the supplied hook in a location that prevents obstruction of pedestrians, pets, vehicles, or other objects. Position it in such a way to prevent damaging or stressing the components. Do not subject the charging cable to excessive forces or impact, such as closing a garage door or driving over it. Warning: Operation of the EV Flex-AC Charger may affect the functionality of medical or implantable electronic devices, such as implantable cardiac pacemakers or implantable cardioverter defibrillators. Prior to using the product, consult with the electronic device manufacturer regarding potential effects that charging may have on such electronic devices. Warning: Take care in cleaning the EV Flex-AC Charger. It is recommended to unplug the EV Flex-AC Charg…

Text truncated - open the document above for the full version.

Xinyi Electric Storage (Shenzhen) Co. Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2A88ZEFACF Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram, Schematics, Operational Description, Block Diagram Operation Description schematic diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Jie Xia Xinyi Electric Storage (Shenzhen) Co. Ltd

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers are identical in circuitry and electrical, mechanical and physical construction; the only differences are the model name and EFAC40FA11with connector, EFAC32FA11with connector, EFAC40FA12 without connector, EFAC32FA12 without connector for trading purpose. Production name Trade name Model no. EV Flex-AC LE PION POWER / XES EFAC40FA11、EFAC40FA12、EFAC32FA11、 EFAC32FA12 Confirmed by Xinyi Electric Storage (Shenzhen) Co. Ltd Jie Xia Xinyi Electric Storage (Shenzhen) Co., Ltd Date: 2022-11-7

Xinyi Electric Storage (Shenzhen) Co. Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2022-11-07 SUBJECT: FCC Application for FCC ID: 2A88ZEFACF To Whom It May Concern: We, the undersigned, hereby authorize Lisa Wang at EMTEK (SHENZHEN) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK (SHENZHEN) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Jie Xia Xinyi Electric Storage (Shenzhen) Co. Ltd

Page 1 of 5 EUT INTERNAL PHOTOGRAPHS Page 2 of 5 Page 3 of 5 Page 4 of 5 Page 5 of 5 ----------------The end----------------

EUT EXTERNAL PHOTOGRAPHS Antenna ----------------The end----------------

Report No.ENS2209270085W00101R Page 1 of 34 Ver.1.0 TEST REPORT Product Name ： EV Flex-AC LE Model Number ： EFAC40FA11、EFAC40FA12、 EFAC32FA11、EFAC32FA12 FCC ID 2A88ZEFACF Prepared for : Xinyi Electric Storage (Shenzhen) Co., Ltd Address : Room 501,602,606,608,610, Building A5, Tianrui Industrial Park, No. 35, Fuyuan 1st Road, Fuhai, Bao ‘an, Shenzhen Prepared by : EMTEK (SHENZHEN) CO., LTD. Address : Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number : ENS2209270085W00101R Date(s) of Tests : September 28,2022 to October 31, 2022 Date of issue : November 15, 2022 $二维码$ Report No.ENS2209270085W00101R Page 2 of 34 Ver.1.0 TABLE OF CONTENT Test Report Description Page 1. SUMMARY OF TEST RESULTS .............................................................................................................................. 5 2. GENERAL INFORMATION ...................................................................................................................................... 6 2.1. Description of Device (EUT) .............................................................................................................................. 6 2.2. Input / Output Ports ............................................................................................................................................ 7 2.3. Independent Operation Modes .......................................................................................................................... 7 2.4. Test Manner ....................................................................................................................................................... 7 2.5. Description of Test Facility ................................................................................................................................. 8 2.6. Test Software ..................................................................................................................................................... 8 2.7. Measurement Uncertainty .................................................................................................................................. 8 3. MEASURING DEVICE AND TEST EQUIPMENT .................................................................................................... 9 3.1. For Power Line Conducted Emission Measurement ......................................................................................... 9 3.2. For Radiated Emission Measurement ............................................................................................................... 9 4. POWER LINE CONDUCTED EMISSION MEASUREMENT ................................................................................. 10 4.1. Block Diagram of Test Setup ............................................................................................................................ 10 4.2. Limits ................................................................................................................................................................ 10 4.3. Test Procedure ................................................................................................................................................. 10 4.4. Measuring Results ........................................................................................................................................... 11 5. RADIATED EMISSION MEASUREMENT (UP TO 1GHz) ..................................................................................... 14 5.1. Block Diagram of Test Setup ............................................................................................................................ 14 5.2. Radiated Limit .................................................................................................................................................. 14 5.3. Test Procedure ................................................................................................................................................. 14 5.4. Measuring Results ........................................................................................................................................... 15 6. RADIATED EMISSION MEASUREMENT (ABOVE 1GHz) ................................................................................... 18 6.1. Block Diagram of Test Setup ............................................................................................................................ 18 6.2. Radiated Limit .................................................................................................................................................. 18 6.3. Test Procedure ................................................................................................................................................. 18 6.4. Measuring Results ........................................................................................................................................... 19 7. PHOTOGRAPHS .................................................................................................................................................... 22 7.1. Photos of Conducted Emission Measurement................................................................................................. 22 7.2. Photos of Radiation Emission Measurement ................................................................................................... 23 APPENDIX A: Warning Labels APPENDIX B: Warning Statement APPENDIX C: Photos of EUT Report No.ENS2209270085W00101R Page 3 of 34 Ver.1.0 TEST REPORT DESCRIPTION Applicant : Xinyi Electric Storage (Shenzhen) Co., Ltd Address : Room 501,602,606,608,610, Building A5, Tianrui Industrial Park, No. 35, Fuyuan 1st Road, Fuhai, Bao ‘an, Shenzhen Manufacturer : Xinyi Electric Storage (Shenzhen) Co., Ltd Address : Room 501,602,606,608,610, Building A5, Tianrui Industria…

Text truncated - open the document above for the full version.

Photos of Conducted Emissions from the AC Mains Power Ports 1.1. Photos of Radiation Emission Measurement ---The End---