2A8YG-40239TETRIX 2.4 GHZ 4 CHANNEL WIRELESS GAMEPAD

The wireless gamepad transmitter must be linked to the receiver with a unique ID code in order to function properly. To do this, follow these steps. 1.Make sure the transmitter is switched OFF. 2.Install batteries in transmitter. Connect the battery pack to the receiver – RED LED will be flashing. 3.Press the CONNECT button on the side of the receiver – RED LED will change to a rapid flashing rate. 4.Press and hold down the CONNECT button on the transmitter. 5.While pressing the transmitter CONNECT button, switch the transmitter ON. 6.The RED LED on the receiver will change to solid. Release the transmitter CONNECT button. 7.The transmitter and receiver are now connected and ready for operation. Transmitter and Receiver Connection Procedure: CH2 CH1 CH4 FRONT BACK FRONT AND BACK CARD FOR GAMEPAD. SIZE IS 2.25” X 6”. FOLDED IN HALF TO FIT INTO CLAMSHELL PACKAGING IS OK. TRANSMITTER CH3 RECEIVER FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

PitscoEducationLLC 1003E.AdamsPittsburg,Kansas66762USA Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-9-13 To whom it may concern: We,PitscoEducationLLChereby certify that the equipment for which authorization is sought FCC ID: 2A8YG-40239is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist ) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Rainbow Wang Manager Pitsco Education LLC 62_[model]CoveredEqu_2.911(d)(5)(i)and(ii)-U,V03

PitscoEducationLLC 1003E.AdamsPittsburg,Kansas66762USA Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-9-13 U.S. Agent Designation Pitsco Education LLCacknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought FCC ID: 2A8YG-40239 Name and company of U.S. agent:Pitsco Education LLC Physical U.S. address of agent: 1003E.AdamsPittsburg,Kansas66762USA FRN of U.S. agent:0032983975 Email address of U.S. agent:[email protected] PitscoEducationLLCacknowledges their obligation to accept service of process on behalf of PitscoEducationLLC. Pitsco Education LLC with the FRN0032983975accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., orthe conclusion of any Commission- related administrative or judicial proceeding involving the equipment,whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Rainbow Wang Manager Pitsco Education LLC Signature Rainbow Wang Manager Pitsco Education LLC 48_[model]US_Agent_2.911(d)(7)-U,V05

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-9-13> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2A8YG-4023940239 For the product stated above, we request that the following information beheld confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Rainbow Wang/Manager Company: Pitsco Education LLC Address: 1003 E. Adams Pittsburg, Kansas 66762 USA Phone: 800-824-0496, 206 Fax: 800-824-0496, 206 E-Mail: [email protected]

PitscoEducationLLC 1003 E. Adams Pittsburg, Kansas 66762 USA Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-9-13 To whom it may concern: We,Pitsco Education LLCthe undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2A8YG-40239including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed onfollowing website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title ： Rainbow Wang/Manager Company: Pitsco Education LLC Address: 1003 E. Adams Pittsburg, Kansas 66762 USA Phone: 800-824-0496, 206 Fax: 800-824-0496, 206 E-Mail: [email protected]

FCC ID: 2A8YG-40239 TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2A8YG-40239 TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2A8YG-40239 TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT

FCC ID:2A8YG-40239 TB-RF-074-1.0 Appendix IID Label TETRIX 2.4 GHZ 4 CHANNEL WIRELESS GAMEPAD FCC ID:2A8YG-40239 Model: 40239 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2A8YG-40239 TB-RF-074-1.0 Appendix II ID Label Location

FCC ID: 2A8YG-40239 TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 7 Internal of EUT Photo 8 Internal of EUT FCC ID: 2A8YG-40239 TB-RF-074-1.0 Photo 9 Internal of EUT Photo 10 Appearance of PCB FCC ID: 2A8YG-40239 TB-RF-074-1.0 Photo 11 Appearance of PCB 2.4G Antenna

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202408-0268-5 Page: 1 of 3 TB-RF-074-1.0 1 A/F., Building.6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao’an, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2A8YG-40239 1. Client Information Applicant : Pitsco Education LLC Address : 1003 E. Adams Pittsburg, Kansas 66762 USA Manufacturer : Pitsco Education LLC Address : 1003 E. Adams Pittsburg, Kansas 66762 USA 2. General Description of EUT EUT Name : TETRIX 2.4 GHZ 4 CHANNEL WIRELESS GAMEPAD Model(s) No. : 40239 Model Difference : ---- Product Description : Operation Frequency: 2405MHz~2475MHz Antenna Gain: 1.9dBi PCB Antenna Power Supply : Input: DC 6V Software Version : VER1.0 Hardware Version : VER2.0 Remark: (1) The antenna gain provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. (2) The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Note: More test information about the EUT please refer the RF Test Report. Report No.: TBR-C-202408-0001-4 Page: 2 of 3 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤7.5.0 for 10-g SAR 2. Summary simultaneous transmission for SAR Exclusion The SAR exemption limits outlined in clause 4.3.2(b) of KDB 447498 have been derived based on an approximate SAR value of 0.4 W/kg using half-wave dipole antennas Footnote 1. As such, when simultaneous transmitter SAR evaluations include transmitters that have been exempt from routine SAR evaluation, the SAR must be estimating based on the ratio between the maximum tune-up tolerance limit of the transmitter that has been exempt and the exemption limit at the specific distance and frequency for that transmitter. This ratio must be multiplied by 0.4 W/kg(2.0 W/kg for controlled use and 1.0 W/kg for limb worn devices) in order to calculate the estimated SAR level. The estimate SAR value is calculated based the following equation: (maximum power level including tune-up tolerance for transmitter A / maximum power level of exemption at the same frequency and distance) * 0.4W/kg The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. Report No.: TBR-C-202408-0001-4 Page: 3 of 3 TB-RF-074-1.0 3. Calculation: Test separation: 5mm 2.4G Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.405 2.054 2±1 3 1.995 0.619 3.0 2.440 2.162 2±1 3 1.995 0.623 3.0 2.475 1.715 2±1 3 1.995 0.628 3.0 Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF REPORT-----

V . S .W . R < 1.4 Polarization Type V ertical & Horizontal Frequenc Range 2400 ~ 2500GHz Input Impendence(ohm) 50 Efficiency (dB) 6 0.2 % 6 0.2 %-3.61.91.2 Maximum Power (dBm)1.7 (XY-plane) Gain (dBi)1.2 (Avg Gain XY-plane) Peak EIRP(dBm)1.2 Tot. Rad. Pwr. (dBm)-1.2 (Input pwr – loss pwr) Product specification Quick Reference Date Antenna module on the system board Ant. Port Input Pwr. (dBm)0 (Typ. class 2 output power) Directivity (dBi)1 (all direction antenna) Minimum Power (dBm)-4(XY-plane) Avg. Power (dBm)-0.5(XY-plane) All the technical data and information contained herein are subject to change without prior notice Antenna Layout & module on the system board Antenna Gain Gain Table Unit in dBi @2.44GHzXY-planeXZ-planeYZ-planeEfficiency PeakAvg.PeakAvg.PeakAvg. Module Board -0.51.1-3.0 Return Loss The Environment of Antenna Radiation Pattern 3D radiation pattern diagram XY-planeXZ-planeYZ-plane

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 1 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 RF Test Data for 2.4G (Conducted Measurements) General Description of EUT Product Name: TETRIX 2.4 GHZ 4 CHANNEL WIRELESS GAMEPAD Test Model: 40239 Sample ID: HC-C-202408-0268-01-02# Environmental Conditions Temperature: 22.0°C-25°C Relative Humidity: 43%-55% Test Voltage: DC 3.8V Test Engineer: ZKN Zhou Note: For a more detailed features description, please refer to the report TBR-C-202408-0268-2 The report only show the worst case data. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 2 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Contents 1.Duty Cycle ............................................................................................................................................................................................ 3 2.Maximum Conducted Output Power .................................................................................................................................................. 6 3.-6dB Bandwidth ................................................................................................................................................................................... 9 4.Occupied Channel Bandwidth .......................................................................................................................................................... 12 5.Maximum Power Spectral Density Level .......................................................................................................................................... 15 6.Band Edge ......................................................................................................................................................................................... 18 7.Conducted RF Spurious Emission ................................................................................................................................................... 21 8.Restrict Band ..................................................................................................................................................................................... 25 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 3 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 1.Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT GFSK 2405 Ant1 9.93 10.03 1.02 NVNT GFSK 2440 Ant1 9.93 10.03 1.02 NVNT GFSK 2475 Ant1 9.83 10.07 1.03 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 4 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Test Graphs Duty Cycle NVNT 2405MHz Ant1 Duty Cycle NVNT 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 5 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Duty Cycle NVNT 2475MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 6 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 2.Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Limit (dBm) Verdict NVNT GFSK 2405 Ant1 2.054 30 Pass NVNT GFSK 2440 Ant1 2.162 30 Pass NVNT GFSK 2475 Ant1 1.715 30 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 7 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Test Graphs Power NVNT 2405MHz Ant1 Power NVNT 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 8 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Power NVNT 2475MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 9 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 3.-6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT GFSK 2405 Ant1 0.97 0.5 Pass NVNT GFSK 2440 Ant1 1.01 0.5 Pass NVNT GFSK 2475 Ant1 1.01 0.5 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 10 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 Test Graphs -6dB Bandwidth 2405MHz Ant1 -6dB Bandwidth NVNT 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 11 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 -6dB Bandwidth NVNT 2475MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202408-0268-2 Page: 12 of 27 FCC ID:2A8YG-40239 TB-RF-074-1.0 4.Occupied Channel Bandwidth Condition Mode Frequency (MHz) Antenna 99% OBW (…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202408-0268-2 Page: 1 of 36 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Radio Test Report FCC ID: 2A8YG-40239 Report No. : TBR-C-202408-0268-2 Applicant : Pitsco Education LLC Equipment Under Test (EUT) EUT Name : TETRIX 2.4 GHZ 4 CHANNEL WIRELESS GAMEPAD Model No. : 40239 Series Model No. : ---- Brand Name : ---- Sample ID : HC-C-202408-0268-01-01# & HC-C-202408-0268-01-02# Receipt Date : 2024-08-31 Test Date : 2024-08-31 to 2024-09-12 Issue Date : 2024-09-12 Standards : FCC Part 15 Subpart C 15.247 Test Method : ANSI C63.10: 2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Tested By : ZKN Zhou Reviewed By : Camille Li Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202408-0268-2 Page: 2 of 36 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT.............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST SOFTWARE ................................................................................................................... 10 4. TEST EQUIPMENT AND TEST SITE ................................................................................... 11 5. CONDUCTED EMISSION ....................................................................................................... 13 5.1 Test Standard and Limit .................................................................................................... 13 5.2 Test Setup ........................................................................................................................... 13 5.3 Test Procedure ................................................................................................................... 13 5.4 Deviation From Test Standard ......................................................................................... 14 5.5 EUT Operating Mode ........................................................................................................ 14 5.6 Test Data ............................................................................................................................. 14 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 15 6.1 Test Standard and Limit .................................................................................................... 15 6.2 Test Setup ........................................................................................................................... 16 6.3 Test Procedure ................................................................................................................... 17 6.4 Deviation From Test Standard ......................................................................................... 19 6.5 EUT Operating Mode ........................................................................................................ 19 6.6 Test Data ............................................................................................................................. 19 7. RESTRICTED BANDS REQUIREMENT ............................................................................. 20 7.1 Test Standard and Limit .................................................................................................... 20 7.2 Test Setup ........................................................................................................................... 20 7.3 Test Procedure ................................................................................................................... 21 7.4 Deviation From Test Standard ......................................................................................... 23 7.5 EUT Operating Mode ........................................................................................................ 23 Report No.: TBR-C-202408-0268-2 Page: 3 of 36 TB-RF-074-1.0 7.6 Test Data ............................................................................................................................. 23 8. BANDWIDTH TEST ................................................................................................................. 24 8.1 Test Standard and Limit .................................................................................................... 24 8.2 Test Setup ........................................................…

Text truncated - open the document above for the full version.

FCC ID: 2A8YG-40239 TB-RF-074-1.0 Appendix V EUT Test Photographs Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) -----END OF REPORT-----