2A9DV000002AGILE Destination Control Terminal (2023)

TKEC.CM-F-08-04j Product Design Center (China) Version: A No.: R1XXXXXXXX Technical Specification AGILE Destination Control Terminal (2023) Product Design Center (China) R1XXXXXXXX Version: A Copyright per GB/T 19827 i/i Product Design Center (China) Amendment Record Version Main Modification Content Last Modified A First version YYYY-MM-DD Preface It is a requirement that you shall read carefully and comprehend each item in this manual before any installation, operation, maintenance and usage of the elevator. If you have any trouble in fully understanding the literal content, diagrams or pictures in this manual, please contact TK Elevator (China) for necessary technical support. Please note that any incorrect installation, operation or maintenance may lead to potential abnormal operation of the elevator and then possible loss of property or injury of persons. 1. The installation and maintenance personnel of elevator must have obtained relevant legal operating certificate, and shall strictly observe the national and local regulations on safety, installation and maintenance during operation. If the national or local regulations on safety, installation and maintenance are inconsistent with this manual, please contact TK Elevator (China) for clarification beforehand. 2. The installation and maintenance personnel of elevator shall be professionally trained and instructed by TK Elevator (China). If unfamiliar with the relevant knowledge on installation or maintenance of TK Elevator, they shall immediately contact TK Elevator (China) for obtaining relevant information and instructions. 3. If inconsistency is found between any product mentioned in this manual and the actual one on the jobsite, be sure not to carry out any installation, operation or maintenance without authorization, and meanwhile immediately contact TK Elevator (China) for obtaining relevant information and instructions. 4. This manual has been scrutinized in technical details, and shall be immune from any prosecution for incomplete information. 5. TK Elevator (China) will be exempted from any liabilities to the damage or losses arising from nonobservance to this manual. 6. TK Elevator (China) expressly reserves the sole right to make changes to and update this manual at any time without opinion inquiry or prior notice. Please obtain the up-to-date product information, data and operation manuals via the official website mentioned below. 7. TK Elevator (China) reserves all the intellectual property rights and exclusive rights on this manual. Any copying or distribution of any part of this manual in any form which is not authorized by TK Elevator (China) with the express written approval is strictly forbidden. 8. Obtain the up-to-date product information, data and instructions of TK Elevator via the following ways: Official website: http://www.tkelevator.com.cn 24-hour service hotline: 400 820 0604 Nearest TK Elevator service branch. R1XXXXXXXX Ver: A Copyright per GB/T 19827 I/I Product Design Center (China) Contents (Optional) 1 Scope ................................................................................................................................................................ 1 2 Terms ............................................................................................................................................................... 1 3 Reference Standards .................................................................................................................................... 1 3.1 European Standards ..................................................................................................................................... 1 3.1.1 RF Radiation ................................................................................................................................................... 1 3.1.2 EMI ................................................................................................................................................................... 2 3.1.3 Others .............................................................................................................................................................. 2 3.2 US Standards ................................................................................................................................................. 2 3.2.1 RF Radiation .................................................................................................................................................. 2 3.2.2 Power line harmonics and fluctuations .................................................................................................... 3 3.2.3 EMI ................................................................................................................................................................... 3 3.3 China Standards............................................................................................................................................ 4 3.3.1 RF Radiation .................................................................................................................................................. 4 3.3.2 EMI ................................................................................................................................................................... 4 3.3.3 Environmental reliability test ..................................................................................................................... 4 3.3.4 Others .............................................................................................................................................................. 5 4 Models and Sizes .......................................................................................................................................... 5 4.1 Product Models ..............................................................................................................…

Text truncated - open the document above for the full version.

TK Elevator (China) Co., Ltd Current Date: 2023-02-10 To: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China. 201612 Dear Sir/Madam, Subject: Declaration Letter about Identity of Products *WE (TK Elevator (China) Co., Ltd) HEREBY DECLARED THAT Product Description AGILE Destination Control Terminal (2023) Model No. BUSNN008 Manufacturer’s Name Shanghai BST Electric Co.,ltd Manufacturer’s Address No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China *Except that the model number and size of screen deviation, are identical with the original product as follows: Note: The definition of identical should be “electrically identical”. A device will be considered to be electrically identical if no changes are made to the devices’ schematics, board layouts, component layouts, chip sets, resistors and all other electrical aspects of the device are identical with the model(s) we chose to be tested by SGS. Model No. (型号): BUSNN007 Manufacturer’s Name (生产商名称): Shanghai BST Electric Co.,ltd Manufacturer’s Address（生产商商地址): No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China Sincerely, Signature (签字): Printed Name (姓名): Victory Zhao Position/Title (职位): PM Contact Number (联系电话): +86 21 3786 9898

TK Elevator (China) Co., Ltd. Date: 2023-02-10 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2A9DV000002 To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with TK Elevator (China) Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Victory Zhao Title: PM Signature: On behalf of Company: TK Elevator (China) Co., Ltd. Telephone: +86 21 3786 9898

TK Elevator (China) Co., Ltd. 2023-02-10 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: TK Elevator (China) Co., Ltd.. NO. 11 & 13, Maling Daxin Road, South District, Zhongshan City, Guangdong Province, PRC. Regarding: Confidentiality Request regarding application for FCC ID: 2A9DV000002 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Signature: Printed Name: Victory Zhao Title: PM Company Name: TK Elevator (China) Co., Ltd.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 7 External Photos for KSCR2301000071AT Test Model No.: BUSNN007 Compliance Certification Services (Kunshan) Inc. Page: 2 of 7 EUT Constructional Details (EUT Photos) BUSNN007 Compliance Certification Services (Kunshan) Inc. Page: 3 of 7 Compliance Certification Services (Kunshan) Inc. Page: 4 of 7 Compliance Certification Services (Kunshan) Inc. Page: 5 of 7 BUSNN008 Compliance Certification Services (Kunshan) Inc. Page: 6 of 7 Compliance Certification Services (Kunshan) Inc. Page: 7 of 7

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 24 Internal Photos for KSCR2301000071AT Test Model No.: BUSNN007 Compliance Certification Services (Kunshan) Inc. Page: 2 of 24 EUT Constructional Details (EUT Photos) Compliance Certification Services (Kunshan) Inc. Page: 3 of 24 Compliance Certification Services (Kunshan) Inc. Page: 4 of 24 Compliance Certification Services (Kunshan) Inc. Page: 5 of 24 Compliance Certification Services (Kunshan) Inc. Page: 6 of 24 Compliance Certification Services (Kunshan) Inc. Page: 7 of 24 Compliance Certification Services (Kunshan) Inc. Page: 8 of 24 Compliance Certification Services (Kunshan) Inc. Page: 9 of 24 Compliance Certification Services (Kunshan) Inc. Page: 10 of 24 Compliance Certification Services (Kunshan) Inc. Page: 11 of 24 Compliance Certification Services (Kunshan) Inc. Page: 12 of 24 Compliance Certification Services (Kunshan) Inc. Page: 13 of 24 Compliance Certification Services (Kunshan) Inc. Page: 14 of 24 Compliance Certification Services (Kunshan) Inc. Page: 15 of 24 Compliance Certification Services (Kunshan) Inc. Page: 16 of 24 Compliance Certification Services (Kunshan) Inc. Page: 17 of 24 Compliance Certification Services (Kunshan) Inc. Page: 18 of 24 Compliance Certification Services (Kunshan) Inc. Page: 19 of 24 Compliance Certification Services (Kunshan) Inc. Page: 20 of 24 Compliance Certification Services (Kunshan) Inc. Page: 21 of 24 Compliance Certification Services (Kunshan) Inc. Page: 22 of 24 Compliance Certification Services (Kunshan) Inc. Page: 23 of 24 Compliance Certification Services (Kunshan) Inc. Page: 24 of 24 BT Antenna

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 1 of 10 Eric Lin EMC Laboratory Manager 1 Cover Page RF Exposure Evaluation Report Application No.: KSCR2301000071AT FCC ID: 2A9DV000002 Applicant: TK Elevator (China) Co., Ltd Address of Applicant: NO. 11 & 13, Maling Daxin Road, South District, Zhongshan City, Guangdong Province, PRC. 528455 Manufacturer: Shanghai BST Electric Co.,ltd Address of Manufacturer: No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China Factory: Shanghai BST Electric Co.,ltd Address of Factory: No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China Equipment Under Test (EUT): EUT Name: AGILE Destination Control Terminal (2023) Model No.: BUSNN007; BUSNN008 Trade mark: TKE Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2022-10-13 Date of Test: 2022-11-11 to 2022-12-05 Date of Issue: 2022-12-05 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 2 of 10 Revision Record Version Description Date Remark 00 Original 2022-12-05 / Authorized for issue by: Damon_Zhou /Project Engineer Eric Lin /Reviewer Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 3 of 10 2 Contents Page 1 COVER PAGE .................................................................................................................................... 1 2 CONTENTS ........................................................................................................................................ 3 3 GENERAL INFORMATION ................................................................................................................ 4 3.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................ 4 3.2 DETAILS OF E.U.T. ....................................................................................................................... 4 3.3 TEST LOCATION ............................................................................................................................ 5 3.4 TEST FACILITY .............................................................................................................................. 5 4 FCC RADIOFREQUENCY RADIATION EXPOSURE LIMITS .......................................................... 6 4.1 BLANKET 1 MW BLANKET EXEMPTION ........................................................................................... 6 4.2 MPE-BASED EXEMPTION .............................................................................................................. 6 4.3 SAR-BASED EXEMPTION ............................................................................................................... 7 5 MEASUREMENT AND CALCULATION ............................................................................................ 9 5.1 MAXIMUM TRANSMIT POWER ......................................................................................................... 9 5.2 RF EXPOSURE CALCULATION ........................................................................................................ 9 Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 4 of 10 3 General Information 3.1 General Description of E.U.T. Power supply: 20-28⎓0.7A MAX 44-57⎓400mA (POE+) Product Type: Portable device Mobile device Fixed device 3.2 Details of E.U.T. BLE Operation Frequency: 2402MHz to 2480MHz Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Data Rate: 1Mbps Antenna Gain: 2dBi(Provided by the manufacturer) Antenna Type: PCB Antenna 125kHz Operation Frequency: 125kHz Modulation Type: ASK Antenna Type: Loop Antenna 13.56MHz Operation Frequency: 13.56MHz Modulation Type: ASK Antenna Type: Loop Antenna Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 5 of 10 3.3 Test Location All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China. Tel: +86 512 5735 5888 Fax: +86 512 5737 0818 No tests were sub-contracted. Note: 1.SGS is not responsible for wrong test results due to incorrect information (e.g., max. internal working frequency, antenna gain, cable loss, etc) is provided by the applicant. (If applicable). 2.SGS is not responsible for the authenticity, integrity and the validity of the conclusion based on results of the data provided by applicant. (If applicable). 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA Compliance Certification Services (Kunshan) Inc. is accredited by the American Association for Laboratory Accreditation (A2LA). Certificate No. 2541.01. • FCC Compliance Certification Services (Kunshan) Inc. has been recognized as an accredited testing laboratory. Designation Number: CN1172. • ISED Compliance Certification Services (Kunshan) Inc. has been recognized by Innovation, Science and Economic Development Canada (ISED) as an accredited testing laboratory. Company Number: 2324E • VCCI The 3m and 10m Semi-anechoic chamber and Shielded Room of Compliance Certification Services (Kunshan) Inc. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-20134, R-11600, C-11707, T-11499, G-10216 respectively. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007104 Page: 6 of 10 4 FCC Radiofrequency radiation exposure limits Test exemptions apply for devices used in general population/uncontrolled exposure environments, according to the SAR-based, or MPE-based exemption thresholds. 4.1 Blanket 1 mW Blanket Exemption The 1 mW Blanket Exemption of §1.1307(b)(3)(i)(…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007102 Page: 1 of 24 Eric Lin Laboratory Manager TEST REPORT Application No.: KSCR2301000071AT FCC ID: 2A9DV000002 Applicant: TK Elevator (China) Co., Ltd Address of Applicant: NO. 11 & 13, Maling Daxin Road, South District, Zhongshan City, Guangdong Province, PRC. 528455 Manufacturer: Shanghai BST Electric Co.,ltd Address of Manufacturer: No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China Factory: Shanghai BST Electric Co.,ltd Address of Factory: No.2 hangfan Rd, Damaiwan Industrial Zone, Hangtou, Pudong, New, Area, Shanghai 201316, China Equipment Under Test (EUT): EUT Name: AGILE Destination Control Terminal (2023) Model No.: BUSNN007; BUSNN008¤ ¤ Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: TKE Standard(s) : 47 CFR Part 15, Subpart C Date of Receipt: 2022-10-13 Date of Test: 2022-12-05 to 2022-12-05 Date of Issue: 2022-12-05 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007102 Page: 2 of 24 Revision Record Version Description Date Remark 00 Original 2022-12-05 / Authorized for issue by: Damon_Zhou/Project Engineer Eric Lin /Reviewer Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007102 Page: 3 of 24 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at Mains Terminals (150kHz-30MHz) 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass 20dB Bandwidth ANSI C63.10 (2013) Section 6.9.2 47 CFR Part 15, Subpart C 15.215 Pass Radiated Emissions (9kHz-30MHz) ANSI C63.10 (2013) Section 6.4 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Emissions (30MHz-1GHz) ANSI C63.10 (2013) Section 6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Declaration of EUT Family Grouping: There are series models mentioned in this report, and they are the identical in electrical and electronic characters. The differences of the EUT BUSNN007 and BUSNN008 were model name and the size of screen. Only the model of BUSNN007 was tested since their differences. Compliance Certification Services (Kunshan) Inc. Report No.: KSCR230100007102 Page: 4 of 24 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ................................................................................. 9 6.1 ANTENNA REQUIREMENT ...................................................................................................................... 9 6.1.1 Test Requirement: ......................................................................................................................... 9 6.1.2 Conclusion ..................................................................................................................................... 9 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 10 7.1 CONDUCTED EMISSIONS AT MAINS TERMINALS (150KHZ-30MHZ) ........................................................ 10 7.1.1 E.U.T. Operation .......................................................................................................................... 10 7.1.2 Test Mode Description ................................................................................................................. 10 7.1.3 Test Setup Diagram ..................................................................................................................... 10 7.1.4 Measurement Procedure and Data............................................................................................. 11 7.2 20DB BANDWIDTH .............................................................................................................................. 14 7.2.1 E.U.T. Operation ..............................................................…

Text truncated - open the document above for the full version.

Justification statement for Antenna To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2A9DV000002 Dear Sir/Madam, Only radiated measurements are used for EUT with FCC ID: 2A9DV000002 to show compliance with FCC limits for fundamental and spurious emissions. All measurements were performed radiated and therefore additional antenna gain documentation is not required. The detailed information for antenna as below shows: Design Specifications Typical Antenna Type Loop Working Frequency 13.56 MHz&125kHz Overall Dimensions 47mm*31mm

Compliance Certification Services (Kunshan) Inc. Page: 1 of 4 Appendix Photographs of Test Setup for KSCR2301000071AT Test Model No.: BUSNN007 Compliance Certification Services (Kunshan) Inc. Page: 2 of 4 Test Setup Photo Conducted Emissions at AC Power Line (150kHz-30MHz) For 125KHz and 13.56MHz For BLE Compliance Certification Services (Kunshan) Inc. Page: 3 of 4 Radiated spurious emissions (Below 30MHz) For 125KHz and 13.56MHz Radiated spurious emissions (30MHz-1GHz) For 125KHz and 13.56MHz For BLE Compliance Certification Services (Kunshan) Inc. Page: 4 of 4 Radiated spurious emissions (Above 1GHz) For BLE Conducted Test setup For BLE