2A8LTNH0001Connected Power HUB, White

CSHUB3WHI Quick Guide Guide Rapide Guía Rápida About / À propos / Acerca de For further guidance, capability and instruction please scan the QR Code. / Pour plus de conseils, de capacités et d'instructions, veuillez scanner le code QR. / Para obtener más orientación, capacidades e instrucciones, escanee el código QR. Honeywell International Inc. 12 Clintonville Rd, Northford, CT 06472 buildings.honeywell.com ©2023 Honeywell International Inc. 3013-8395-001 REV A Safety Instruction / Instruction de sécurité / Instrucción de seguridad Know Your Device / Connaissez votre appareil / Conozca su dispositivo RF MESH Indicator / MAILLE RF Indicateur / MALLA RF Indicador LAN Indicator / Réseau local Indicateur / LAN Indicador POWER Indicator / POUVOIR Indicateur / FUERZA Indicador LAN / Réseau local / LAN Commissioning Button / Bouton de mise en service / Botón de puesta en servicio Reset Button / Bouton de réinitialisation / Botón de reinicio White Wire / Fil Neutre / Cable neutral Ground Wire / Fil de terre / Cable de tierra Hot Wire / Fil chaud / Alambre caliente HOT= terminal marked L WHITE=terminal marked N GREEN= terminal marked Indicator / Indicatrice / Indicador Indicator Status / État de l'indicateur / Estado del indicador Description / Description / Descripción RF MESH Indicator / MAILLE RF Indicateur / MALLA RF Indicador LAN Indicator / Réseau local Indicateur / LAN Indicador POWER Indicator / POUVOIR Indicateur / FUERZA Indicador Green Flash / Flash vert / destello verde Yellow Flash / Flash jaune/ Luz amarilla Green Flash / Flash vert / destello verde Green Flash / Flash vert / destello verde Yellow Flash / Flash jaune/ Luz amarilla Green / Verte / Verde Bluetooth network normal / Réseau Bluetooth normal / red bluetooth normal All outlets under the hub leave / Tous les points de vente sous le hub partent / Todas las salidas debajo del centro salen Power on / Allumer / Encendido Commissioning mode / Mode de mise en service / Modo de puesta en marcha LAN normal / Réseau local normal/ LAN normal Network lost / Réseau perdu / Red perdida / Red perdida Installation Guide / À propos / Acerca de Installation / d'installation / instalación NOTE With a standard junction box, wall or ceiling installation is applicable for the installation. The following installation takes wall mounting as an example. 2 screws in box for installation, recommended screw sizes: P+ UNC 6-32 X 25 (X2). NOTE Avec une boîte de jonction standard, une installation au mur ou au plafond est applicable pour l'installation. L'installation suivante prend comme exemple le montage mural. 2 vis dans la boîte pour l'installation, tailles de vis recommandées : P+ UNC 6-32 X 25 (X2). NOTA Con una caja de conexiones estándar, se puede realizar la instalación en pared o techo. La siguiente instalación toma como ejemplo el montaje en pared. 2 tornillos en caja para instalación, tamaños de tornillos recomen dados: P+ UNC 6-32 X 25 (X2). Screw E537441 ≤2000m The Honeywell Connected Power Hub works in conjunction with Honeywell Connected Power Outlets. A Hub will support up to 50 Outlets and up to 50 Hubs will link into a Building Management System (BMS). The communica- tion between the Hubs and Outlets is via RF Mesh. The Hubs are wired into the BMS network. The Hub complies with UL / cUL62368-1, UL cUL 2043 (plenum) & FCC , IC. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation. Le Honeywell Connected Power Hub fonctionne conjointement avec les prises de courant connectées Honeywell. Un hub prendra en charge jusqu'à 50 points de vente et jusqu'à 50 hubs seront reliés à un système de gestion de bâtiment (BMS). La communication entre les hubs et les points de vente se fait via RF Mesh. Les Hubs sont connectés au réseau BMS. Le hub est conforme aux normes UL/cUL62368-1, UL cUL 2043 (plénum) et FCC, IC. Cet appareil est conforme à la partie 15 des règles FCC. Son fonctionne- ment est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer d'interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences susceptibles de provoquer un fonctionnement indésirable. El Honeywell Connected Power Hub funciona junto con las tomas de corriente conectadas de Honeywell. Un Hub admitirá hasta 50 Outlets y hasta 50 Hubs se conectarán a un Sistema de gestión de edificios (BMS). La comunicación entre los Hubs y Outlets es vía RF Mesh. Los Hubs están conectados a la red BMS. El concentrador cumple con UL/cUL62368-1, UL cUL 2043 (plenum) y FCC, IC. Este dispositivo cumple con la Parte 15 de las normas de la FCC. El funcionamiento está sujeto a las dos condi- ciones siguientes: (1) este dispositivo no puede causar interferencias dañinas y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un funcionamiento no deseado. Ensure that each wire is connected to the appropriate terminal, as shown in the back cover diagram. Each terminal accepts rigid (solid) or stranded cable up to 14 AWG conductors. Product and packaging should be disposed and / or recycled where appropriate at the end of their life. Only an authorized person should open the device enclosure. Assurez-vous que chaque fil est connecté à la borne appropriée, comme indiqué sur le schéma. Chaque borne accepte des câbles rigides (solides) ou toronnés jusqu'à 14 AWG de conducteurs. Le produit et l'emballage doivent être éliminés et/ou recyclés, le cas échéant, à la fin de leur durée de vie. Seule une personne autorisée doit ouvrir le boîtier de l'appareil. Asegúrese de que cada cable esté conectado al terminal apropiado, como se muestra en el diagrama. Cada terminal acepta cables rígidos (sólidos) o trenzados de hasta 14 AWG de conductores. El produ…

Text truncated - open the document above for the full version.

Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E APPENDIXES Equipment under Test: Connected Power HUB, White Model Number: CSHUB3WHI Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E01 Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E01

Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23102109-4E Page 1 of 5 APPENDIXES Equipment under Test: Connected Power HUB, White Model Number: CSHUB3WHI Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23102109-4E Page 2 of 5 Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23102109-4E Page 3 of 5 Antenna Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23102109-4E Page 4 of 5 Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23102109-4E Page 5 of 5 END OF APPENDIXES

Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 1 of 8 RF EXPOSURE REPORT Report No.: DDT-B23092109-4E04 Issued By: Tianjin Dongdian Testing Service Co., Ltd. Address: Building D-1, No. 19, Weisi Road, Microelectronics Industrial Park Development Area, Tianjin, China. Tel: +86-22-58038033, E-mail: [email protected], http://www.ddttest.com Applicant : Honeywell International Inc Address : 12 Clintonville Rd , Northford , CT 06472 , USA Equipment under Test : Connected Power HUB, White Model No. : CSHUB3WHI Trade Mark : FCC ID : 2A8LTNH0001 Manufacturer : MK Electric (M) Sdn Bhd Address : Komplek Perusahaan LTAT, Jalan Pengapit 15/19, Batu 3 Industrial Estate, 40000 Shah Alam, Selangor. Inspection & Testing Services Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 2 of 8 TABLE OF CONTENTS Test report declares......................................................................................................3 1. General information ........................................................................................................ 5 1.1. Description of Equipment ............................................................................................... 5 1.2. Assess laboratory ........................................................................................................... 6 2. RF Exposure Evaluation ................................................................................................ 7 2.1. Requirement ................................................................................................................... 7 2.2. Calculation method ........................................................................................................ 7 2.3. Estimation result ............................................................................................................. 8 Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 3 of 8 TEST REPORT DECLARE Standard Used: KDB447498 D01 General RF Exposure Guidance v06 We Declare: The equipment described above is assessed by Tianjin Dongdian Testing Service Co., Ltd and in the configuration assessed the equipment complied with the standards specified above. The assessed results are contained in this report and Tianjin Dongdian Testing Service Co., Ltd is assumed of full responsibility for the accuracy and completeness of these assess. After evaluation, our opinion is that the equipment In Accordance with above standard. Report No: DDT-B23092109-4E02 Date of Receipt: Oct. 11, 2023 Date of Test: Oct. 11, 2023 ~ Oct. 20, 2023 Prepared By: Approved By: ___________________ _____________________ Novak Wei/Engineer Aaron Zhang/Manager Note: This report applies to above tested sample only. This report shall not be reproduced in parts without written approval of Tianjin Dongdian Testing Service Co., Ltd. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. Applicant : Honeywell International Inc Address : 12 Clintonville Rd , Northford , CT 06472 , USA Equipment under Test : Connected Power HUB, White Model No. : CSHUB3WHI Trade mark : Manufacturer : MK Electric (M) Sdn Bhd Address : Komplek Perusahaan LTAT, Jalan Pengapit 15/19, Batu 3 Industrial Estate, 40000 Shah Alam, Selangor. Inspection & Testing Services Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 4 of 8 Revision History Rev. Revisions Issue Date Revised By --- Initial issue Oct. 23, 2023 Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 5 of 8 1. General information 1.1. Description of Equipment EUT* Name : Connected Power HUB, White Model Number : CSHUB3WHI EUT function description : Please reference user manual of this device Power supply : AC 125V 60Hz Radio Specification : BLE 5.0 Operation Frequency : 2402 MHz - 2480 MHz Modulation : GFSK Transmitter Rate : 1 Mbps,2 Mbps Antenna Type : PCB antenna, maximum PK gain: 1.43dBi Exposure category : General population/uncontrolled environment Device Type : Mobile Device Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 6 of 8 1.2. Assess laboratory Tianjin Dongdian Testing Service Co., Ltd. Address: Building D-1, No. 19, Weisi Road, Microelectronics Industrial Park Development Area, Tianjin, China. Tel: +86-22-58038033, http://www.ddttest.com, Email: [email protected] NVLAP (National Voluntary Laboratory Accreditation Program) CODE: 500036-0 CNAS (China National Accreditation Service for Conformity Assessment) CODE: L13402 FCC Designation Number: CN5004; FCC Test Firm Registration Number: 368676 ISED (Innovation, Science and Economic Development Canada) Company Number: 27768 Conformity Assessment Body Identifier: CN0125 VCCI Facility Registration Number: C-20089, T-20093, R-20125, G-20122 Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 7 of 8 2. RF Exposure Evaluation 2.1. Requirement Systems operating under the provisions of FCC 47 CFR section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device, and below RF Permissible Exposure limit shall comply with. Limits for General Population/Uncontrolled Exposure 2.2. Calculation method From the peak EUT RF output power, the minimum mobile separation distance, d=0.2 m, as well as the gain of the used antenna, the RF power density can be obtained. Tianjin Dongdian Testing Service Co., Ltd Report No.: DDT-B23092109-4E04 Page 8 of 8 2.3. Estimation result Worst Mode Max. Tune Up power (dBm) Output power (mW) Antenna Gain (dBi) Antenna Gain (linear) MPE Values (mW/cm 2 ) MPE Limit (mW/cm 2 ) BLE 2M…

Text truncated - open the document above for the full version.

Antenna Passive TEST REPORT Report No：DDT-B23110107-1E01 Issued By: Tianjin Dongdian Testing Service Co., Ltd. Address: Building D-1, No. 19, Weisi Road, Microelectronics Industrial Park, Development Area, Tianjin, China. Tel: +86-22-58038033, E-mail: [email protected], http://www.ddttest.com Applicant : Honeywell International Inc Applicant Address : 12 Clintonville Rd , Northford , CT 06472 , USA Equipment Under Test : Connected Power HUB, White （Antenna） Model No. : CSHUB3WHI Trade Mark : N/A Manufacturer : Honeywell International Inc Manufacturer Address : 12 Clintonville Rd , Northford , CT 06472 , USA Tianjin Dongdian Testing Service Co., Ltd Report No: DDT-B23110107-1E01 第2页 共13页 CONMENT 1. General TEST Information .................................................................................................... 5 1.1 Description of EUT ................................................................................................................ 5 1.2 Accessories of EUT .............................................................................................................. 5 1.3 Assistant equipment used for test ........................................................................................ 5 1.4 Block diagram of EUT configuration for test ......................................................................... 5 1.5 Measurement uncertainty ..................................................................................................... 5 1.6 Antenna Parameter ............................................................................................................... 6 1.7 Test laboratory ...................................................................................................................... 6 2. Near-field gain measurement ............................................................................................... 7 2.1 General Information .............................................................................................................. 7 2.2 Test Equipment ..................................................................................................................... 7 2.3 Block Diagram of Test Setup ................................................................................................ 7 2.4 Test Procedure ..................................................................................................................... 7 2.5 Result .................................................................................................................................... 8 3. Near-field pattern measurement ........................................................................................... 9 3.1 General Information .............................................................................................................. 9 3.2 Test Equipment ..................................................................................................................... 9 3.3 Block Diagram of Test Setup ................................................................................................ 9 3.4 Test Procedure ..................................................................................................................... 9 3.5 Result .................................................................................................................................. 10 Annex A Test Setup Photo ......................................................................................................... 13 Tianjin Dongdian Testing Service Co., Ltd Report No: DDT-B23110107-1E01 第3页 共13页 Revision History Rev. Revisions Issue Date Revised By --- Initial issue Nov. 02, 2023 Tianjin Dongdian Testing Service Co., Ltd Report No: DDT-B23110107-1E01 第4页 共13页 Test Report Declare We Declare: The equipment described above is tested by Tianjin Dongdian Testing Service Co., Ltd and in the configuration tested the equipment complied with the standards specified above. The test results are contained in this test report and Tianjin Dongdian Testing Service Co., Ltd is assumed of full responsibility for the accuracy and completeness of these tests. Report No: DDT-B23110107-1E01 Date of Receipt: Nov. 02, 2023 Date of Test: Nov. 02, 2023 Prepared By: Approved By: ____________________ ____________________ Novak Wei / Engineer Aaron Zhang / RF Manager Note: This report applies to above tested sample only. This report shall not be reproduced in parts without written approval of Tianjin Dongdian Testing Service Co., Ltd. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. Applicant : Honeywell International Inc Address : 12 Clintonville Rd , Northford , CT 06472 , USA Equipment under Test : Connected Power HUB, White （Antenna） Model No. : CSHUB3WHI Trade Mark : N/A Manufacturer : Honeywell International Inc Address : 12 Clintonville Rd , Northford , CT 06472 , USA Tianjin Dongdian Testing Service Co., Ltd Report No: DDT-B23110107-1E01 第5页 共13页 1. General TEST Information 1.1 Description of EUT EUT Description : Connected Power HUB, White （Antenna） Model Number : CSHUB3WHI Frequency Band : 2400MHz-2500MHz Power Supply : N/A Sample No : Y23110107-01 Note : N/A 1.2 Accessories of EUT Description of Accessories Manufacturer Model number Description Remark N/A N/A N/A N/A N/A 1.3 Assistant equipment used for test Description of Accessories Manufacturer Model number Description Remark N/A N/A N/A N/A N/A 1.4 Block diagram of EUT configuration for test 1.5 Measurement uncertainty Test Item uncertainty Near-field gain measurement 0.44 dB Near-field pattern measurement 0.44 dB Note: This uncertainty indicates that the extended uncertainty confidence interval is about 95% and the corresponding inclusion factor k=2 is obtained. EUT Tianjin Dongdian Testing Service Co., Ltd Report No: DDT-B23110107-1E01 第6页 共13页 1.6 Antenna Parameter 1.7 Test laboratory …

Text truncated - open the document above for the full version.

Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E01 QR-4-106-20 RevA0 Page 1 of 86 FCC CERTIFICATION TEST REPORT Report No.: DDT-B23092109-4E01 Issued By: Tianjin Dongdian Testing Service Co., Ltd. Address: Building D-1, No. 19, Weisi Road, Microelectronics Industrial Park Development Area, Tianjin, China. Tel: +86-22-58038033, E-mail: [email protected], http://www.ddttest.com Applicant : Honeywell International Inc Address : 12 Clintonville Rd , Northford , CT 06472 , USA Equipment under Test : Connected Power HUB, White Model No. : CSHUB3WHI Trade Mark : FCC ID : 2A8LTNH0001 IC : N/A Manufacturer : MK Electric (M) Sdn Bhd Address : Komplek Perusahaan LTAT, Jalan Pengapit 15/19, Batu 3 Industrial Estate, 40000 Shah Alam, Selangor. Inspection & Testing Services Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E01 QR-4-106-20 RevA0 Page 2 of 86 TABLE OF CONTENTS Test report declares.................................................................................................... ...3 1. Summary of Test Results ............................................................................................... 6 2. General Test Information ............................................................................................... 7 2.1. Description of EUT ......................................................................................................... 7 2.2. Accessories of EUT ........................................................................................................ 7 2.3. Assistant equipment used for test .................................................................................. 7 2.4. Block diagram of EUT configuration for test .................................................................. 8 2.5. Deviations of test standard............................................................................................. 8 2.6. Test environment conditions .......................................................................................... 9 2.7. Test laboratory ............................................................................................................... 9 2.8. Measurement uncertainty ............................................................................................. 10 3. Equipment Used During Test ....................................................................................... 11 4. 6 dB Bandwidth and 99% Bandwidth ........................................................................... 12 4.1. Block diagram of test setup .......................................................................................... 12 4.2. Limits ............................................................................................................................ 12 4.3. Test procedure ............................................................................................................. 12 4.4. Test result ..................................................................................................................... 13 4.5. Original test data .......................................................................................................... 13 5. Maximum Peak Output Power ..................................................................................... 20 5.1. Block diagram of test setup .......................................................................................... 20 5.2. Limits ............................................................................................................................ 20 5.3. Test procedure ............................................................................................................. 20 5.4. Test result ..................................................................................................................... 20 5.5. Original test data .......................................................................................................... 21 6. Power Spectral Density ................................................................................................ 24 6.1. Block diagram of test setup .......................................................................................... 24 6.2. Limits ............................................................................................................................ 24 6.3. Test procedure ............................................................................................................. 24 6.4. Test result ..................................................................................................................... 25 6.5. Original test data .......................................................................................................... 25 7. Band Edge Compliance (Conducted Method) ............................................................. 29 7.1. Block diagram of test setup .......................................................................................... 29 7.2. Limits ............................................................................................................................ 29 7.3. Test procedure ............................................................................................................. 29 7.4. Test result ..................................................................................................................... 30 7.5. Original test data .......................................................................................................... 30 8. Radiated Emission ....................................................................................................... 35 Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E01 QR-4-106-20 RevA0 Page 3 of 86 8.1. Block diagram of test setup .......................................................................................... 35 8.2. Limit ...........................................…

Text truncated - open the document above for the full version.

Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E Test Setup Photograph Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E Tianjin Dongdian Testing Service Co., Ltd. Report No.: DDT-B23092109-4E