2A8JO-FLXK315Remote control code keypad radio transmitter

KSWKP Wireless Keypad #60575312 1-800-378-1001 for Technical Support • Install Wireless Keypad within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5m) and away from ALL moving parts of garage door. • Always keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls. • Activate garage door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of moving garage door. WARNING TO PREVENT SERIOUS INJURY OR DEATH FROM A MOVING RESIDENTIAL GARAGE DOOR: This product can expose you to chemicals which are known in the State of California information, go to www.P65warnings.ca.gov. DESCRIPTION This 315MHz wireless keypad is designed for use with Kwikset residential smart garage door operators. The wireless keypad allows users to open and close up to four garage doors by means of user-defined sequences of numerical keys (codes). The length (number of digits) of a code can be unique for each garage door and range from 1 to 8 digits. FEATURES A keypad backlight turns on when any key is pressed for increased visibility and stays on for 5 seconds after the last key release or for 20 seconds after garage door activation from the keypad. A dual color GREEN and RED LED on the keypad signals correct and incorrect programming, respectively. KEYPAD 9V BATTERY (INSIDE KEYPAD) INSIDE KEYPAD: MOUNTING SCREWS x 2 SCREW ANCHORS x 2 1. Remove the small screw at the bottom of the keypad. 2. Separate the back mounting plate from the keypad. 3. Use the fasteners and anchors found inside the keypad to mount the keypad in your desired location no less than 5 ft (1.5m) off the ground. 4. Connect 9V battery found inside the keypad. 5. Snap keypad on mounting plate and fasten small bottom screw to secure keypad to mounting plate. INSTALLATION OPERATION Users enter a unique code on the keypad and press the ENTER () button. A radio signal is sent to the garage door opener and activates the corresponding garage door. For up to 20 seconds after the last keypad activation, user can stop and reverse the direction of the garage door quickly without having to re-enter the keypad code by pressing the ENTER button two times. SETTING KEYPAD CODES The keypad has no assigned codes from the manufacturer. Up to four codes for up to 4 garage doors, with length of 1 to 8 digits, can be activated. The available code locations are assigned in sequence. Once the four code locations have been assigned, trying to define a further code causes the RED LED to turn ON for 1 second, and the action is terminated with code changes. ACTION ACTION KEYPAD SEQUENCE & LIGHT DISPLAY KEYPAD SEQUENCE & LIGHT DISPLAY Create code for garage door Delete code for a garage door 2 Open/close garage door Incorrect code entered 3 Reverse direction of garage door Cancel code entered into keypad Factory Reset 4 Press unique 1-8 digits with less than a 5 second pause between each digit 1 , then press ENTER () for 3 seconds. Green LED will display for 2 seconds to confirm activated code. Press unique digits for code to be deleted, then press ENTER () for 5 seconds. Green LED will display for 2 seconds to confirm deleted code. Press unique digits for specific door, then press ENTER (). Green LED will display for 2 seconds and door will move. After pressing code for specific door and pressing ENTER (), Red LED will display for 2 seconds and door will not move. For up to 20 seconds after keypad activation, press ENTER () two times. Green LED will display for 2 seconds and door will stop and move in reverse direction. Press the “0” button on the keypad and hold for 3 seconds. Green LED will display for 1 second to confirm cancellation of code entry. Simultaneously press three buttons “1” “3” “8” on the keypad and hold for 3 seconds. Red LED will display for 10 second to confirm factory reset. 1 Pressed digit sequence is ignored if pause between entries is more than 5 seconds. Any incomplete key sequence is aborted after 10 seconds of inactivity, returning to stand-by condition. OTHER OPERATIONS The basic operational key sequences are indicated in the following table: Consult your local garage door installer for service. 2 The code must be active to be deleted. When deleted, the corresponding code location is freed and becomes available again for a new code. 3 Entering an incorrect code 10 consecutive times blocks the keypad for 2 minutes. 4 Factory reset erases all stored user codes. NOTE: The keypad will block all signals for 2 minutes when 25 numeric keypad presses occur with no more than 5 seconds between consecutive numeric presses. Kwikset_Keypad-Instructions_MECH.indd 14/14/25 2:16 PM DELETING KEYPAD CODE FROM OPENER Keypad codes can be deleted from the wall station and via the Kwikset app on your smartphone. 1. On the wall station display, press the ENTER button to get the main Frequent Use menu. 2. The wall station will display the Frequent Use FV code. Press ENTER. 3. Press the UP or DOWN button to move the display to the Radio Operations RO code. Press ENTER. 4. Press the UP or DOWN button to move the display to the Erase ER code. Press ENTER. 5. Press the code on the keypad that you want to delete. 6. Wall station will display OK when keypad code is deleted. Kwikset app on your smartphone will also confirm keypad code is removed. Wall station display Wall station display PROGRAMMING KEYPAD CODE TO OPENER Keypad codes can be added from the wall station and via the Kwikset app on your smartphone. 1. On the wall station display, press the ENTER button and hold for 2 seconds. 2. The wall station will display a SR code. 3. Press ENTER again, SR will begin flashing. 4. Press the code (just created on the keypad) on the keypad to program to the opener. 5. Wall station will display OK when keypad code is programmed. Kwikset app on your smart…

Text truncated - open the document above for the full version.

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Date: 29/0 5/2025 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Certification designating a U.S. agent for service of process. As required by section 2.911(d)(7), FCC ID: 2A8JO-FLXK315 We, ASSA ABLOY Entrance System AB 261 22 Landskrona, Box 131, Sweden FRN: 0032827735 certify that: Company name: Amarr Company address: 165 Carriage Ct., Winston Salem - 27150 North Carolina FRN: 0037069549 Contact person: Mr. David Bresson Contact e-mail: [email protected] Is our designated U.S. agent for service of process and we acknowledge: - our consent to accept service of process in the United States for matters related to the applicable equipment at the physical U.S. address and email address of the designated U.S. agent - the acceptance to maintain an U.S. agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. s Designated U.S. Agent Sincerely, ___________________________ By: Alexander Beck Title: Head of Shared Technologies & CTO Company: ASSA ABLOY Entrance System AB Telephone: +41799263620 e-mail: [email protected] We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address stated above. ____________________________ By: David Bresson Title: Product Manager Openers North America Company: Amarr Telephone: +1 336 251 1280 e-mail: [email protected]

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Date: 03/11/2025 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Oc hoa 2 & 6 29590 Campanillas Málaga, España Cer tifications concerning “covered” equipment. Section 2.911(d)(5)(i)- (ii) FCC ID: 2A8JO-FLX K315 We , ASSA ABLOY Entrance System AB, 261 22 Landskrona, Box 131, Sweden; certify that: Si ncerely, ________ __________________ By: Alexander Beck Title: Head of Shared Technologies & CTO Company: ASSA ABLOY Entrance System AB Telephone: +41799263620 e- mail: [email protected] -the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. - as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. - the equipment for which authorization is sought does not have any Kaspersky software installed.

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Date: 20/11/2025 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, Es paña Ref: sDoC declaration letter for FCC ID: 2A8JO-FLXK315 Pursuant to §15.101 of the Commission’s Rules (47 C.F.R.), ASA ABLOY Entrance Systems AB hereby declare that the device above mentioned is classified under the following equipment class/classes: JAB Part 15 Class B Digital Device JAD Part 15 Class A Digital Device JAV Other Non-Digital SDoC Devices JBP Part 15 Class B Computing Device/Personal Computer JBC Part 15 Class B Computing Device/Personal Computer CXX Communications Rcvr for use w/ licensed Tx and CBs CRR Superregenerative Receiver CYY Communications Receiver used w/Pt 15 Transmitter HID Part 15 TV Interface Device A nd will follow the Authorization procedure Supplier’s Declaration of Conformity prior to the initiation of marketing. Sincerely, _________________________ By: Alexander Beck Title: Head of Shared Technologies & CTO Company: ASSA ABLOY Entrance System AB Telephone: +41799263620 e- mail: [email protected]

Doc. KSWKP_SDoC - 1 - © ASSA ABLOY, All rights reserved Supplier’s Declaration of Conformity We: ASSA ABLOY Entrance Systems AB Lodjursgatan 10 SE-261 44 Landskrona Sweden e-mail: [email protected] Declare under our sole responsibility that the types of equipment with names: KWIKSET KSWKP 315MHz Remote Control Code Keypad Comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) these devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation. Responsible Party - U. S. Contact Information: Amarr 165 Carriage Ct., Winston Salem 27150 North Carolina ____________________________ By: David Bresson Title: Product Manager Openers North America Company: Amarr Telephone: +1 336 251 1280 e-mail: [email protected]

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Date: 29/0 5/2025 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Agent letter for FCC ID: 2A8JO-FLXK315 We, ASSA ABLOY Entrance System AB, 26122 Landskrona, Box 131, Sweden, hereby authorize DEKRA Testing and Certification S.r.l., Via della Fisica, 20, 36016 Thiene VI, Italy Mr. Fabio Carraro, e-mail: [email protected], Phone: +39 0445 367702 to act as our agent in the preparation of this application for equipment certification, including the signing of all documents relating to these matters. The present authorization considers the development of documents on behalf of the client, written under his own letterhead and related to the necessary information to be provided on his behalf to complete the certification process. We also hereby certify that neither we nor any party to this application are subject to a denial of U.S. Federal benefits, which include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by DEKRA Testing and Certification, S.A.U., still resides with us. This agreement expires one year from the current date. Sincerely, _________________________ By: Alexander Beck Title: Head of Shared Technologies & CTO Company: ASSA ABLOY Entrance System AB Telephone: +41799263620 e-mail: [email protected]

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Date: 29/0 5/2025 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Confidentiality request for FCC ID: 2A8JO-FLXK315 To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, ASSA ABLOY Entrance System AB hereby requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose: Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Internal Photos Short Term Permanent Operation Description Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term User’s Manual Short Term Permanent SDR software and security information Permanent Confidentiality: The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality: We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short-term confidentiality is: 45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date: We are also aware that we are responsible to notify DEKRA in the event information regarding the product or the product is made available to the public. DEKRA will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, __________________________ By: Alexander Beck Title: Head of Shared Technologies & CTO Company: ASSA ABLOY Entrance System AB Telephone: +41799263620 e-mail: [email protected]

ASSA ABLOY Entrance Systems AB Lodjursgatan, 10 SE-261 44 Landskrona Sweden Document Code: KSWKP_LAB Title: ASSA ABLOY Entrance Systems KWIKSET brand KSWKP 315MHz Remote Control Code Keypad Labels Design and Location Specifications Date: 13/06/2025 Authors: Juan J. Lloret M. Approval: Davide Braggion KSWKP Remote Control Code Keypad Labels Design and Location Specifications 0. Label General Requirements 0.1. Support type. White PET50 thermal transfer printing self-adhesive support, 0.10 ∼ 0.13 mm final thickness. 0.2. Printing ribbon. Black, high temperature resistant 275 °C, compliant with > 85% n-hexane 15-s rubbing test. 1. Product body data and conformity label - Label dimensions. 15 x 30 mm. - Label contents. The label will contain the following set of data: a. Manufacturer name and address (ASSA ABLOY E.S. AB ...) b. Product code (example: KSWKP) c. Battery type indication (“Battery: 6LR61 9 V”). Be aware of the spacing. d. FCC ID. Character size must be at least 4 points. The FCC ID code is: 2A8JO-FLXK315 e. IC ID. Same character size as FCC ID. The IC ID code is: 32396-FLXK315 f. HVIN. Same character size as FCC ID. The HVIN code is: FLXK315 g. QR-code with production details (product code, version, S/N, production batch, factory ID, TXID) h. WEEE product dismission symbol (crossed garbage can, with black segment in the bottom part). i. MES-code j. Production batch (YYWW) k. Serial no. l. Factory ID m. Product version 2 (2) Restricted - Label example (2:1 scale): 2. Product body Label placement. - The product body label will be attached to the lower part of the external right side face of the plastic product housing, according to the following figure:

DEKRA Testing and Certification S.r.l. Sede Operativa: Via della Fisica 20, 36016 Thiene (VI), Tel. +39 0445 367702 - [email protected] TRF N. 15-247_HoppingDEKRA Page 1 of 15 Test Report N. R25048501 rev.1.0 TEST REPORT Nr. R25048501 Federal Communication Commission (FCC) Report Reference N. .................. : R25048501 Date of issue: .............................. : 03.06.2025 Total number pages: ................... : 15 Customer name ......................... : ASSA ABLOY Entrance Systems AB Address ....................................... : Lodjursgatan, 10 – SE-261 44 Landskrona – Sweden Test specification: Standard(s) ................................. : KDB 447498 D01 General RF Exposure Guidance v06 Non-standard test method .......... : N/A Test Report Form N. .................. : 15-247_HoppingDEKRA Test Report Form(s) Originator ... : DEKRA Testing and Certification S.r.l. Master TRF ................................. : 2024-09 General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of DEKRA Testing and Certification S.r.l. (*) Test item description ........... : 315 MHz Code Keypad Radio Transmitter (*) Trademark .............................. : Kwikset (*) Manufacturer .......................... : ASSA ABLOY Entrance Systems AB (*) Model / Type reference .......... : KSWKP (*) FCC ID ................................... : 2A8JO-FLXK315 (*) Rating(s) ................................. : 9 Vdc from battery Report Tested by (name + signature) ..... : M. Segalla ............................................................. Approved by (name + signature) .................................... : F. Marenda ............................................................. (*) information provided by the customer TRF N. 15-247_HoppingDEKRA Page 2 of 15 Test Report N. R25048501 rev.1.0 1 Summary 1 Summary........................................................................................................................................... 2 2 Reference standard(s) ...................................................................................................................... 3 3 List of attachments ............................................................................................................................ 3 4 Deviation(s) from test specification ................................................................................................... 3 5 Testing location ................................................................................................................................. 3 6 General description of tested item and testing condition(s) ............................................................. 5 6.1 Photos of the test item ................................................................................................................. 6 7 Verdict summary section .................................................................................................................. 8 8 Test conditions .................................................................................................................................. 9 8.1 General ........................................................................................................................................ 9 9 Test results ..................................................................................................................................... 10 9.1 RF Exposure Analysis (as mobile device) ................................................................................. 10 9.2 RF Exposure Analysis (as portable device) .............................................................................. 11 TRF N. 15-247_HoppingDEKRA Page 3 of 15 Test Report N. R25048501 rev.1.0 2 Reference standard(s) KDB 447498 D01 General RF Exposure Guidance v06 RF exposure procedures and equipment authorization policies for mobile and portable devices 3 List of attachments Attachment 1: Measurement uncertainty, judgement of compliance and quality manual references 4 Deviation(s) from test specification None 5 Testing location DEKRA Testing and Certification S.r.l. Via della Fisica, 20 – 36016 Thiene (VI) – Italy Test site facility’s FCC registration number: 182474 Revision index Date Change history 1.0 03.06.2025 -- TRF N. 15-247_HoppingDEKRA Page 4 of 15 Test Report N. R25048501 rev.1.0 Testing and sampling: Date of receipt of test item .......................................... : 14.03.2025 Testing start date ........................................................ : 03.06.2025 Testing end date ......................................................... : 03.06.2025 Sampling procedure .................................................... : Sample used for testing chosen by the customer; DEKRA Testing and Certification S.r.l. cannot be considered responsible for the selection of the sample Internal identification ................................................... : Adhesive label with the product number P250300 General remarks: This report shall not be reproduced, except in full, without the written approval of DEKRA Testing and Certification S.r.l. The test results presented in this report relate only to the object tested. “(see appended table)": refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. Possible test case verdicts: Test case does not apply to the test object: N/A (Not Applicable) Test object meets the requirement: P (Pass) Test object does not meet the requirement: F (Fail) Test object was not evaluated for the requirement: N/E (Not Executed) Definition of symbols used in this test report: ☒ Indicates that the listed condition, standard or equipment is applicable for this report. ☐ Indicates that the listed condition, standard or equipment is not applicable for this report. TRF N. 15-247_HoppingDEKRA Pag…

Text truncated - open the document above for the full version.

DEKRA Testing and Certification S.r.l. Sede Operativa: Via della Fisica 20, 36016 Thiene (VI), Tel. +39 0445 367702 - [email protected] TRF N. 15-247_HoppingDEKRA Page 1 of 15 Test Report N. R25048501 rev.1.0 TEST REPORT Nr. R25048501 Federal Communication Commission (FCC) Report Reference N. .................. : R25048501 Date of issue: .............................. : 03.06.2025 Total number pages: ................... : 15 Customer name ......................... : ASSA ABLOY Entrance Systems AB Address ....................................... : Lodjursgatan, 10 – SE-261 44 Landskrona – Sweden Test specification: Standard(s) ................................. : KDB 447498 D01 General RF Exposure Guidance v06 Non-standard test method .......... : N/A Test Report Form N. .................. : 15-247_HoppingDEKRA Test Report Form(s) Originator ... : DEKRA Testing and Certification S.r.l. Master TRF ................................. : 2024-09 General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of DEKRA Testing and Certification S.r.l. (*) Test item description ........... : 315 MHz Code Keypad Radio Transmitter (*) Trademark .............................. : Kwikset (*) Manufacturer .......................... : ASSA ABLOY Entrance Systems AB (*) Model / Type reference .......... : KSWKP (*) FCC ID ................................... : 2A8JO-FLXK315 (*) Rating(s) ................................. : 9 Vdc from battery Report Tested by (name + signature) ..... : M. Segalla ............................................................. Approved by (name + signature) .................................... : F. Marenda ............................................................. (*) information provided by the customer TRF N. 15-247_HoppingDEKRA Page 2 of 15 Test Report N. R25048501 rev.1.0 1 Summary 1 Summary........................................................................................................................................... 2 2 Reference standard(s) ...................................................................................................................... 3 3 List of attachments ............................................................................................................................ 3 4 Deviation(s) from test specification ................................................................................................... 3 5 Testing location ................................................................................................................................. 3 6 General description of tested item and testing condition(s) ............................................................. 5 6.1 Photos of the test item ................................................................................................................. 6 7 Verdict summary section .................................................................................................................. 8 8 Test conditions .................................................................................................................................. 9 8.1 General ........................................................................................................................................ 9 9 Test results ..................................................................................................................................... 10 9.1 RF Exposure Analysis (as mobile device) ................................................................................. 10 9.2 RF Exposure Analysis (as portable device) .............................................................................. 11 TRF N. 15-247_HoppingDEKRA Page 3 of 15 Test Report N. R25048501 rev.1.0 2 Reference standard(s) KDB 447498 D01 General RF Exposure Guidance v06 RF exposure procedures and equipment authorization policies for mobile and portable devices 3 List of attachments Attachment 1: Measurement uncertainty, judgement of compliance and quality manual references 4 Deviation(s) from test specification None 5 Testing location DEKRA Testing and Certification S.r.l. Via della Fisica, 20 – 36016 Thiene (VI) – Italy Test site facility’s FCC registration number: 182474 Revision index Date Change history 1.0 03.06.2025 -- TRF N. 15-247_HoppingDEKRA Page 4 of 15 Test Report N. R25048501 rev.1.0 Testing and sampling: Date of receipt of test item .......................................... : 14.03.2025 Testing start date ........................................................ : 03.06.2025 Testing end date ......................................................... : 03.06.2025 Sampling procedure .................................................... : Sample used for testing chosen by the customer; DEKRA Testing and Certification S.r.l. cannot be considered responsible for the selection of the sample Internal identification ................................................... : Adhesive label with the product number P250300 General remarks: This report shall not be reproduced, except in full, without the written approval of DEKRA Testing and Certification S.r.l. The test results presented in this report relate only to the object tested. “(see appended table)": refers to a table appended to the report. Throughout this report a comma is used as the decimal separator. Possible test case verdicts: Test case does not apply to the test object: N/A (Not Applicable) Test object meets the requirement: P (Pass) Test object does not meet the requirement: F (Fail) Test object was not evaluated for the requirement: N/E (Not Executed) Definition of symbols used in this test report: ☒ Indicates that the listed condition, standard or equipment is applicable for this report. ☐ Indicates that the listed condition, standard or equipment is not applicable for this report. TRF N. 15-247_HoppingDEKRA Pag…

Text truncated - open the document above for the full version.

DEKRA Testing and Certification S.r.l. Sede Operativa: Via della Fisica 20, 36016 Thiene (VI), Tel. +39 0445 367702 - [email protected] Accredited by ACCREDIA according to UNI CEI EN ISO/IEC 17025 accreditation n. 0168 L TRF N. 15-231_DEKRA Page 1 of 36 Test Report N. R25048301 rev.1.0 LAB N° 0168 L TEST REPORT Nr. R25048301 Federal Communication Commission (FCC) Report Reference N. .................. : R25048301 Date of issue: .............................. : 30.05.2025 Total number pages: ................... : 36 Customer name ......................... : ASSA ABLOY Entrance Systems AB Address ....................................... : Lodjursgatan, 10 – SE-261 44 Landskrona – Sweden Test specification: Standards .................................... : FCC Rules & Regulations, Title 47:2023 Part 15 paragraph(s): 203, 204, 207, 209 and 231 Non-standard test method .......... : N/A Test Report Form N. .................. : 15-231_DEKRA Test Report Form(s) Originator ... : DEKRA Testing and Certification S.r.l. Master TRF ................................. : 2025-06 General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of DEKRA Testing and Certification S.r.l. (*) Test item description ........... : 315 MHz Code Keypad Radio Transmitter (*) Trademark .............................. : Kwikset (*) Manufacturer .......................... : ASSA ABLOY Entrance Systems AB (*) Model / Type reference .......... : KSWKP (*) FCC ID ................................…

Text truncated - open the document above for the full version.