2A9DRSF-1L4LBAX VISIO 10x32 WB

Swarovski-Optik AG & Co KG Agent Authorization Company: Swarovski-Optik AG & Co KG Address: Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Name: AX VISIO 10x32 WB Model Number(s): 10x32, SF-1L4LB0-0 Product Description: AX VISIO 10x32 WB with BT, 2.4G WiFi, 5G WiFi. We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2024.03.19 Name: Jiankuai Li Title: PM Company: Shenzhen STS Test Services Co., Ltd.

Differences Description We Swarovski-Optik AG & Co KG state: Product： AX VISIO 10x32 WB Model Name： 10x32, SF-1L4LB0-0 Trade Name: SWAROVSKI OPTIK FCC ID: 2A9DRSF-1L4LB The electrical circuit design, layout, components used and internal wiring for above models are identical, only different in model name Signatory Date: 2024-03-19 Signature Name: Jiankuai Li Title: PM Company: Shenzhen STS Test Services Co., Ltd.

Swarovski-Optik AG & Co KG Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024/03/19 Subject; Request for Confidentiality FCC ID: 2A9DRSF-1L4LB To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Jiankuai Li Title: PM

FCC Label FCC ID: 2A9DRSF-1L4LB

Page 1 of 88 FCC ID: 2A9DRSF-1L4LB Report No.: LCSA1229272E Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes noresponsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. SAR Test Report Report No.: LCSA1229272E Issued for Swarovski-Optik AG & Co KG Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Name: AX VISIO 10x32 WB Brand Name: SWAROVSKI OPTIK Model Name: 10x32 Series Model(s): SF-1L4LB0-0 FCC ID: 2A9DRSF-1L4LB Test Standards: ANSI/IEEE Std. C95.1-2019 FCC 47 CFR Part 2 ( 2.1093) IEEE 1528: 2013 Max. SAR Limb:0.118W/kg(10g) Body: 0.121W/kg(1g) Page 2 of 88 FCC ID: 2A9DRSF-1L4LB Report No.: LCSA1229272E Test Report Certification Applicant’s name ................. : Swarovski-Optik AG & Co KG Address ................................. : Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Manufacturer's Name ........... : Swarovski-Optik AG & Co KG Address ................................. : Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product description Product name ........................ : AX VISIO 10x32 WB Brand name ......................... : SWAROVSKI OPTIK Model name ......................... : 10x32 Series Model .......................... : SF-1L4LB0-0 Standards ............................. : ANSI/IEEE Std. C95.1-2019 FCC 47 CFR Part 2 ( 2.1093) IEEE 1528: 2013 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes noresponsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ........................................... : Date (s) of performance of tests ............. : 25 Dec 2023-29 Dec 2023 Date of Issue .......................................... : 29 Dec 2023 Test Result .............................................. : Pass Compiled by: Supervised by: Approved by: Jay Zhan / File administrators Cary Luo / Technique principal Gavin Liang/ Manager Page 3 of 88 FCC ID: 2A9DRSF-1L4LB Report No.: LCSA1229272E Table of Contents 1. General Information 5 1.1 EUT Description 5 1.2 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 6 1.3 Test Environment 7 1.4 Test Factory 7 2. Test Standards and Limits 8 3. SAR Measurement System 9 3.1 SAR Measurement Set-up 9 3.2OPENSAR E-field Probe System 10 3.3Phantoms 11 3.4Device Holder 12 3.5Scanning Procedure 12 3.6Data Storage and Evaluation 14 4. Tissue Simulating Liquids 16 4.1 Simulating Liquids Parameter Check 16 5. SAR System Validation 18 5.1 Validation System 18 5.2 Validation Result 19 6. SAR Evaluation Procedures 20 7. EUT Antenna Location Sketch 21 7.1 SAR test exclusion consider table 22 8. EUT Test Position 24 8.1 Body-worn Position Conditions 24 9. Uncertainty 25 9.1 Measurement Uncertainty 25 10. Conducted Power Measurement 27 10.1 Test Result 27 11. EUT and Test Setup Photo 30 11.1 EUT Photo 30 11.2 Setup Photo 31 12. SAR Result Summary 33 12.1 Limbs-worn SAR 33 12.2 Body-worn SAR 34 13. Equipment List 35 Appendix A. System Validation Plots 36 Page 4 of 88 FCC ID: 2A9DRSF-1L4LB Report No.: LCSA1229272E Appendix B. SAR Test Plots 42 CALIBRATION CERTIFICATES 50 Probe-EPGO376 Calibration Certificate 50 SID2450 Dipole Calibration Ceriticate 61 SID5-6G Dipole Calibration Ceriticate 73 SAR System PHOTOGRAPHS 86 SETUP PHOTOGRAPHS 87 EUT PHOTOGRAPHS 88 Revision History Rev. Issue Date Report No. Effect Page Contents 00 29 Dec 2023 LCSA1229272E ALL Initial Issue Page 5 of 88 FCC ID: 2A9DRSF-1L4LB Report No.: LCSA1229272E 1. General Information Environmental evaluation measurements of specific absorption rate (SAR) distributions in emulated human head and body tissues exposed to radio frequency (RF) radiation from wireless portable devices for compliance with the rules and regulations of the U.S. Federal Communications Commission (FCC). 1.1 EUT Description Product Name AX VISIO 10x32 WB Brand Name SWAROVSKI OPTIK Model Name 10x32 Series Model SF-1L4LB0-0 Model Difference Only different in Model name. Battery Rated Voltage: 3.6V Charge Limit Voltage:4.1V Capacity: 3.0Ah Device Category Portable Product stage Production unit RF Exposure Environment General Population / Uncontrolled Hardware Version Version 1c Software Version v1.0.4 Frequency Range WLAN802.11b/g/n20: 2412 MHz ~ 2462 MHz WLAN 802.11n40: 2422 MHz ~ 2452 MHz WLAN 802.11a/n20/n40/ac20/ac40/ac80: 5150 ~ 5250 MHz WLAN 802.11a/n20/n40/ac20/ac40/ac80: 5725 ~ 5850 MHz Bluetooth: 2402 MHz to 2480 MHz Max. Reported Band Mode Body Worn (W/kg) Limbs Worn (W/kg) DTS 2.4G WLAN 0.121 0.113 DSS BT 0.038 0.038 NII 5.2G WLAN 0.109 0.118 NII 5.8G WLAN 0.062 0.072 Limit SAR(1g):1.6W/kg SAR(10g):4.0W/kg FCC Equipment Class Part 15 Spread Spectrum Transmitter(DSS) Unlicensed National Information Infrastructure TX(NII) Digital Transmission System (DTS) Operating Mode: 2.4G WLAN : 802.11b(DSSS):CCK,DQPSK,DBPSK 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM 5G WLAN: 802.11a(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11ac(OFDM):BPSK,QPSK,16-QAM,64-QAM,256-QAM Bluetooth: GFSK +π/4DQPSK+8DPSK BLE: GFSK Antenna Specification: BT: Antenna: SR42W009 SMD Antenna WLAN: Antenna: SR42W009 SMD Antenna DTM Mode…

Text truncated - open the document above for the full version.

1. Features Antenna for 2.4 – 2.5 GHz and 5.17 – 5.84 GHz applications: Wi-Fi 802.11a/b/g/n/ac Works over a ground plane. No clearance required. Ideal for wearables. Maintains high performance on device: DFI (Designed For Integration)  SMD mounting Supplied on Tape and Reel 2. Description Trogona is intended for use with all dual-band Wi-Fi applications. Only requires a small ground plane and integrates into the corner with minimal PCB clearance area. The design is centered on being part of the device and not designing the device around the antenna. Trogona is ideal for single and MIMO antenna systems. 3.Applications Wearable devices Access Points Portable Devices PC-cards Game Consoles Set-Top-Box Network Devices MIMO Systems Trogona Dual-Band Wi-Fi Antenna SR42W009 lamiiANT ® Product Specification Antennas for Wireless Applications Product specification SR42W009-PS-1.6 page 1 Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 2 4.Part Number Trogona: SR42W009 5.General Data Product name Trogona Part Number SR42W009 Frequency 2.4-2.5 GHz; 5.17-5.84 GHz Polarization Linear Operating temperature -40°C to140°C Environmental Condition Test ISO16750-4 5.1.1.1/5.1.2.1/5.3.2 Impedance with matching 50 Ω Weight < 0.5 g Antenna type SMD Dimensions 19.3 x 3.3 x 4.4 (mm) 6.RF Characteristics Typical performance Conditions Peak gain 5.03dBi 2.4 – 2.5 GHz frequency range All data measured on Antenova’s evaluation PCB Part No. SR42W009- U1 Average gain -1.5dBi Average efficiency >70% Maximum return loss -7.0dB Maximum VSWR 2.7:1 Typical performance Conditions Peak gain 5.32dBi 5.175 – 5.835 GHz frequency range All data measured on Antenova’s evaluation PCB Part No. SR42W009- U1 Average gain -2.2dBi Average efficiency >60% Maximum return loss -7.0dB Maximum VSWR 2.70:1 Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 3 [MHz] [MHz] 7.RF Performance 7.1 Return Loss 5 [dB] Attune 0 -5 2 -10 1 -15 -20 -25 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 4200 4400 4600 4800 5000 5200 5400 5600 5800 6000 7.2 VSWR 10 [] Atyune 9 8 7 6 5 4 3 2 2 1 1 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 4200 4400 4600 4800 5000 5200 5400 5600 5800 6000 Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 4 7.3 Antenna patterns 7.3.1 2400 MHz – 2500 MHz 3D pattern at 2.45GHz Drag to rotate pattern and PCB by using Adobe Reader (Click to Activate) Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 5 7.3.2 4900 MHz – 5900 MHz 3D pattern at 5.5GHz Drag to rotate pattern and PCB by using Adobe Reader (Click to Activate) Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 6 8.Antenna Dimensions L W H Pin 1 L W H Length Width Height 19.3 3.3 4.4 All dimensions in mm Bottom side dimensions 4 solder pads (3.2 x 1.2 mm) Pin 1 Trogona Part No. SR42W009 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 7 9. Antenna footprint The recommended host PCB footprint is below. 4 copper pads all 3.2 x 1.2 (mm) 10. Schematic The circuit for the antenna and the matching components is below. The RF feed connection and GND connections are critical to the function of the antenna, and must be followed as shown. This circuit can be used for the circuit capture of the host PCB. Pin 2 the feed is connected to Pin 1 (GND) as shown below here and is essential to the antenna function. Pi Network 1 2 3 4 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 8 Trogona Part No. SR42W009 11.Electrical Interface 11.1 Transmission Line All transmission lines should be designed to have a characteristic impedance of 50Ω. • The length of the transmission lines should be kept to a minimum • Any other parts of the RF system like transceivers, power amplifiers, etc, should also be designed to have an impedance of 50 Ω Once the material for the PCB has been chosen (PCB thickness and dielectric constant), a coplanar transmission line can easily be designed using any of the commercial software packages for transmission line design. For the chosen PCB thickness, copper thickness and substrate dielectric constant, the program will calculate the appropriate transmission line width and gaps on either side of the feed. 11.2 Matching Circuit The antenna requires a matching circuit that must be optimized for each product. The matching circuit will require up to three components and the following pad layout should be designed into the device so the correct circuit can be installed. The Pi matching network must be placed close to the antenna feed to ensure it is more effective in tuning the antenna. Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 9 Trogona Part No. SR42W009 12.0 Antenna Integration Guide 12.1 Antenna Placement Whichever the host PCB size used, the antenna should be placed into the PCB corner. Ideally Pin 1 should be closest to the PCB edge. Pin 1 marker to PCB edge Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 10 Trogona Part No. SR42W009 12.2 Host PCB Layout The host PCB must ensure the footprint meets the antenna specification. An example of the PCB layout shows the antenna footprint. The antenna uses solder mask defined pads. Example host layout Below the footprint is shown again but without the solder mask. Pin 2 (feed) must be connected to pin 1 (GND) as shown here. 1 2 3 4 Pin 1 joined to Pin 2 Antennas for Wireless Applications Product Specification SR42W009-PS-1.6 Page 11 Trogona Part No. SR42W009 13.0 Reference Board The reference board has been designed for evaluation purposes of SR42W009 and includes a SMA female connector. SR42W009-U1 Evaluation Board 46mm 40mm To order a reference board, please see www.antenova.com Antennas for Wire…

Text truncated - open the document above for the full version.

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2309309W10 Issued for Swarovski-Optik AG & Co KG Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Name: AX VISIO 10x32 WB Brand Name: SWAROVSKI OPTIK Model Name: 10x32 Series Model(s): SF-1L4LB0-0 FCC ID: 2A9DRSF-1L4LB Test Standards: FCC Part15.247 Page 2 of 88 Report No.: STS209309W10 TEST REPORT Applicant’s Name ................. : Swarovski-Optik AG & Co KG Address .................................. : Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Manufacturer's Name ........... : Swarovski-Optik AG & Co KG Address .................................. : Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Description Product Name ........................ : AX VISIO 10x32 WB Brand Name ........................... : SWAROVSKI OPTIK Model Name ........................... : .. 10x32 Series Model(s) .................... : SF-1L4LB0-0 Test Standards ..................... : FCC Part 15.247 Test Procedure........................: ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ............................................ : Date of receipt of test item ...................... : 14 Sept. 2023 Date (s) of performance of tests ............. : 14 Sept. 2023 ~ 26 Dec. 2023 Date of Issue .......................................... : 26 Dec. 2023 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory: (Bovey Yang) Page 3 of 88 Report No.: STS209309W10 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 RADIATED EMISSION MEASUREMENT 15 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 31 4.1 LIMIT 31 4.2 TEST PROCEDURE 31 4.3 DEVIATION FROM STANDARD 31 4.4 TEST SETUP 31 4.5 EUT OPERATION CONDITIONS 31 4.6 TEST RESULTS 31 5. POWER SPECTRAL DENSITY TEST 32 5.1 LIMIT 32 5.2 TEST PROCEDURE 32 5.3 DEVIATION FROM STANDARD 32 5.4 TEST SETUP 32 5.5 EUT OPERATION CONDITIONS 32 5.6 TEST RESULTS 32 6. BANDWIDTH TEST 33 6.1 LIMIT 33 6.2 TEST PROCEDURE 33 6.3 DEVIATION FROM STANDARD 33 6.4 TEST SETUP 33 6.5 EUT OPERATION CONDITIONS 33 Page 4 of 88 Report No.: STS209309W10 Table of Contents Page 6.6 TEST RESULTS 33 7. PEAK OUTPUT POWER TEST 34 7.1 LIMIT 34 7.2 TEST PROCEDURE 34 7.3 DEVIATION FROM STANDARD 34 7.4 TEST SETUP 35 7.5 EUT OPERATION CONDITIONS 35 7.6 TEST RESULTS 35 8. ANTENNA REQUIREMENT 36 8.1 STANDARD REQUIREMENT 36 8.2 EUT ANTENNA 36 APPENDIX 1-TEST DATA 37 1. DUTY CYCLE 37 2. MAXIMUM AVERAGE CONDUCTED OUTPUT POWER 44 3. MAXIMUM PEAK CONDUCTED OUTPUT POWER 51 4. -6DB BANDWIDTH 52 5. MAXIMUM POWER SPECTRAL DENSITY LEVEL 59 6. BAND EDGE 66 7. CONDUCTED RF SPURIOUS EMISSION 75 APPENDIX 2-PHOTOS OF TEST SETUP 88 Page 5 of 88 Report No.: STS209309W10 Revision History Rev. Issue Date Report No. Effect Page Contents 00 26 Dec. 2023 STS2309309W10 ALL Initial Issue Page 6 of 88 Report No.: STS209309W10 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Page 7 of 88 Report No.: STS209309W10 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±1.197dB 2 Unwanted Emissions, conducted ±2.896dB 3 All emissions, radiated 9K-30MHz ±3.84dB 4 All emissions, radiated 30M-1GHz ±3.94dB 5 All emissions, radiated 1G-6GHz ±4.59dB 6 All emissions, radiated>6G ±5.22dB 7 Conducted Emission (9KHz-150KHz) ±2.14dB 8 Conducted Emission (150KHz-30MHz) ±2.54dB 9 Power Spectral Density, Conducted ±1.25dB 10 Occupied Channel Bandwidth ±3.5% Page 8 of 88 Report No.: STS209309W10 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name AX VISIO 10x32 WB Brand Name SWAROVSKI OPTIK Model Name 10x32 Series Model(s) SF-1L4LB0-0 Model Difference Only different in Model name. Product Description The EUT is a AX VISIO 10x32 WB Operation Frequency: 802.11b/g/n 20: 2412~2462 MHz 802.11n(40MHz):2422~2452MHz Modulati…

Text truncated - open the document above for the full version.

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2309309W11 Issued for Swarovski-Optik AG & Co KG Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Name: AX VISIO 10x32 WB Brand Name: SWAROVSKI OPTIK Model Name: 10x32 Series Model(s): SF-1L4LB0-0 FCC ID: 2A9DRSF-1L4LB Test Standards: FCC Part15.247 Page 2 of 79 Report No.: STS2309309W11 TEST REPORT Applicant’s Name ..................: Swarovski-Optik AG & Co KG Address ..................................: Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Manufacturer's Name ...........: Swarovski-Optik AG & Co KG Address ..................................: Daniel-Swarovski-Str 70, 6067 Absam, Tyrol, Austria Product Description Product Name .........................: AX VISIO 10x32 WB Brand Name ...........................: SWAROVSKI OPTIK Model Name ...........................:. .10x32 Series Model(s) .....................: SF-1L4LB0-0 Test Standards ......................: FCC Part15.247 Test Procedure .......................: ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ............................................ : Date of receipt of test item ...................... : 14 Sept. 2023 Date (s) of performance of tests ............. : 14 Sept. 2023 ~ 26 Dec. 2023 Date of Issue ........................................... : 26 Dec. 2023 Test Result ............................................... : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory: (Bovey Yang) Page 3 of 79 Report No.: STS2309309W11 Table of Contents 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 14 4. RADIATED EMISSION MEASUREMENT 15 4.1 RADIATED EMISSION LIMITS 15 4.2 TEST PROCEDURE 17 4.3 TEST SETUP 18 4.4 EUT OPERATING CONDITIONS 18 4.5 FIELD STRENGTH CALCULATION 19 4.6 TEST RESULTS 20 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 41 5.1 LIMIT 41 5.2 TEST PROCEDURE 41 5.3 TEST SETUP 41 5.4 EUT OPERATION CONDITIONS 41 5.5 TEST RESULTS 41 6. POWER SPECTRAL DENSITY TEST 42 6.1 LIMIT 42 6.2 TEST PROCEDURE 42 6.3 TEST SETUP 42 Page 4 of 79 Report No.: STS2309309W11 Table of Contents 6.4 EUT OPERATION CONDITIONS 42 6.5 TEST RESULTS 42 7. BANDWIDTH TEST 43 7.1 LIMIT 43 7.2 TEST PROCEDURE 43 7.3 TEST SETUP 43 7.4 EUT OPERATION CONDITIONS 43 7.5 TEST RESULTS 43 8. PEAK OUTPUT POWER TEST 44 8.1 LIMIT 44 8.2 TEST PROCEDURE 44 8.3 TEST SETUP 45 8.4 EUT OPERATION CONDITIONS 45 8.5 TEST RESULTS 45 9. ANTENNA REQUIREMENT 46 9.1 STANDARD REQUIREMENT 46 9.2 EUT ANTENNA 46 APPENDIX 1-TEST DATA 47 1. DUTY CYCLE 47 2. MAXIMUM AVERAGE CONDUCTED OUTPUT POWER 51 3. MAXIMUM PEAK CONDUCTED OUTPUT POWER 55 4. -6DB BANDWIDTH 59 5. MAXIMUM POWER SPECTRAL DENSITY LEVEL 63 6. BAND EDGE 67 7. CONDUCTED RF SPURIOUS EMISSION 72 APPENDIX 2- EUT TEST PHOTO 79 Page 5 of 79 Report No.: STS2309309W11 Revision History Rev. Issue Date Report No. Effect Page Contents 00 26 Dec. 2023 STS2309309W11 ALL Initial Issue Page 6 of 79 Report No.: STS2309309W11 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Page 7 of 79 Report No.: STS2309309W11 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±1.197dB 2 Unwanted Emissions, conducted ±2.896dB 3 All emissions, radiated 9K-30MHz ±3.84dB 4 All emissions, radiated 30M-1GHz ±3.94dB 5 All emissions, radiated 1G-6GHz ±4.59dB 6 All emissions, radiated>6G ±5.22dB 7 Conducted Emission (9KHz-150KHz) ±2.14dB 8 Conducted Emission (150KHz-30MHz) ±2.54dB 9 Power Spectral Density, Conducted ±1.25dB 10 Occupied Channel Bandwidth ±3.5% Page 8 of 79 Report No.: STS2309309W11 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name AX VISIO 10x32 WB Brand Name SWAROVSKI OPTIK Model Name 10x32 Series Model(s) SF-1L4LB0-0 Model Difference Only different in Model name. Product Description The EUT is a AX VISIO 10x…

Text truncated - open the document above for the full version.