2A8OL-FONECOM10FONECOM Video Intercom 10

1 Debian11 User manual Ver： V1.1 Date：2022-10-12 This manual is applicable to the product model：FONECOM-10 This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm fro m all persons and must not be co-located for operating in conjunction with any other antenna or transmitter. 2 Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil FCC warning： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation 3 Preface Dear users: Thank you for choosing our products! In order for you to use this product conveniently and quickly, we have provided the user manual with you. You can obtain information about the product introduction and instructions. Before using this product, please carefully read all the materials provided with us so that you can better use this product. During the preparation of this manual, we are very serious and rigorous. We hope to provide you with complete and reliable information. However, there are inevitably errors and omissions. Please understand. At the same time, we sincerely welcome your comments or suggestions. If you find any problems in the process of using this product, please contact us in time. Thank you for your support and cooperation The information in this manual is subject to change without notice. 4 points for attention 1.please read this manual carefully before using this product; 2.please keep this manual; 3.please place this product in a safe and stable place to avoid falling and injuring people; 4.The operation Temperature of this product is about -30° C ~ 70 ° C, and the relative humidity is 20% ~ 80%. Do not put it in a high-temperature or humid place; 5.Avoid collision between the machine and rigid objects, which may cause scratch or damage to the machine; 6.Avoid liquid flowing into the machine to cause damage to the machine; 7.Do not disassemble the internal and auxiliary power supply of the machine to prevent electric shock or fire; 8.Do not use overloaded electrical sockets to avoid electric shock or fire; 9.Be careful when plugging in the power supply. If you are not sure about the power supply voltage, please consult the local power company. Changes due to the performance and function of this product may occur without further notice. Thank you for your cooperation! 5 Specific operation and common functions are described as follows: 1 Power on and off  Power on：Plug in the adapter, and then insert the DC head into the machine. The system is powered on and enters the startup process. The startup logo is in the startup process, as shown below: After that, the system enters the default main interface.  Shut down：Unplug the DC head or unplug the AC line of the power adapter to directly shut down the machine. 6 2 Desktop After the system is started normally, you can see the Debian 11 system desktop, as shown in the following figure:  The default system desktop consists of: Recycle Bin, start menu, file manager, web browser, display desktop, desktop switch, taskbar, notification bar, etc. Click to perform the following operations:  start menu Common functions and settings of the system can be opened  File manager Open the file management window to open, copy, paste and delete files  Web browser For browsing the required web pages  Notice column It can quickly adjust the system volume, connect Bluetooth and WiFi, display time, Ethernet status, software running in the background, and quickly 7 shut down, log off, restart, etc 3 Start menu operation Click the start menu bar in the upper right corner of the desktop ，Pop up options are shown in the following figure: Use your finger to move the screen up and down to find and click ,You can perform some basic operations such as system settings and time functions. 4 System settings Click on the start menu，The system setting interface can be opened, as shown in the following figure: 8 Select relevant items to perform corresponding operations, for example:  Wi-Fi  Network  Bluetooth  Background  Notifications  Applications  Sound  Power  Displays  Date & Time  Users, etc 9 5 Date and time setting Click select，Enter the date and time setting interface as shown in the following fig…

Text truncated - open the document above for the full version.

Report No.: TW2208385-04E Applicant: Teleportivity Inc. Product: FONECOM Video Intercom 10 Model No.: FONECOM-10 Trademark: TELEPORTIVITY Test Standards: FCC Part 15 Subpart E, Paragraph 15.407 Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10, FCC Part 15 Subpart C, Paragraph 15.247 for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: October 10, 2022 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2208385-04E Page 2 of 95 Date: 2022-10-10 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with “Quality Law of People’s Republic of China” Clause 19. The testing quality system of our laboratory meet with ISO/IEC-17025 requirements, which is approved by CNAL. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 Report No.: TW2208385-04E Page 3 of 95 Date: 2022-10-10 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 5 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty............................................................................................... 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification.............................................................................................7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating …

Text truncated - open the document above for the full version.

R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] ShenzhenSKYLinkTechnologyCo.,Ltd AntennaSpecificationfor Approval CustomerName ： ProductName ：WIFIAntenna PartNO.:WF75B.C113.170B.1 WriteBy ：DamonCui IssuedDate:20 22 -09 -26 Customer R&D DeptBusinessDeptApprovedBy SKYLink R&D DeptEngineerDeptApproval R& D Center：Room D 5 th Floor Building L,Block E ,71 Baocheng District ,Baoan District ,Shenzhen Factory：6 Floor,GangHuaXing Industrial Park,Rongshu Road 2 nd ,Fuyong,Baoan ,shenzhen Email:[email protected] SpecificationSummary A. Electrical Characteristics Frequency2400MHz ~2500MHz 5150MHz~5850MHz VSWR<2.0 Efficiency>50% Peak Gain3.04dBi Impedance50 Ohm PolarizationLine B. Material & Mechanical Characteristics Material of RadiatorCu CableType1.13MM,Black Connector TypeI DimensionAt Attachment Heat-durability 280±5 ̊C，10sec. C. Environmental Characteristics Operation Temperature- 20 ̊C ~ + 80 ̊C Storage Temperature- 30 ̊C ~ + 85 ̊C R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] Test Equipment & Conditions 1．NetworkAnalyzers: Agilent8753D5071B CommunicationsTest Set: AgilentE5515CCMW500 2．3D ChamberTest System A 0.03 0.02 0.04 0～10 ±0.05 10～18 ±0.10 18～30 ±0.12 ∅ 0.02 30～40 ±0.15 Remark Rev Date Third Angle New drawing Description 40～ ±0.20 1 2 3 4 Approved by DCB 5 6 7 8 A 1 2 3 4 5 6 7 8 Part No. Date Designed by Checked by Scale Rev mm Location Project Material Part Name Unit RF MD A Angle ±0.5° 1:1 DCBA 深 圳 天 联 凌 科 技 有 限 公 司 SHEN ZHEN SKYLink CO.,LTD RoHS P G Compliant DWG No. 2022-09-26 WF75B.C113.170B.1 Remark Colour PartName No. 1 Black 2 Black FPC 注： 1."*"为重点尺寸 ; 2.未标注尺寸请依图纸； 3.Pb、Hg、Cr+6、PBBs、PBDEs各项小于1000PPM，Cd小于100PPM。 WF75B R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] ReturnLoss VSWR R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] Gain& Efficiency FreqEffiGainFreqEffiGain (MHz)(%)(dBi)(MHz)(%)(dBi) 240048.661.2515042.322.61 241048.751.3520042.512.6 242050.371.63525044.162.73 243052.612.05530043.622.43 244051.42.11535047.013.04 245048.391.855400472.69 246048.181.75545045.42.36 247049.041.55550046.152.57 248051.191.48555042.871.95 249054.811.89560042.862.2 250054.161.95565044.892.55 570044.532.8 5750462.21 580044.282.11 585045.612.61 R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] RadiationPattern R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] AntennaPicture R& D Center：RoomD 5 th Floor BuildingL,BlockE ,71 BaochengDistrict,BaoanDistrict,Shenzhen Factory：6 Floor,GangHuaXingIndustrialPark,RongshuRoad2 nd ,Fuyong,Baoan,shenzhen Email: [email protected] ReliabilityTest Test ItemTest conditionEquipmentSpecificationResult 1 Low Temp.Storage Test Temperature:-30°C，Time:48hrs Test condition:Placingantennain a Low/High TemperatureChamber,keepthe tempis 25°C and humidityis 65% for one hour,thenstep-down the temp.to -30°Cin one hour,storeantennafor 44 hours;step-uptempto 25°C,testantennaafter 2 hours. Temp.&Humi. Tester Nomaterial deformationis allowed. ElectronicPerformance is ok . PASS 2 HighTemp./High Humid StorageTest Temperature:85°CHumidity:85% RH Time:48hrs Test condition:Placingantennain a Low/High TemperatureChamber,keepthe tempis 25°C and humidityis 65% for one hour,thenstep-upthe temp.to 80°Cand the humidityup to 85% in one hour,storeantennafor 44 hours;step-downtemp to 25°C,testantennaafter2 hours. Temp.&Humi. Tester Nomaterial deformationis allowed. ElectronicPerformance is ok . PASS 3Salt-Spray6 pray Test Placingantennain the Salt-SprayTester,set the test condition，Temp:35±2°CHumidity:85% NaClsalt spray:5±1 %.PHvalue:6.5~7.2Test time:24hours Salt-SprayTester No colorchange No appearrusting PASS

Conducted Emission Test Setup: Radiated Emission Test Setup: