2A93U-55041-402Geolocation System

Lifeseeker Mini TCB Authorization letter From: Centum research & technology S.L. Fontes das Abelleiras s/n Edificio Citexvi 36310 Vigo (Pontevedra) Spain To: Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: Vigo, February 22 nd , 2023 FCC ID: 2A93U-55041-402 To whom it may concern: We, Centum research & technology S.L. authorize Element Materials Technology Washington DC LLC, 7185 Oakland Mills Rd, Columbia, MD 21046 to act on our behalf in all matters relating to application for equipment authorization for the referenced FCC ID 2A93U-55041-402. Sincerely, Héctor Estévez Pomar Managing Director

Date: Vigo, February 2nd, 2023 FCC ID: 2A93U-55041-402 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Letter “Declaration of Conformity” Dear Sirs, The product referenced with the above FCC ID is defined as a SIGINT/COMINT system named Lifeseeker Mini. This system is defined to fulfill the ISO/IEC 17025 FCC Part 22, 24, 27 and ISO/IEC 17025 FCC Part 90 and it will apply and follow the “Declaration of Conformity” procedure. Test firm: Element Materials Techhnology Washington DC LLC 7185 Oakland Mills Road Columbia, MD 21046, USA Federal ID No. 52-1610288 Sincerely, David Casasnovas Chief of Operations Officer

U.S. AGENT LETTER OF ATTESTATION U.S. Agent: FRN: 0033440702 Name: LUMO Supply Deck Contact Name: Katia Lozano Address: 5126 W 139 th Street, Hawthorne, CA 90250 Telephone No: +1(310) 955-1330 Email: [email protected] To: Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: Vigo, February 16 th , 2023 ATTENTION: Federal Communications Commission (FCC) This letter is to confirm that we have accepted the responsibility to act as the U.S. based Agent on behalf of the Applicant noted below for all future FCC certification/registrations obtained during the period of this agreement which ends at the specified date below (if applicable). As the U.S. Agent, we are aware of the requirements involved as outlined in section 2.911(d)(7) of the FCC rules and of KDB 986446 D01v01. Applicant: FRN: 0033326158 Name: CENTUM research & technology S.L. Grantee Code: 2A93U Contact Name: Héctor Estévez Pomar Address: Fontes das Abelleiras s/n Edificio Citexvi. 36310 Vigo (Pontevedra) Spain Telephone No. +34986120460 Email: [email protected] We, CENTUM research & technology S.L. will maintain this agent in the U.S. for no less than one year after either all marketing or importation to the U.S. is terminated (or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment), whichever is later. LUMO Supply Deck CENTUM research & technology S.L. Katia Lozano Héctor Estévez Pomar CEO Managing Director 2/23/23

Lifeseeker Mini Attestation Letter From: Centum research & technology S.L. Fontes das Abelleiras s/n Edificio Citexvi 36310 Vigo (Pontevedra) Spain To: Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: Vigo, February 22 nd , 2023 RE: Covered Equipment for FCC ID: 2A93U-55041-402 To whom it may concern: We, Centum research & technology S.L. certify that the equipment for which it seeks an equipment authorization is not prohibited from receiving an equipment authorization pursuant to section 2.903. Section 2.903 (a) prohibits authorization of “covered” equipment. Per Section 2.911(d)(5)(i)- (ii) 1. Centum research & technology S.L. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. Centum research & technology S.L. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. The applicant certifies that neither the applicant nor any party to this application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the AntiDrug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. Sincerely, Héctor Estévez Pomar Managing Director

Confidentiality Request Letter Date: Vigo, March, 1 st , 2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD From: Centum research & technology Subject: Permanent Confidentiality Request for FCC ID: 2A93U-55041-402 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Centum research & technology hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04- 1705. This provision will give Centum research & technology temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Operational Descriptions 3 Parts Lists and Tune-Up Procedure 4 Schematics 5 Internal Photos (1) 6 User’s Manual (2) SHORT-TERM 5 External Photos 6 Test-Setup Photos The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Note 1: The Internal Photos must remain confidential because the internal components are not accessible to users. The circuit board is inside a rugged enclosure and void labels are used to avoid the manipulation of the screws from the customer/users. Note 2: The User’s Manual is a piece of information which the Applicant send to its customers (including end-users) only after signing a Non-Disclosure Agreement, and it is marked as confidential (red mark) during a period of at least, 5 years. Sincerely, David Casasnovas Chief of Operations Officer Centum research & technology

VERSION 1.31 DATE 21/02/2023 IDENTIFIER CRT-Q-LifeseekerMiniS10-Photos Lifeseeker Mini S10 Photos PAGE 8 of 12 CENTUM© CONFIDENTIAL 2. EXTERNAL PHOTOS Part Number: 550XX-XXX Figure 7: Front View. LED, On/Off button and RF connector for Antenna 1 VERSION 1.31 DATE 21/02/2023 IDENTIFIER CRT-Q-LifeseekerMiniS10-Photos Lifeseeker Mini S10 Photos PAGE 9 of 12 CENTUM© CONFIDENTIAL Figure 8. Back view. GPS, Power, Ethernet and RF Antenna 2 connectors VERSION 1.31 DATE 21/02/2023 IDENTIFIER CRT-Q-LifeseekerMiniS10-Photos Lifeseeker Mini S10 Photos PAGE 10 of 12 CENTUM© CONFIDENTIAL Figure 9. Right Side view VERSION 1.31 DATE 21/02/2023 IDENTIFIER CRT-Q-LifeseekerMiniS10-Photos Lifeseeker Mini S10 Photos PAGE 11 of 12 CENTUM© CONFIDENTIAL Figure 10. Left side view Figure 11. Top side view VERSION 1.31 DATE 21/02/2023 IDENTIFIER CRT-Q-LifeseekerMiniS10-Photos Lifeseeker Mini S10 Photos PAGE 12 of 12 CENTUM© CONFIDENTIAL Figure 12. Bottom side view LABEL LOCATION INFORMATION FOR LIFESEEKER MINI S10 FCC ID: 2A93U-55041-402 The label in the Product Lifeseeker Mini S10 is located on the bottom part of the chassis, as shown in the following picture: Figure 1. Bottom part of the product The following image shows a drawing of the final Label, including the FCC Logo and FCC ID on the product: Figure 2. Final FCC Label on the product This label is permanently affixed to the device by laser printing it to the outside of the plastic chassis (bottom part), ensuring its indelibility and the lasting according to the lifetime of the equipment.

LABEL ON EQUIPMENT FCC ID: 2A93U‐55041‐402 LIFESEEKER MINI S10

FCC ID: 2A93U-55041-402 PART 24 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 35 1M2212270143-02.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Centum Research & Technology S.L Fonte das Abelleiras S/N Edificio Citexvi 36310 Vigo (Spain) Date of Testing: 01/06/2023- 02/03/2023 Test Report Issue Date: 02/07/2023 Test Site/Location: Element Lab., Columbia, MD, USA Test Report Serial No.: 1M2212270143-02.2A93U FCC ID: Applicant Name: 2A93U-55041-402 Centum Research & Technology S.L Application Type: Certification Model: Lifeseeker Mini S10 EUT Type: Geolocation System FCC Classification: PCS Licensed Transmitter (PCB) FCC Rule Part: 24 Test Procedure(s): ANSI C63.26-2015 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RJ Ortanez Executive Vice President ELEMENT WASHINGTON DC LLC 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.element.com PART 24 MEASUREMENT REPORT FCC ID: 2A93U-55041-402 PART 24 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 35 1M2212270143-02.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. T A B L E O F C O N T E N T S 1.0 INTRODUCTION ........................................................................................................................................... 4 1.1 Scope ................................................................................................................................................................. 4 1.2 Element Test Location ........................................................................................................................................ 4 1.3 Test Facility / Accreditations ............................................................................................................................... 4 2.0 PRODUCT INFORMATION ........................................................................................................................... 5 2.1 Equipment Description ....................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................. 5 2.3 Test Configuration .............................................................................................................................................. 5 2.4 Software and Firmware ...................................................................................................................................... 5 2.5 EMI Suppression Device(s)/Modifications .......................................................................................................... 6 3.0 DESCRIPTION OF TESTS ........................................................................................................................... 7 3.1 Evaluation Procedure ......................................................................................................................................... 7 3.2 Radiated Power and Radiated Spurious Emissions ........................................................................................... 7 4.0 MEASUREMENT UNCERTAINTY ................................................................................................................ 8 5.0 TEST EQUIPMENT CALIBRATION DATA ................................................................................................... 9 6.0 SAMPLE CALCULATIONS ......................................................................................................................... 10 7.0 TEST RESULTS .......................................................................................................................................... 11 7.1 Summary .......................................................................................................................................................... 11 7.2 Conducted Output Power Data/ Equivalent Isotropic Radiated Power ............................................................. 12 7.3 Occupied Bandwidth ........................................................................................................................................ 15 7.4 Spurious and Harmonic Emissions at Antenna Terminal ................................................................................. 17 7.5 Band Edge Emissions at Antenna Terminal ...............................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2A93U-55041-402 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 6 1M2212270143-05.2A93U 01/06/2023- 01/23/2023 Geolocation System V 9.0 04/05/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without written permission from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Centum Research & Technology Fonte das Abelleiras S/N Edificio Citexvi 36310 Vigo (Spain) Date of Testing: 01/06/2023 – 01/23/2023 Test Report Issue Date: 02/23/2023 Test Site/Location: Element Lab. Columbia, MD, USA Test Report Serial No.: 1M2212270143-05.2A93U FCC ID: 2A93U-55041-402 APPLICANT: Centum Research & Technology Application Type: Certification EUT Type: Geolocation System FCC Classifications: PCS Licensed Transmitter (PCB) FCC Rule Part: FCC Part 1 (§1.1310) and Part 2 (§2.1091) Test Procedure(s): KDB 447498 D01 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in FCC KDB 447498 D01. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RJ Ortanez Executive Vice President ELEMENT WASHINGTON DC LLC 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.element.com RF EXPOSURE EVALUATION Maximum Permissible Exposure (MPE) FCC ID: 2A93U-55041-402 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 6 1M2212270143-05.2A93U 01/06/2023- 01/23/2023 Geolocation System V 9.0 04/05/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without written permission from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. TABLE OF CONTENTS 1.0 RF EXPOSURE EVALUATION – MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................ 3 1.1 Introduction ............................................................................................................................................ 3 1.2 EUT Description ..................................................................................................................................... 3 1.3 Procedure .............................................................................................................................................. 4 2.0 CONCLUSION ................................................................................................................................. 6 FCC ID: 2A93U-55041-402 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 6 1M2212270143-05.2A93U 01/06/2023- 01/23/2023 Geolocation System V 9.0 04/05/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without written permission from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. 1.0 R F E X P O S U R E E V A L U A T I O N – MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Introduction This document is prepared to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC Rules and Regulations and RSS-102 of Industry Canada. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is listed in Table 1-1. According to FCC §1.1310 and RSS-102: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits For Occupational / Control Exposures (f = frequency) 30-300 61.4 0.163 1.0 6 300-1500 ... ... f/300 6 1500-100,000 ... ... 5.0 6 (B) Limits For General Population / Uncontrolled Exposure (f = frequency) 30-300 27.5 0.073 0.2 30 300-1500 ... ... f/1500 30 1500-100,000 ... ... 1.0 30 Table 1-1. Limits for Maximum Permissible Exposure (MPE) 1.2 EUT Description The Equipment Under Test (EUT) is the Centum Geolocation System FCC ID: 2A93U-55041-402. The EUT can transmit two different LTE band signals at the same time with its multiple antenna port. EUT was set up to operate as shown below with a 12 VDC power source with current limitation of 10A. Server equipment was used to control the RF functions of the EUT. The EUT supports two output antennas and is capable of transmitting simultaneously on both antennas though not on the same band. The EUT supports operation in the following LTE Bands: B2 (1930 - 1990MHz) B12 (729 - 746 MHz) B13 (746 - 756 MHz) B26 (859 - 894 MHz) B66 (2110 - 2180 MHz) FCC ID: 2A93U-55041-402 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 6 1M2212270143-05.2A93U 01/06/2023- 01/23/2023 Geolocation System V 9.0 04/05/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any par…

Text truncated - open the document above for the full version.

FCC ID: 2A93U-55041-402 PART 22 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 31 1M2212270143-01.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Centum Research & Technology S.L Fonte das Abelleiras S/N Edificio Citexvi 36310 Vigo (Spain) Date of Testing: 01/06/2023 – 02/03/2023 Test Report Issue Date: 02/23/2023 Test Site/Location: Element Lab. Columbia, MD, USA Test Report Serial No.: 1M2212270143-01.2A93U FCC ID: Applicant Name: 2A93U-55041-402 Centum Research & Technology S.L Application Type: Certification Model: Lifeseeker Mini S10 EUT Type: Geolocation System FCC Classification: PCS Licensed Transmitter (PCB) FCC Rule Part: 22H Test Procedure(s): ANSI/TIA-603-E-2016 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RJ Ortanez Executive Vice President ELEMENT WASHINGTON DC LLC 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.element.com PART 22 MEASUREMENT REPORT FCC ID: 2A93U-55041-402 PART 22 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 31 1M2212270143-01.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. TABLE OF CONTENTS 1.0 INTRODUCTION ........................................................................................................................................... 4 1.1 Scope ................................................................................................................................................................. 4 1.2 Element Test Location ........................................................................................................................................ 4 1.3 Test Facility / Accreditations ............................................................................................................................... 4 2.0 PRODUCT INFORMATION ........................................................................................................................... 5 2.1 Equipment Description ....................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................. 5 2.3 Test Configuration .............................................................................................................................................. 5 2.4 EMI Suppression Device(s)/Modifications .......................................................................................................... 6 3.0 DESCRIPTION OF TESTS ........................................................................................................................... 7 3.1 Evaluation Procedure ......................................................................................................................................... 7 3.2 Cellular – Base Frequency Blocks...................................................................................................................... 7 3.3 Cellular – Mobile Frequency Blocks ................................................................................................................... 7 4.0 MEASUREMENT UNCERTAINTY ................................................................................................................ 8 5.0 TEST EQUIPMENT CALIBRATION DATA ................................................................................................... 9 6.0 SAMPLE CALCULATIONS ......................................................................................................................... 10 7.0 TEST RESULTS .......................................................................................................................................... 11 7.1 Summary .......................................................................................................................................................... 11 7.2 Transmitter Conducted Output Power/ Effective Radiated Power .................................................................... 12 7.3 Occupied Bandwidth ........................................................................................................................................ 15 7.4 Spurious and Harmonic Emissions at Antenna Terminal ................................................................................. 17 7.5 Band Edge Emissions at Antenna Terminal ..............................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2A93U-55041-402 PART 22 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 31 1M2212270143-01.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Plot 7-13. Conducted Spurious Plot (LTE Band 26 - 5MHz QPSK – Full RB - High Channel) FCC ID: 2A93U-55041-402 PART 22 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 31 1M2212270143-01.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. 7.5 Band Edge Emissions at Antenna Terminal Test Overview All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission is 43 + 10 log 10 (P [Watts] ), where P is the transmitter power in Watts. Test Procedure Used ANSI C63.26-2015 – Section 5.7.3 Test Settings 1. Start and stop frequency were set such that the band edge would be placed in the center of the plot 2. Span was set large enough so as to capture all out of band emissions near the band edge 3. RBW > 1% of the emission bandwidth 4. VBW > 3 x RBW 5. Detector = RMS 6. Number of sweep points ≥ 2 x Span/RBW 7. Trace mode = trace average for continuous emissions, max hold for pulse emissions 8. Sweep time = auto couple 9. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-4. Test Instrument & Measurement Setup Test Notes Per 22.917(b), in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed to demonstrate compliance with the out-of-band emissions limit. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. FCC ID: 2A93U-55041-402 PART 22 MEASUREMENT REPORT Approved by: Technical Manager Test Report S/N: Test Dates: EUT Type: Page 24 of 31 1M2212270143-01.2A93U 01/06/2023- 02/03/2023 Geolocation System V2 03/15/2021 Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from Element. If you have any questions about this or have an inquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. LTE Band 26…

Text truncated - open the document above for the full version.