2A8RV-OVERWATCHPTZ Camera

Machine Translated by Google 21 Instructions for Quickly Deploying the Ball Eight, common problems and solutions common problemSolution Connect Can not boot battery drained the power adapter to charge and then turn it on The key is pressed for too short a time Please press and hold for at least 3 seconds Unable to turn off button press time is too short Please press and hold for at least 3 seconds, but no more than 10 seconds no SIM card insertedPlease insert a valid SIM card 3G/4G cannot SIM card in arrears Please recharge or replace the SIM card connect to the Internet If the SIM card is not activated for 3G/4G network, please contact the operator to activate it Current location 3G/4G signal is not covered or weak Change the ball position Select SSID is wrongSelect the corresponding SSID WIFI WIFI password error Enter the correct encryption type and password unable to connect Weak WIFI signal Appropriately close to the ball machine position WIFI signal is strong but connection is unstable Unable to locate the control ball Unable to locate successfully The current channel interference is serious, replace the relatively idle wireless channel The satellite signal needs to be received outdoors where the sky is visible, but cannot be received indoors; the problem of inability to locate may also occur under the viaduct. Machine Translated by Google 22 Instructions for Quickly Deploying the Ball 9. Appendix: Instructions for using the built-in router 1. Setup preparation 1.1 Connecting the device You can connect your computer and router by following steps. 1.1.1Set the IP address of the computer Before accessing the web settings page, it is recommended that you set your computer to "Obtain an IP address automatically" and "Obtain DNS server address automatically", the IP address is automatically assigned by the router. if you need To assign a static IP address to a computer, you need to associate the computer's IP address with the router's LAN port. The IP address is set in the same subnet (the default IP address of the router's LAN port is: 192.168.1.1, The subnet mask is 255.255.255.0). 1.1.2Connect via WiFi Detect the wireless network connection of the wireless router, then click the 'connect' button to establish the connection, wireless The password is: 12345678. Machine Translated by Google 23 Instructions for Quickly Deploying the Ball 1.1.3Confirm that the computer is connected to the router After your computer shows that the IP has been successfully obtained, use the Ping command to confirm that the computer and Whether the connection between routers is successful. For example, in Windows XP environment, execute the Ping command: Ping 192.168.1.1. like If the following screen is displayed, it means that the computer has successfully established a connection with the router. 1.2Log in to the router Next you will land on the router web settings page. Machine Translated by Google 24 Enter"http://192.168.1.1"intheaddressbarofthewebbrowser,andenterinthepop-upbox Login username and password. Whenyouloginforthefirsttime,pleaseenterthedefaultusername:admin,password:admin. Instructions for Quickly Deploying the Ball 1.3 Enter the router web settings page After successful login, enter the web setting page, then you can set and manage the router. made sense. Machine Translated by Google 25 Instructions for Quickly Deploying the Ball 2. Working mode Provides 4 working modes: 3G/4G wireless routing mode (default), standard wireless routing mode, Wireless AP+wireless client bridge mode, wireless AP+wireless client mode: Machine Translated by Google 26 Instructions for Quickly Deploying the Ball 2.1 3G/4G wireless routing mode. Thedefault of the dome router is 3G/4G wireless routing mode, insert the 3G/4G tariff card, the router will Automatically identify 3G/4G network. You can also define the network operator you need to choose. Machine Translated by Google 27 Carrier3G/4GNetworkAPNDial-UpNumberUsernamePassword ChinaMobileTD-SCDMA cmnet *99#or*98*1#card card ChinaTelecomCDMA2000 null #777Cardcard ChinaUnicomWCDMA 3G/4Gnet *99# skysky Instructions for Quickly Deploying the Ball 2.2Wired Access Standard Routing Mode 2.2.1 Static Internet access Enter the router management interface and select the standard routing mode for the working mode, and select the WAN setting to connect to the Internet. Select a static address, enter the IP address, network mask, gateway, DNS and other related parameters provided by the ISP, Click to confirm. Machine Translated by Google 28 Instructions for Quickly Deploying the Ball 2.2.2Dynamic Internet access Enter the working mode of the router management interface, select the standard routing mode, and set the WAN Internet access mode. Select the dynamic address, click OK, the router will automatically obtain the parameters assigned by the ISP. Machine Translated by Google 29 2.2.3 PPPoE Internet Access Mode Enter the router management interface working mode, standard routing mode, WAN settings Internet access mode selection PPPoE, enter the user name, password and other related parameters provided by the ISP, and clickOK. Instructions for Quickly Deploying the Ball 2.3Wireless AP+Client Bridge Mode After selecting this mode, we can use the dome router as a bridge AP for bridge Connect to the previous wireless router 2.3.1First set the local IP of the computer to 192.168.1.100, connect the LAN2 interface through the network cable, Enter the router management interface and select the wireless AP+client bridge mode. Machine Translated by Google 30 2.3.2ClickLANsettings,searchforwirelessnetworks, Instructions for Quickly Deploying the Ball Machine Translated by Google 31 2.3.3 You can see the valid wireless AP names within the current range, select the corresponding wireless AP 2.3.4 Enter the selected wireless AP password to bridge the previous wireless AP. Instructions for Quickly Deploying the Ball 2.4Wireless AP+Client Mode Router management interface - working mode - w…

Text truncated - open the document above for the full version.

Machine Translated by Google [Quickly deploy the ball] User ManualV2.0ÿPlease read this manual carefully before using itÿ Machine Translated by Google Table of contents 1.Safety Instructions ............................................................................................................ 1 2.Product parameters.................................................................................................4 3.Factory default parameters...................................................................................................8 1. Camera...................................................................................................................8 2. router. ................................................................................................ 8 3. WIFI. .................................................................................................... 8 4. Description of buttons and display screens............................................................................................9 1. Buttons:.....................................................................................................................9 2. Display Description:.........................................................................................................9 5. Special preset function.................................................................................................11 6. Installation Instructions ................................................................................................. 12 1. Power Cord Interface Definition...............................................................................12 2. Aviation plug connection........................................................................................................12 3. Rear Panel Interface Definitions. .................................................................................... 13 4. Tripod Mounting Method (Tripodis optional).......................................15 5. Dome size.........................................................................................................................17 6. Shock Bracket Dimensions...........................................................................................17 7. WiFi Instructions...................................................................................................................18 8. Common problems and solutions......................................................................................twenty one IX.Appendix: Instructions for using thebuilt-in router.......................................................................twenty two 1. Preparing for Setup...........................................................................................twenty two 2. Operating mode................................................................................................25 3. wireless security settings.............................................................................32 4. Device Management.................................................................................................40 Machine Translated by Google 1 Instructions for Quickly Deploying the Ball 1. Safety Instructions Personnel responsible for the installation and routine maintenance of this equipment must possess basic skills in safe operation. in operation Before using the device, be sure to carefully read and implement the safety regulations specified in the product manual. ÿ This is a Class A product, which may cause radio interference in a living environment. In this kind of In such cases, the user may be required to take practical measures for its interference. ÿ Make the equipment work within the allowable temperature and humidity range, and avoid being exposed to extrusion, vibration, humidity, etc. Dusty, extremely hot, extremely cold, strong electromagnetic radiation and other places. ÿ Under normal circumstances, the device is installed outdoors, and the device connection should be effectively waterproof and moisture-proof. Air, sand and dust prevention measures (especially the screws at the connection of the equipment must be tightened to ensure the overall tightness). To prevent lightning strikes, please install lightning arresters. ÿ Do not aim the lens at a strong light object for a long time, especially do not aim it at the sun or other strong objects. light source, otherwise it may cause permanent damage to the imaging device of the device. ÿ Please use the power adapter provided by our company. It is possible to use a power adapter that does not meet the requirements. can cause damage to the device. ÿ If the power cable between the power adapter and the device is too long, the voltage reaching the device will be low. It is easy to cause the equipment to work abnormally. If you need to extend the power cord, please refer to "Power Cord Requirements". ÿ Disconnect the power supply before moving the device. Be careful when moving it. Once the power cord is plugged into the power supply, The device will power up. When moving the equipment, do not carry the weight by the tail wire, so as to avoid the equipment cable The interface is loose. ÿ Do not cut the pigtails for connection. The exposed pigtails may cause a short circuit and cause abnormal damage to the device. Machine Translated by Google 2 Instructions for Quickly Deploying the Ball ÿ For external connection ports, please use existing cable terminals to connect. When connecting, confirm the cable terminal (lock buckle/snap) good and fastened in place; ÿ Do not pull the cable excessively during the installation process, and keep a certain margin to prevent vibration and shaking. Causes poor or loose port contact. ÿ The tail wire should not be exposed, and the area where the tail wire is located must be completely waterproof (waterproof junction box or seal). cavity); the tail wire needs to be waterproofed (see "Waterproof treatment of tail wire") to avo…

Text truncated - open the document above for the full version.

SmartBodyWireTechnologies,LLC OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2022-12-07 Subject;RequestforConfidentiality FCCID:2A8RV-OVERWATCH ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:FeliciaEdwards Title:Owner/Operator

! Letter of Authorization ! ! Company: Smart Body Wire Technologies, LLC ! Address: 1860 Sandy Plains Road Ste 204, PMB 2122, Marietta, Georgia 30066, United States ! Product Type: PTZ Camera ! Model Number(s): Predator OverWATCH ! Product Description: PTZ Camera ! ! ! We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. ! ! We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. ! ! Signature: Date: 2022-12-07 Name: Felicia Edwards Title: Owner/Operator Company: Smart Body Wire Technologies, LLC

Name：Predator OverWATCH Size：40*60mm Material：PVC PET Font type：Calibri Font color：White Paper color：Black Label location

FCC ID: 2A8RV-OVERWATCH Contains FCC ID:XMR201808EC25AF RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f 2 ) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f 2 ) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 , Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. FCC ID: 2A8RV-OVERWATCH Contains FCC ID:XMR201808EC25AF Test Result of RF Exposure Evaluation WIFI 2.4G Channel Max output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 2462MHz SISO@ANT 2 18.71 74.30 0.0298 1.0 PASS 802.11n(HT40) 2452MHz MIMO 19.09 81.10 0.0680 1.0 PASS Antenna gain: ANT 1: 3.48dBi ANT 2: 3.05dBi MIMO: 6.28dBi Band Output power (dbm) Power Density at R=20cm (mW/cm2) Limit (mW/cm2) Result WCDMA II 25.00 0.397 1.0 PASS WCDMA IV 25.00 0.199 1.0 PASS WCDMA V 25.00 0.550 0.55 PASS LTE band 2 25.00 0.397 1.0 PASS LTE band 4 25.00 0.199 1.0 PASS LTE band 5 25.00 0.550 0.55 PASS LTE band 12 25.00 0.470 0.47 PASS LTE band 13 25.00 0.520 0.52 PASS LTE band 14 25.00 0.530 0.53 PASS LTE band 66 25.00 0.199 1.0 PASS LTE band 71 25.00 0.450 0.45 PASS The maximum simultaneously transmitting were as below DTS+WCDMA: 0.618<1 DTS+LTE: 0.618<1 The max power density is less than MPE exempt limit, so it is compliance.

地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 承 认 书 SPECIFICATION FOR APPROVAL 客 户 名 称 CUSTOMER NAME: 产 品 名 称 PRODUCT NAME: 2.4G-PCB内置天线+端子，L=190mm WIFI(1.37灰色低损耗线）(②号) 客 户 料 号 CUSTOMER P/N: 优比电子料号 UB P/N: UB01C190F2D991A REV: A MANUFACTURER SIGNATURE CUSTOMER SIGNATURE CHECKED BY: APPROVED BY: DATE: 2019/12/24 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com Contents ltem Description 1.---------------------------------------------------------------规格表 2.---------------------------------------------------------------成品图 3.---------------------------------------------------------------测试报告 4. ------------------------------------------------------------天线安装示意图 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 1．规格表: 产品主要技术参数 主要技术指标 Main technical specifications 频率范围 （MHZ） 2400~2500 Frequency Range (MHZ) 2400~2500 特性阻抗(Ω) 50 Impedance(Ω) 50 平均增益(dBi) 2.84 AVG Gain(dBi) 2.84 输出电压 驻波比 ≤1.92 VSWR ≤1.92 最大功率 1W Admitted Power 1W 极化方式 线极化 Polarization Line 连接方式 Cable+端子 Connector Type Cable+Terminal 物理性能 Physical Properties 天线本体材料 PCB Antenna Base PCB 工作温度 -20°C~+70°C Operating Temp -20°C~+70°C 保存温度 -20°C~+70°C Storage Temp -20°C~+70°C 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 2.成品图： 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 3.测试报告：(样机调试数据) 3.1：网络分析仪测试数据 3.2：整机无源测试数据 Frequency / MHz Efficiency / % Gain/ dB 2400 46.99 3.93 2410 46.77 3.48 2420 46.45 2.82 2430 46.88 2.66 2440 46.88 2.58 2450 46.13 2.46 2460 45.81 2.42 2470 45.81 2.64 2480 45.71 2.73 2490 45.81 2.73 2500 44.98 2.78 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 3.3：暗室2D、3DRaditation Pattern(整机数据) 2400MHz phi 0 2D 2450MHz phi 90 2D 2500MHz Theta 90 2D 3.3.1：OTA测试数据 Measurement Band Channel Max Min Total TRP WIFI_B (11M) 1 18.62 -11.74 13.15 TRP WIFI_B (11M) 6 20.56 -8.57 14.62 TRP WIFI_B (11M) 11 18.83 -14.21 14.14 TIS(EIRP) WIFI_B (11M) 1 80.67 54.78 75.71 TIS(EIRP) WIFI_B (11M) 6 81.47 51.34 75.69 TIS(EIRP) WIFI_B (11M) 11 82.7 52.49 77.66 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 4.天线安装示意图 整机示意图 ②WIFI，注意Cable线 从PCB后面绕。

地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 承 认 书 SPECIFICATION FOR APPROVAL 客 户 名 称 CUSTOMER NAME: 产 品 名 称 PRODUCT NAME: 2.4G-PCB内置天线+端子，L=170mm WIFI（1.37灰色低损耗线）(④号) 客 户 料 号 CUSTOMER P/N: 优比电子料号 UB P/N: UB01C170F2D993A REV: A MANUFACTURER SIGNATURE CUSTOMER SIGNATURE CHECKED BY: APPROVED BY: DATE: 2019/12/24 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com Contents ltem Description 1.---------------------------------------------------------------规格表 2.---------------------------------------------------------------成品图 3.---------------------------------------------------------------测试报告 4. ------------------------------------------------------------天线安装示意图 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 1．规格表: 产品主要技术参数 主要技术指标 Main technical specifications 频率范围 （MHZ） 2400~2500 Frequency Range (MHZ) 2400~2500 特性阻抗(Ω) 50 Impedance(Ω) 50 平均增益(dBi) 2.61 AVG Gain(dBi) 2.61 输出电压 驻波比 ≤1.92 VSWR ≤1.92 最大功率 1W Admitted Power 1W 极化方式 线极化 Polarization Line 连接方式 Cable+端子 Connector Type Cable+Terminal 物理性能 Physical Properties 天线本体材料 PCB Antenna Base PCB 工作温度 -20°C~+70°C Operating Temp -20°C~+70°C 保存温度 -20°C~+70°C Storage Temp -20°C~+70°C 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 2.成品图： 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 3.测试报告：(样机调试数据) 3.1网络分析仪测试数据 3.2：整机无源测试数据 Frequency / MHz Efficiency / % Gain/ dB 2400 29.17 2.17 2410 29.79 2.42 2420 30.76 2.82 2430 31.7 2.96 2440 32.66 3.02 2450 33.34 3.05 2460 33.19 2.89 2470 32.21 2.65 2480 30.97 2.46 2490 30.34 2.37 2500 27.1 1.86 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 3.3：暗室2D、3DRaditation Pattern(整机数据) 2400MHz phi 0 2D 2450MHz phi 90 2D 2500MHz Theta 90 2D 3.3.1：OTA测试数据 Measurement Band Channel Max Min Total TRP WIFI_B (11M) 1 18.39 -15.69 11.69 TRP WIFI_B (11M) 6 20.95 -15.89 13.36 TRP WIFI_B (11M) 11 22.05 -17.96 13.98 TIS(EIRP) WIFI_B (11M) 1 72.48 35.37 68.64 TIS(EIRP) WIFI_B (11M) 6 75.07 39 69.55 TIS(EIRP) WIFI_B (11M) 11 76.72 41.16 69.41 地址：东莞市塘厦镇林村社区新太阳工业城79栋（东莞公司） 杭州市滨江区秋溢路500号乐通科技园3栋106室（杭州公司） 电话：0769-81777126 传真：0769-81777126 网址：www.ubuant.com 4.天线安装示意图 整机示意图 ④WIFI。

Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 1 of 83 1. Duty Cycle 1.1 Ant1 1.1.1 Test Result Ant1 Mode TX Type Frequency (MHz) T_on (ms) Period (ms) Duty Cycle (%) Duty Cycle Correction Factor (dB) Max. DC Variation (%) 802.11b SISO 2412 8.384 8.414 99.64 0.02 0.04 2437 8.384 8.414 99.64 0.02 0.04 2462 8.383 8.413 99.64 0.02 0.04 802.11g SISO 2412 1.394 1.428 97.62 0.10 0.03 2437 1.393 1.427 97.62 0.10 0.03 2462 1.393 1.427 97.62 0.10 0.00 802.11n (HT20) MIMO 2412 1.301 1.335 97.45 0.11 0.03 2437 1.302 1.336 97.46 0.11 0.03 2462 1.301 1.335 97.45 0.11 0.03 802.11n (HT40) MIMO 2422 0.649 0.683 95.02 0.22 0.00 2437 0.649 0.683 95.02 0.22 0.03 2452 0.649 0.683 95.02 0.22 0.07 Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 83 1.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 83 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 83 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_HCH_2462MHz_Ant1 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 5 of 83 802.11n(HT20)_LCH_2412MHz_Ant1 (MIMO)_NTNV 802.11n(HT20)_MCH_2437MHz_Ant1 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 6 of 83 802.11n(HT20)_HCH_2462MHz_Ant1 (MIMO)_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 7 of 83 802.11n(HT40)_MCH_2437MHz_Ant1 (MIMO)_NTNV 802.11n(HT40)_HCH_2452MHz_Ant1 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 8 of 83 2. Bandwidth 2.1 OBW 2.1.1 Test Result Mode TX Type Frequency (MHz) ANT 99% Occupied Bandwidth (MHz) Verdict Result 802.11b SISO 2412 1 13.823 Pass 2 14.235 Pass 2437 1 13.840 Pass 2 13.861 Pass 2462 1 13.898 Pass 2 13.960 Pass 802.11g SISO 2412 1 17.366 Pass 2 16.963 Pass 2437 1 17.364 Pass 2 16.965 Pass 2462 1 17.349 Pass 2 16.972 Pass 802.11n (HT20) MIMO 2412 1 18.116 Pass 2 17.758 Pass 2437 1 18.110 Pass 2 17.755 Pass 2462 1 18.120 Pass 2 17.768 Pass 802.11n (HT40) MIMO 2422 1 36.363 Pass 2 36.807 Pass 2437 1 36.327 Pass 2 36.853 Pass 2452 1 36.357 Pass 2 36.911 Pass Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 9 of 83 2.1.2 Test Graph 802.11b_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11b_LCH_2412MHz_Ant2 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 10 of 83 802.11b_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11b_MCH_2437MHz_Ant2 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 11 of 83 802.11b_HCH_2462MHz_Ant1 (SISO)_NTNV 802.11b_HCH_2462MHz_Ant2 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 12 of 83 802.11g_LCH_2412MHz_Ant1 (SISO)_NTNV 802.11g_LCH_2412MHz_Ant2 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 13 of 83 802.11g_MCH_2437MHz_Ant1 (SISO)_NTNV 802.11g_MCH_2437MHz_Ant2 (SISO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower …

Text truncated - open the document above for the full version.

Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 43 of 83 802.11n(HT20)_MCH_2437MHz_Ant2 (MIMO)_NTNV 802.11n(HT20)_MCH_2437MHz_MIMO_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 44 of 83 802.11n(HT20)_HCH_2462MHz_Ant1 (MIMO)_NTNV 802.11n(HT20)_HCH_2462MHz_Ant2 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 45 of 83 802.11n(HT20)_HCH_2462MHz_MIMO_NTNV 802.11n(HT40)_LCH_2422MHz_Ant1 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 46 of 83 802.11n(HT40)_LCH_2422MHz_Ant2 (MIMO)_NTNV 802.11n(HT40)_LCH_2422MHz_MIMO_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 47 of 83 802.11n(HT40)_MCH_2437MHz_Ant1 (MIMO)_NTNV 802.11n(HT40)_MCH_2437MHz_Ant2 (MIMO)_NTNV Report No.: GTSL202211000278F01 Global United Technology Services Co., Ltd. No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 89…

Text truncated - open the document above for the full version.