2A9NX-S99Wireless Charger

FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. *RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

-HuizhouOJDTechnologyCo.,Ltd- FederalCommunicationsCommission AuthorizationandEvaluationDivision EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 4/8/24 U.S.AgentDesignation HuizhouOJDTechnologyCo.,Ltdacknowledgestheirconsentforthefollowingcontactlocatedinthe UnitedStatestoactastheiragentforserviceofprocessfortheequipmentforwhichauthorizationissought (FCCID:2A9NX-S99): NameandcompanyofU.S.agent: REPAmericaLLC PhysicalU.S.addressofagent:BenXU,6510SAcademyBlvd,SteA#523,ColoradoSprings,CO 80906 FRNofU.S.agent: 0034192500 EmailaddressofU.S.agent: [email protected] REPAmericaLLCacknowledgestheirobligationtoacceptserviceofprocessonbehalfofHuizhouOJD TechnologyCo.,Ltd. HuizhouOJDTechnologyCo.,LtdwiththeFRN0033155615acceptsitsobligationtomaintainanagent forserviceofprocessintheUnitedStatesfornolessthanoneyearaftereitherthegranteehaspermanently terminatedallmarketingandimportationoftheapplicableequipmentwithintheU.S.,ortheconclusionofany Commission-relatedadministrativeorjudicialproceedinginvolvingtheequipment,whicheverislater. Bysigningthisform,weconfirmtheaboveandthatweareawareoftheapplicationrequirementslistedunder§ 2.911(d)(7). TheinformationprovidedinthisletterisbasedonthereferencedrulepartsofTitle47oftheCFRaswellasKDB 986446D01. Anexpirationdateforthisletterdoesnotexist.IncasetheU.S.agentchanges,thegranteeisobligatedtonotify theFCCwithin30daysviathegrantingTCB. Sincerely, Signature HuaixiangPan generalmanager HuizhouOJDTechnologyCo.,Ltd Signature BenXU Manager REPAmericaLLC 4 8 _ [ m o d e l ] U S _ A g e n t _ 2 . 9 1 1 ( d ) ( 7 ) - U , V 0 5

Page 1 of 4 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. External Photos Photo 1 Photo 2 Page 2 of 4 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 4 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 4 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 ------End------

Label Size: L35mm * W35mm 1. The label is silk-screen on the sample Wireless Charger Model Name: S99 FCC ID: 2A9NX-S99 L W

Page 1 of 3 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Internal Photos Photo 1 Photo 2 Phone Antenna Watch Antenna Earphone Antenna Page 2 of 3 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 3 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 -----End------

Page 1 of 11 FCC ID: 2A9NX-S99 RF Exposure Evaluation 1 Measuring Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. According KDB680106 D01: KDB 680106 D01 Wireless Power Transfer v04. 2 Requirements According to the item 3 of KDB 680106 D01v04: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Mobile Device and Portable Device Configurations (2) Equipment Authorization Procedures for Devices Operating at Frequencies Below 4 MHz (3) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the top surface. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Page 2 of 11 FCC ID: 2A9NX-S99 3 Test Setup 4 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB 680106 D01 Wireless Power Transfer v04. Remark：The EUT’s test position A, B, C, D and E is valid for the E and H field measurements. Page 3 of 11 FCC ID: 2A9NX-S99 5 Equipment Approval Considerations The EUT does comply with KDB 680106 D01 as follow table. Requirements of section 5 of KDB 680106 D01 Yes / No Description Mobile Device and Portable Device Configurations Yes Mobile Device Equipment Authorization Procedures for Devices Operating at Frequencies Below 4 MHz Yse The device operate in the frequency range113-205KHz(for mobile phone & earphone) and 300-350KHz(for watch). RF Exposure compliance may be ensured only for a minimum separation distance that is greater than 20 cm, while use conditions at smaller distances can still be considered unlikely. Yes The EUT H-field strengths at 15 cm surrounding the device and 20 cm above the top surface. Page 4 of 11 FCC ID: 2A9NX-S99 6 Description of the test mode Equipment under test was operated during the measurement under the following conditions: Test Mode Description Mode 1 AC Adapter + EUT + Wireless charger receiver + Earphone + Watch wireless charger receiver Record Mode 2 AC Adapter + EUT + Wireless charger receiver + Earphone Pre-tested Mode 3 AC Adapter + EUT + Wireless charger receiver + Watch wireless charger receiver Pre-tested Mode 4 AC Adapter + EUT + Wireless charger receiver Pre-tested Mode 5 AC Adapter + EUT + Earphone + Watch wireless charger receiver Pre-tested Mode 6 AC Adapter + EUT + Earphone Pre-tested Mode 7 AC Adapter + EUT + Watch wireless charger receiver Pre-tested Mode 8 Test the EUT in idle mode. Pre-tested Note: 1. All test modes were pre-tested, but we only recorded the worst case in this report. 7 Peripheral List 8 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date (mm-dd-yy) Cal.Due date (mm-dd-yy) Electric and Magnetic Field Analyzer Narda EHP-200A 180ZX10505 21.06.2023 20.06.2024 No. Equipment Manufacturer Model No. Serial No. Power cord signal cable 1 Wireless charger receiver YBZ 15W N/A N/A N/A 2 Earphone PocBuds K6 N/A N/A N/A 3 Watch wireless charger receiver YBZ 5W N/A N/A N/A Page 5 of 11 FCC ID: 2A9NX-S99 9 Test Result Test Mode 1_MPE_Coil 1_Phone MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 1% Top 14.78 0.49 15cm ＜ 1% Top 14.96 0.35 15cm ＜ 1% Left 14.80 0.49 15cm ＜ 1% Right 14.72 0.50 15cm ＜ 1% Front 14.61 0.60 15cm ＜ 1% Rear 14.76 0.47 Limit 614 1.63 Margin Limit (%) 2.44% 36.81% MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 50% Top 14.11 0.49 15cm ＜ 50% Top 13.11 0.50 15cm ＜ 50% Left 13.89 0.58 15cm ＜ 50% Right 13.68 0.47 15cm ＜ 50% Front 13.99 0.40 15cm ＜ 50% Rear 13.55 0.43 Limit 614 1.63 Margin Limit (%) 2.30% 35.58% MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 99% Top 13.77 0.40 15cm ＜ 99% Top 12.67 0.46 15cm ＜ 99% Left 12.91 0.56 15cm ＜ 99% Right 13.28 0.46 15cm ＜ 99% Front 13.25 0.36 15cm ＜ 99% Rear 13.37 0.55 Limit 614 1.63 Margin Limit (%) 2.24% 34.36% Page 6 of 11 FCC ID: 2A9NX-S99 Test Mode 1_MPE_Coil 2_ Earphone MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 1% Top 13.99 0.28 15cm ＜ 1% Bottom 13.87 0.17 15cm ＜ 1% Left 14.01 0.12 15cm ＜ 1% Right 14.04 0.33 15cm ＜ 1% Front 13.99 0.39 15cm ＜ 1% Rear 14.29 0.16 Limit 614 1.63 Margin Limit (%) 2.33% 23.93% MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 50% Top 13.25 0.38 15cm ＜ 50% Bottom 12.68 0.42 15cm ＜ 50% Left 12.83 0.29 15cm ＜ 50% Right 12.56 0.26 15cm ＜ 50% Front 12.54 0.41 15cm ＜ 50% Rear 12.65 0.37 Limit 614 1.63 Margin Limit (%) 2.16% 25.77% MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 99% Top 12.90 0.16 15cm ＜ 99% Bottom 11.98 0.14 15cm ＜ 99% Left 12.30 0.16 15cm ＜ 99% Right 12.45 0.08 15cm ＜ 99% Front 12.11 0.06 15cm ＜ 99% Rear 12.36 0.21 Limit 614 1.63 Margin Limit (%) 2.10% 12.88% Page 7 of 11 FCC ID: 2A9NX-S99 Test Mode 1_MPE_Coil 3_ Watch MPE Test distance Battery levels Probe from EUT Side E-field (V/m) H-field (A/m) 20cm ＜ 1% Top 13.71 0.25 15cm ＜ 1% Bottom 13.83 0.26 15cm ＜ 1% Left 13.67 0.22 15cm ＜ 1% Right 13.94 0.34 15cm ＜ 1% Front 13.94 0.36 15cm ＜ 1% Rear 13.46 0.35 Limit 614 1.63 Margin Limit (%) 2.27% 22.09% MPE Test distance Battery levels Probe from E…

Text truncated - open the document above for the full version.

Page 1 of 25 Report No.: AITSZ24032006FW1 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. FCC TEST REPORT Client Information: Applicant: Huizhou OJD Technology Co., Ltd Applicant add.: 7F, Building 20, Zoina Hi-tech Industrial Park, No.6 Xinhua Avenue, Chenjiang Street, Zhongkai High-tech Zone, Huizhou city, Guangdong Province, China Manufacturer: Huizhou OJD Technology Co., Ltd Manufacturer add.: 7F, Building 20, Zoina Hi-tech Industrial Park, No.6 Xinhua Avenue, Chenjiang Street, Zhongkai High-tech Zone, Huizhou city, Guangdong Province, China Product Information: Product Name: Wireless Charger Model No.: S99 Brand Name: N/A FCC ID: 2A9NX-S99 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: Mar. 20, 2024 Date of Test: Mar. 20, 2024~ Apr. 08, 2024 Date of Issue: Apr. 08, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Sean She Eder Zhan Page 2 of 25 Report No.: AITSZ24032006FW1 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS .................................................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 5 2.1 STATEMENT OF THE MEASUREMENT UNCERTAINTY ......................................................................................... 5 2.2 MEASUREMENT UNCERTAINTY ...................................................................................................................... 5 3 TEST FACILITY .............................................................................................................................................. 6 3.1 DEVIATION FROM STANDARD ......................................................................................................................... 6 3.2 ABNORMALITIES FROM STANDARD CONDITIONS ............................................................................................... 6 3.3 TEST LOCATION .......................................................................................................................................... 6 4 GENERAL INFORMATION ............................................................................................................................. 7 4.1 EUT TEST MODE ........................................................................................................................................ 8 4.2 DESCRIPTION OF TEST SETUP ....................................................................................................................... 8 4.3 PERIPHERAL LIST ........................................................................................................................................ 9 4.4 EUT PERIPHERAL LIST ................................................................................................................................ 9 5 EQUIPMENTS LIST FOR ALL TEST ITEMS ................................................................................................. 10 6 CONDUCTED EMISSION TEST.................................................................................................................... 11 6.1 CONDUCTED EMISSION MEASUREMENT............................................................................................ 11 6.2 POWER LINE CONDUCTED EMISSION LIMITS ....................................................................................... 11 6.3 TEST PROCEDURE ............................................................................................................................... 11 6.4 DEVIATION FROM TEST STANDARD .................................................................................................... 11 6.5 TEST SETUP .......................................................................................................................................... 12 6.6 EUT OPERATING CONDITIONS ............................................................................................................ 12 6.7 TEST RESULT ........................................................................................................................................... 13 7 RADIATED EMISSION MEASUREMENT ..................................................................................................... 15 7.1 RADIATED EMISSION LIMITS ........................................................................................................................ 15 7.2 ANECHOIC CHAMBER TEST SETUP DIAGRAM ................................................................................................ 16 7.3 TEST PROCEDURE ......................................................................................................................…

Text truncated - open the document above for the full version.

Shenzhen Shenguang Electronic Technology Co.,LTD Client Huizhou OJD Electronic Technology Co.,LTD TYPE G43.5*5.3*0.8；Enamelled Wire 0.08*24p*2 , L=20MM Model NO SG-A1143.5-6.5UH Part nunbering SG-A1143.5-020-002 Client p/NO Enginrer NO TQE 1800510003 Date 2023-8-16 Operation frequency 113kHz-205kHz Antenna gain 0dBi Prepared Checked Approved XieYanQi DuanJiaWang XieXiaoZai For Enginer Departner Only Rrvised Content APProved Date Authorixed Signaturure Company Chop Enginrer QC APProved APProved Shenzhen Shenguang Electronic Technology Co.,LTD 一、 Winding Procese: NO Winding Wile Turns Direction Remarks 1 N1 2UEW-B-0.08*24P*2 10TS CCW 2 二．FEATURES: 1.Test conditions：25°C,65%RH@100KHz/1V 1.1 Inductance 1.11 L0A（Individual coil）=3.8uH±20% 1.12 L0A(Coil+Ferrite)=6.5uH±10% 1.2 Q=35MIN 1.3 DCR：85mΩ MAX 1.4 Operating Temperature：-25°C~85°C 2.Test instrument：L:CH1068+1310;DCR:502BC;SIZE:Callipers 3.Material List NO List Material 1 WIRE ￠0.08*24p*2 2UEW 2 FERRITE 43.5*5.3*0.8 L 3 GLUE White Glue 4 SOLDER XCD-907B 5 Adhesive / 6 High temperature adhesive 6MM ref 7 Shenzhen Shenguang Electronic Technology Co.,LTD 三．CIRCUIT DIAGRAM Unit： MM 四．OUTSIDE DIAGRA A B C D E I T H STD 43.5±0.5 39.0±1.5 5.3±0.5 20.5±0.5 2-5 0.8±0.15 2.6Max 20±2 Unit： MM Shenzhen Shenguang Electronic Technology Co.,LTD 五．PACKAGE 5.1 Packing Picture: 5.2 Packing Quantity Item Quantity Material Box 400 PCS 345*330*50 MM Big Carton 2000 PCS 360*340*280 MM 5.3 The packaging shall be based on the exusting packing plate and the actual delivery package shall prevail .If there is any requirement,we can customize it. Shenzhen Shenguang Electronic Technology Co.,LTD 六、 Storage and Use condition 6.1 Storage condition 6.1.1 Recommended keeping conditions: -25°C ~85°C, 70%RH (Max.) 6.1.2 Storage life : Within the limits of six months from being produced. 6.2 Use condition Use condition limit: T=-25°C~85°C, RH≤ 90%.

Shenzhen Shenguang Electronic Technology Co.,LTD Client Huizhou OJD Electronic Technology Co.,LTD TYPE A28 Double Coil +Stain L=90MM Model NO SG-A28-7.0UH Part nunbering SG-A28-090 Client p/NO Enginrer NO TQE 1800510003 Date 2023-8-16 Operation frequency 113kHz-205kHz Antenna gain 0dBi Prepared Checked Approved XieYanQi DuanJiaWang XieXiaoZai For Enginer Departner Only Rrvised Content APProved Date Authorixed Signaturure Company Chop Enginrer QC APProved APProved Shenzhen Shenguang Electronic Technology Co.,LTD 一、 Winding Procese: NO Winding Wile Turns Direction Remarks 1 N1 2UEW-B-0.08*105P 9TS CCW 2 二．FEATURES: 1.Test conditions：25°C,65%RH@100KHz/1V 1.1 Inductance 1.11 L0A（Individual coil）=4.1uH±20% 1.12 L0A(Coil+Ferrite)=Coil1=Coil2=7.0uH±10% 1.2 Q=70MIN 1.3 DCR：65mΩ MAX 1.4 Operating Temperature：-25°C~85°C 2.Test instrument：L:CH1068+1310;DCR:502BC;SIZE:Callipers 3.Material List NO List Material 1 WIRE ￠0.08*105p 2UEW-1.15mm 2 FERRITE 46.7*52*1.0*2 3 GLUE White Glue 4 SOLDER XCD-907B 5 Adhesive Double sided adhesive backing 6 High temperature adhesive 6MM Ref 7 Shenzhen Shenguang Electronic Technology Co.,LTD 三．CIRCUIT DIAGRAM Unit： MM 四．OUTSIDE DIAGRA Unit： MM 标准 A B C G H I T K1 K2 K3 K4 STD 94±1 52±1 2-5 5Ref 90±2 1.2Max 4.0Max 20±1 31±1 20±1 28±1 Shenzhen Shenguang Electronic Technology Co.,LTD 五．PACKAGE 5.1 Packing Picture: 5.2 Packing Quantity Item Quantity Material Box 180 PCS 345*330*50 MM Big Carton 720 PCS 360*340*280 MM 5.3 The packaging shall be based on the exusting packing plate and the actual delivery package shall prevail .If there is any requirement,we can customize it. Shenzhen Shenguang Electronic Technology Co.,LTD 六、 Storage and Use condition 6.1 Storage condition 6.1.1 Recommended keeping conditions: -25°C ~85°C, 70%RH (Max.) 6.1.2 Storage life : Within the limits of six months from being produced. 6.2 Use condition Use condition limit: T=-25°C~85°C, RH≤ 90%.

NOTE CUSTOMER'S Ĝ CONDITIONAL APPROVED REJECTED FULL APPROVED SIGNATURE PLEASE RETURN TO US COPY OF "SPECIFICATION FOR APPROVAL"WITH YOUR APPROVED SPECIFICATION FOR APPROVAL SIGNATURES. CUSTOMER P/N: : DATE KEFEITE NO.: KFT-107 A1 REV : SHENZHEN KEFEITE ELEECTRONICS CO.,LTD ROHS 1 / 5 ӗ૱ᅨਸ RoHSPAHS6PREACH FactoryAddress:2/F,Guantiancommunity,Shenzhen. FAX:86-755-27352742 TEL:86-755-27352660 New era industrial area HTTP:WWW.Kefeite.net CUSTOMER MODEL NO.: C Building 2023/09/08 27X8.1-10uH-13mm-01 107-27X8.1-0.06X65PX15TS-10uH-13mm-01 30800006-10.1uH Operation frequency: 300kHz-350kHz Antenna gain: 0dBi SHENZHEN KEFEITE ELECTRONICS CO.,LTD CUSTOMER: CUSTOMER NO: KFT P/N: VERSION A1 KFT-107 MODIFY THE CONTENT New Version VERSION: PAGE: Date: Date A1 2/4 Drawn By Checked By FIGO QIONJINFU NOTES: 2023/09/08 2023/09/08 107-27X8.1-0.06X65PX15TS-10uH-13mm-01 30800006-10.0uH 该文档是极速PDF编辑器生成， 如果想去掉该提示,请访问并下载： http://www.jisupdfeditor.com/ CUSTOMER: CUSTOMER NO: KFT P/N: 1.CONFIGURATION&DIMENSIONS: VERSION: PAGE: Date: 3/4 2.ElEETRICAL CHARACTER: PROJECT SPECFICTIONSTEST CONDITIONSTEST INSTRUMENT ˄/V &RLO ˄5'& 100KHZ/1.0V $Wć CH1062 HG2512 3.SCHEMATIC 4.PART NUMBERING:PRODUCT IDENTIFICATION s F DRAWN BY: CHECKED BY: Q.C DEPT: APPROVED BY: fX+ FI GO W.J.J KFT-107 İP¡ A1 2.Double sided adhesive tape on the back of the product SHENZHEN KEFEITE ELECTRONICS CO.,LTD QIONJINFU 2023/09/08 Serial number Inductance Line Length Wire Diameter Magnetic Sheet Specification Customer number 107 27X8.1 13mm 10uH 01 ˄/V &RLO&RUH100KHZ/1.0VCH1062fX+ 1.Magnet is installed in the center hole with the ʾ13ROHIDFLQJXSZDUGV [PPı*6 107-27X8.1-0.06X65PX15TS-10uH-13mm-01 30800006-10.0uH A B C D E F fPP fPP fPP fPP G ̚PP H fPP 6.0ref fPP J fPP K fPP I 3.6MAX 0.06X65PX15TS 该文档是极速PDF编辑器生成， 如果想去掉该提示,请访问并下载： http://www.jisupdfeditor.com/ CUSTOMER: CUSTOMER NO: KFT P/N: 5.MATERIAL LIST: VERSION: PAGE: Date: A1 4/4 DRAWN BY: CHECKED BY: Q.C DEPT: APPROVED BY: 6.GENERAL SPECIFICATION: KFT-107 SHENZHEN KEFEITE ELECTRONICS CO.,LTD FI GOW.J.JQIONJINFU 1 Tested at 1.0KHZ/0.25Vrms,0 Adc. $YHUDJHFXUUHQWIRUćWHPSHUDWXUHULVHIURPć 2 Saturaion current(Isat): Inductance drop:10% typ at Isat. 3 Heat rating current(Irms): /#,UPV Ƹ7İć (OHFWULFDOVSHFLILFDWLRQVDWć 6WRUDJH7HPSćć 2SHUDWLQJ7HPSćć 2023/09/08 NOITEMDESCRIPTIONRATINGSUPPLIERSUL NO. REMARK 1 2 3 4 WIRE SOLDER CORE EPOXY 99.3/0.7 ć SHANTOU SHENGANG ELECTRICAL E239508 INU\DUSTRIAL CO.,LTD SHENZHEN Hong Xing Wei solder Limited 1603HFR-HS DONGBU FINE CHEMICAL CO LTD 5 Acetone line 27/8.1/2.8 Changxing BO Cheng Electronics CO.,LTD Strong ; ̊*6 DONGBU FINE CHEMICAL CO LTD Magnet 107-27X8.1-0.06X65PX15TS-10uH-13mm-01 30800006-10.1uH 该文档是极速PDF编辑器生成， 如果想去掉该提示,请访问并下载： http://www.jisupdfeditor.com/

Page 1 of 2 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Test Setup Photo DCD Conduction Radiation (9KHz-30MHz) Page 2 of 2 FCC ID: 2A9NX-S99 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Radiation (30MHz-1000MHz) ------End------