2A9HA-BM-100Brake light

1.1 Body Components and Names1.2 Additional Components and Names 2.2 Assembly of the main body2.1 Stand firewood ④ ① ① Main Body ② Controllers ③ Stand ③ As shown in the picture, align the two front hooks on the bottom of the main body with the two front holes on the stand and insert them. ① Remove all double sided tape protective paper from the bottom of the stand. ② Press and hold the stand firmly on the vehicle's dashboard in the desired position. ※ Attach the rear of the stand so that it is visible from the driver's seat as shown. ④ Position the front and rear hooks of the main body as shown in the figure and press them in the direction of the arrow to combine. Only when the front and rear hooks of the main body are coupled as shown in the figure, the main body and the stand are firmly fixed. ⑤ FrontFront ④ Power cable ⑤ Controller cable ⑥ Seager Jack ⑦ Cable clips ⑧ Double-sided tape for fixing the controller ⑨ Simple instruction manual ② ③ ⑤ ⑥ ⑦ ⑧ ○This product was produced after thorough quality control and inspection. If a failure occurs due to a manufacturing defect, we will provide free warranty service for one year from the date of purchase. However, failure due to user carelessness, disassembly, or other consumer negligence will be subject to the cost incurred even within the warranty period. ○The free warranty period is calculated from the purchase date, and if the purchase date is not confirmed, the warranty date is calculated from the manufacturing date, so please write down the purchase date. ○If you request an warranty, please make sure to provide a warranty. ○A/S inquiry Product warranty Device Name Model name Date of purchase date United Safety Front Brake Light Warranty period1 year from the date of purchase Authenticator trade name Manufacturer/ Country of Manufacture USFBL / KOREA Front Brake Light BL-D100, BL-M100 Front Break Light Easy User's Guide ● This manual provides performance improvements (hardware, software product configurations, etc.) without prior consent or notice from individual users for and other reasons.this is subject to change. Depending on the individual user's environment, the limitations or use of product performance and functionality It may not be possible. This product is an LED front brake light that can be used on the front or We're going to stop the vehicles and pedestrians approaching from the side Ali plays a role. Stand Rear Main Body Rear WWW.USFBL.COM ① Press the Register Sensor button. ② When you select a sensor from the Detected Sensors item, it is automatically registered. ③ Once registered, you will be automatically connected. ※ It automatically connects when the application is running. ※ If you register the same sensor, you will renew the existing one. ① Connection status icon ② Display current location ③ Vehicle parking position indication ④ Current Location Icon ⑤ Previous Automobile Location Icon ⑥ Last car location icon ① Red: Disconnected from sensor Blue:connected to sensor ② Move map to user's current location ③ Move map to previous parking position ④ Move the map to the last parking position ○Move Map: Drag or Click with Finger ○Zoom in on the map: Zoom in if you stretch your fingers with two fingers, Zoom in if you narrow your fingers. ○Map rotation: Turn left and right on the screen with two fingers ※What is a sensor? ●Sensor registration●Screen Item Description ● Start the vehicle and apply the brake to check if the front LED lamp is working. ● If the brake is not applied for more than 30 minutes, the power is automatically turned off, and when the brake is applied again, the power is automatically turned on and normal operation is performed. ※Precautions ○ Do not arbitrarily disassemble, assemble, or modify this product. ○The power cable must be supplied with the product. ○ Do not spray water on each part of the product or use wet patches, volatile alcohol, benzene, thinner, etc. when cleaning. ○ Stop using the product immediately if there is a strange sound, smell of burning, or smoke inside the product. ○Don't let children or dogs bite you. ※Cable clip Precautions for use Rear brake lamp cable Rear brake lamp cable Controller cable Black Line Black Line Red Line Red Line 3.2 Connecting Controllers3.1 Connecting Controllers ※It is very dangerous to attempt to disassemble or repair the product yourself. Never try to disassemble or repair the product yourself. ※If you have any questions or need service, please contact our Customer Service Center. 4. Product specification 5.1 Automotive Location App_Sensor Registration/ Screen Item Description 5.2 Functional description/map control of car positioning app ① ② ③ ① ② ③ ●Icon function description ●Map control ④ ⑤ ⑥ ① ② ③ ④ B0000001 B0000001 ※Map Control Area. Touch and drag one or two fingers on the screen. 2.3 Power Connection ※Body separation method ⑥⑥ After connecting the power jack and the power cable of the main body, connect them to the seager jack of the vehicle. ※The power jack is located on both sides of the left and right. ① Remove the rear hook of the main body by rotating it in the direction of the arrow as shown in the figure. ① After the controller gable is coupled with the controller, it is coupled to the rear brake wire of the vehicle using a cable clip as shown. ② After the controller gable is coupled with the controller, it is coupled to the rear brake wire of the vehicle using a cable clip as shown. Insert the rear brake lamp cable and the control cable into the center of the hole of the clip, position the end of the cable as shown in the figure by the control, and fasten the lock in the direction of the arrow. (Can't be reused when locked) ② Remove the rear hook of the main body by rotating it in the direction of the arrow as shown in the figure. FrontFront Refers to the internal sensor of the controller. Sensor registration is the same behavior as registering a controller. Device Name Model name Battery Rating Manufacturer Country Made Assember Name KC …

Text truncated - open the document above for the full version.

Rev 1/26/2023 UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January, 31, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A9HA-BM-100 Ji Woong, Kim of UNITED SAFETY FRONT BRAKE LIGHT LLC certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Manager / Ji Woong, Kim UNITED SAFETY FRONT BRAKE LIGHT LLC Rev 1/26/2023 UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January, 31, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A9HA-BM-100 UNITED SAFETY FRONT BRAKE LIGHT LLC certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Manager / Ji Woong, Kim UNITED SAFETY FRONT BRAKE LIGHT LLC

Rev 1/26/2023 UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January, 31, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2A9HA-BM-100 UNITED SAFETY FRONT BRAKE LIGHT LLC certifies that, as of the date of the filing of the application, TIMCO Engineering, Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. UNITED SAFETY FRONT BRAKE LIGHT LLC accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. TIMCO Engineering, Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: TIMCO Engineering, Inc. Address: 849 NW State Road 45, Newberry FL 32669 Contact Person: Bruno Clavier Tel.: 352-472-5500 Email: [email protected] Sincerely, UNITED SAFETY FRONT BRAKE LIGHT LLC TIMCO Engineering, Inc. Manager / Ji Woong, Kim Bruno Clavier (Applicant signature)

UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 Date: January 27, 2023 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 FCC ID: 2A9HA-BM-100 To whom it may concern: I, the undersigned, hereby authorize Young-Jin, Lee of KES Co., Ltd. and hereafter referred to as KES Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Young-Jin, Lee of KES Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KES Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Ji Woong, Kim UNITED SAFETY FRONT BRAKE LIGHT LLC REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

UNITED SAFETY FRONT BRAKE LIGHT LLC 4372 driving Range Rd, Corona CA, 9288, United States Tel: +82-10-8530-5752 Date: January 27, 2023 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2A9HA-BM-100 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT Exhibit Type File Name Part List Part List.pdf Schematics Diagram(s) Schematics.pdf Operation description Operation description.pdf Block diagram Block diagram.pdf And the above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Ji Woong, Kim UNITED SAFETY FRONT BRAKE LIGHT LLC

Model No.: BL-M100 Page 1 of 2 External photos Model No.: BL-M100 Page 2 of 2

Model No.: BL-M100 Page 1 of 1 Label Location

Model No.: BL-M100 Page 1 of 2 Internal photos Chip Antenna Model No.: BL-M100 Page 2 of 2 N/A

2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 1 of 5 *Efficiency based on Johanson's standard evaluation board ±± ±± ±± https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved Want the layout file? Request it at: https://www.johansontechnology.com/ask-a-question High Frequency Ceramic Solutions Part Number 11/5/2018 Avg. Rad Efficiency* Let us help you with the antenna design, optimization, and tuning! 2450AT18B100 2400 - 2500 76% General Specifications Frequency (MHz) -45 to +125°C -45 to +125°C 3000pcs Return Loss (dB) Impedance Input Power Storage Temperature Operating Temperature Reel Quantity 50 Ω 2 Watts max. (CW) Recommended Storage Conditions of unused product on T&R and period. +5 to +35°C Humidity 45~75%RH 18 months max. Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. e.g. 2450AT18B100(E or S)100% Tin Packing Style Evaluation Board 2450AT18B100-EB1SMA (see page 2&3 for details) Bulk (loose) T & R Suffix = E or S Suffix = E P/N Suffix Mechanical Dimensions In L 0.1260.0083.200.2 W 0.0630.0081.600.2 T 0.0511.30 +0.1/-0.2+.004/-.008 a 0.0200.0080.500.2 Terminal Configuration Function FEED NC No. 1 2 mm e.g. 2450AT18B100E e.g. 2450AT18B100SSuffix = S Part Number Explanation Peak Gain (dBi typ.) Average Gain (dBi typ.) 0.5 -0.5 9.5 min. ① ② L W a T 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 2 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Evaluation Board Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. To order a pre‐tuned 50Ω EVB with a female SMA connector click here: https://www.johansontechnology.com/request‐a‐sample Reference p/n: 2450AT18B100‐EB1SMA GND NO GND Units in mm ) ) 13.5 6.5 39.5 6.5 50Feed Line Antenna 4 ) Matching Component JTI P/Ns: L-14C2N7JV4 L-14C2N2JV4 * 2.6 4.2 1.6 1.9 0.4 2.7nH 1.2pF 3.3nH JTI P/N for Matching Circuit: Capacitor (1.2pF): 500R07S1R2BV4T Inductor (2.7nH): L-07C2N7SV6T Inductor (3.3nH): L-07C3N3SV6T *Line width should be designed to provied 50Ω impedance 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 3 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Typical Electrical Performance (T=25°C) Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Would you like the antenna layout? Have antenna tuning issues? Please contact us if you have any questions regarding the implementation of this antenna in your PCB's layout. We'll be happy to guide you to maximize the antenna's performance. Contact our applications engineers at: https://www.johansontechnology.com/ask‐a‐question 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 4 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 11/5/2018 Mounting Considerations 1: Antenna Performance Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. θ +Z (θ= 0°) +Y (θ= 90°) -Y -Z Typical 2D radiation patterns @ 2.44GHz YZ‐plane XZ‐plane XY‐plane Z Y Z X X Y φ +X (φ= 0°) -X +Y (φ= 90°) -Y θ +Z (θ= 0°) +X (θ= 90°) -X -Z 2.4GHz Mini Antenna, SMTP/N 2450AT18B100 Detail Specification: Page 5 of 5 https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 Ver. 4.0 2018 Johanson Technology, Inc. All Rights Reserved https://www.johansontechnology.com/rohs-compliance Need help designing the antenna in? Use our antenna design services! https://www.johansontechnology.com/ipc-antenna-services We provide 2 free layout reviews and if you need us to tune and characterize the antenna on your product (inside our anechoic chamber) we can do that too. Small lab fee may apply. High Frequency Ceramic Solutions Antenna tuning, optimization, and validation services: For more antennas and to download measured S-parameters, go to: 11/5/2018 Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. RoHS Compliance Soldering Information For layout review contact our Applications Team at: MSL Info Packaging information https://www.johansontechnology.com/ipc-antenna-services https://www.johansontechnology.com/antennas https://www.johansontechnology.com/ipcsoldering-profile https://www.johansontechnology.com/msl-rating https://www.johansontechnology.com/tape-reel-packaging https://www.johansontechnology.com/ask-a-question

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (1) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 EMC TEST REPORT Test Report No. : KES-EM-23T0072 Date of Issue : Jan. 27, 2023 Product name : Brake light Model/Type No. : BL-M100 Variant Mode : - Applicant : UNITED SAFETY FRONT BRAKE LIGHT LLC Applicant Address : 4372 driving Range Rd, Corona CA, 9288 Manufacturer : UNITED SAFETY FRONT BRAKE LIGHT LLC Manufacturer Address : 4372 driving Range Rd, Corona CA, 9288 FCC ID : 2A9HA-BM-100 Date of Receipt : Nov. 28, 2022 Test date : Dec. 22, 2022 Test Results : In Compliance Not in Compliance Tested by Reviewed by Min Seong, Kim EMC Test Engineer Dong Hun, Jang EMC Technical Manager KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (2) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 REPORT REVISION HISTORY Date Test Report No. Revision History Jan. 27, 2023 KES-EM-23T0072 Issued This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. This document may be altered or revised by KES Co., Ltd. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KES Co., Ltd. will constitute fraud and shall nullify the document. KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (3) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 TABLE OF CONTENTS 1.0 General Product Description.................................................................................... 4 1.1 Test Voltage & Frequency ....................................................................................... 5 1.2 Variant Model Differences ....................................................................................... 5 1.3 Device Modifications .............................................................................................. 5 1.4 Equipment Under Test ............................................................................................ 5 1.5 Support Equipments .............................................................................................. 5 1.6 External I/O Cabling .............................................................................................. 6 1.7 EUT Operating Mode(s) .......................................................................................... 6 1.8 Configuration ........................................................................................................ 7 1.9 Remarks when standards applied ............................................................................ 8 1.10 Calibration Details of Equipment Used for Measurement .............................................. 8 1.11 Test Facility .......................................................................................................... 8 1.12 Measurement Procedure ......................................................................................... 8 1.13 Laboratory Accreditations and Listings ..................................................................... 9 2.0 Test Regulations .................................................................................................. 10 2.1 Conducted Emissions at Mains Power Ports ............................................................. 11 2.2 Radiated Electric Field Emissions(Below 1 ㎓) ......................................................... 13 2.3 Radiated Electric Field Emissions(Above 1 ㎓) ......................................................... 15 APPENDIX A – TEST DATA............................................................................................. 17 Conducted Emissions at Mains Power Ports ................................................................ 17 Radiated Electric Field Emissions(Below 1 ㎓) ............................................................ 19 Radiated Electric Field Emissions(Above 1 ㎓) ............................................................ 20 APPENDIX B - Test Setup Photos and Configuration.......................................................... 22 Radiated Electric Field Emissions(Below 1 ㎓) ............................................................ 23 Radiated Electric Field Emissions(Above 1 ㎓) ............................................................ 24 KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (4) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 1.0 General Product Description Main Specifications of EUT are: Division Specification Input power DC 12 V…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (22) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 APPENDIX B - Test Setup Photos and Configuration Conducted Emissions at Mains Power Ports N/A KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (23) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 Radiated Electric Field Emissions(Below 1 ㎓) KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-EM-23T0072 Page (24) of (24) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 Radiated Electric Field Emissions(Above 1 ㎓)