2A9OKMQBRC7Cars123 Bubble RC

expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit Consult the dealer or an experienced radio/TV technici an for help. GUARDE ESTA INFORMAÇÃO PARA FUTURAS CONSULTAS. AS PIL HAS NÃO RECARREGÁVEI S NÃO DEVEM SER RECARREGADAS. AS PIL HAS RECARREGÁVEI S DEVEM SER REMOVIDAS DO PRODUTO ANTES DE SEREM RECARREGADAS. AS PIL HAS RECARREGÁVEI S SÓ DEVEM SER CARREGADAS SOB A SUPERVISÃO DE ADULTOS. NÃO SE DEVE MISTURAR PIL HAS NOVAS COM PIL HAS USADAS OU PIL HAS DE TIP OS DIF ERENTES. SÓ DEVEM SER USADAS AS PIL HAS RECOMENDADAS OU DE TIP O EQUIVAL ENTE. AS PIL HAS DEVEM SER COLOCADAS COM A POLARIDADE CERTA. AS PIL HAS FRACAS DEVEM SER RETIR ADAS DO APARELHO. OS TERMINAIS DE ALIMENTAÇÃO NÃO DEVEM ENTRAR EM REMOVA AS BATERIAS QUANDO NÃO ESTIVEREM EM USO OU QUANDO ESTIVEREM VAZIAS. RAADPLEGEN. WEGWERPBATTERIJEN DIENEN NIE T OPNIE UW OPGELADEN TE WORDEN. OPLAADBARE BATTERIJEN DIENEN VÓÓR HET OPLADEN UIT HET PRODUCT VERWIJDERD TE WORDEN. OPLAADBARE BATTERIJEN DIENEN ALLEEN ONDER TOEZICHT VAN EEN VOLWASSENE OPGELADEN TE WORDEN. GEBRUIK GEEN COMBINATIE VAN VERSCHIL LENDE SOORTEN BATTERIJEN OF NIE UWE EN GEBRUIKTE BATTERIJEN. GEBRUIK ALLEEN BATTERIJEN VAN HET AANBEVOLEN OF EEN OVEREENKOMSTIG SOORT. L ET BIJ HET PLAATSEN VAN BATTERIJEN OP DE JUISTE POLARITEI T. LEGE BATTERIJEN DIENEN UIT HET PRODUCT VERWIJDERD TE WORDEN. DE POLEN VAN DE BATTERIJEN NIE T KORTSLUITEN. VERWIJDER BATTERIJEN INDIEN NIE T IN GEBRUIK OF LEEG. CONSERVER CES INFORMATIONS POUR RÉFÉRENCE ULTÉRIE URE. NE PAS ESSAYER DE RECHARGER DES PIL ES NON RECHARGEABLES. ENLEVER LES PIL ES RECHARGEABLES DE L’APPAREIL AVANT DE LES CHARGER. CHARGER LES PIL E S RECHARGEABLES SOUS LA SURVEILLANCE D’UN ADULTE. NE PAS UTIL ISER ENSEMBLE DES PIL ES DE TYPES DIFFÉRENTS, NI DES PIL ES NEUVES AVEC DES PIL ES USAGÉES. UTIL ISER UNIQUEMENT DES PIL ES IDENTIQUES OU ÉQUIVALENTES À CELLES RECOMMANDÉES. INSÉRER LES PIL ES EN RESPECTANT LA POLARITÉ. ENLEVER LES PIL ES DE L’APPAREIL SI ELLES SONT USÉES. RETIR EZ LES PIL ES LORSQU’ELLES SONT DÉCHARGÉES OU GUARDAR ESTA INFORMACIÓN PARA FUTURAS CONSULTAS. LAS PIL AS NO RECARGABLES NO DEBEN RECARGARSE. LAS PIL AS RECARGABLES DEBEN SACARSE DEL PRODUCTO ANTES DE CARGARLAS. LAS PIL AS RECARGABLES DEBEN CARGARSE ÚNICAMENTE BAJO LA SUPERVISIÓN DE UN ADULTO. NO MEZCLAR PIL AS DE DISTINTOS TIP OS, NI PIL AS GASTADAS CON PIL AS NUEVAS. SÓLO SE DEBEN USAR PIL AS DEL TIP O RECOMENDADO U OTRO EQUIVALENTE. LAS PIL AS DEBEN COLOCARSE C ON LA POLARIDAD CORRECTA. LAS PIL AS AGOTADAS DEBEN SACARSE DEL JUGUETE. NO CORTOCIR CUITAR LOS BORNES DE LAS PIL AS. QUITE LAS BATERÍAS CUANDO NO SE ESTÉ USANDO O ESTÉN DESCARGADAS. CONSERVARE QUESTE INFORMAZIONI PER SUCCESSIVE CONSULTAZIONI. NON RICARICARE LE PIL E NON RICARICABIL I. RIMUOVERE LE PIL E RICARICABIL I DAL PRODOTTO PRIMA DI CARICARLO. LE PIL E RICARICABIL I DEVONO ESSERE CARICATE ESCLUSIVAMENTE SOTTO L A SUPERVISIONE DI UN ADULTO. NON USARE INSIE ME DIVERSI TIP I DI PIL E NÉ UTIL IZ ZARE INSIE ME PIL E VECCHIE E NUOVE. UTIL IZ ZARE SOLO PIL E DELLO STESSO TIP O O DI TIP O EQUIVALENTE A QUELLO RACCOMANDATO DAL PRODUTTORE. INSERIR E LE PIL E CON LA POLARITÀ CORRETTA. RIMUOVERE SEMPRE LE PIL E SCARICHE DAL PRODOTTO. I MORSETTI DI ALIMENTAZIONE NON DEVONO ESSERE CORTOCIR CUITATI. RIMUOVERE LE BATTERIE QUANDO NON IN USO O ESAU RITE. INFORMATIONEN FÜR ZUKÜNFTIGE ZWECKE AUFBEWAHREN. NICHT AUFLADBARE BATTERIEN NICHT AUFLADEN. AUFLADBARE BATTERIEN VOR AUFLADUNG VOM PRODUKT ENTFERNEN. AUFLADBARE BATTERIEN NUR UNTER AUFSICHT ERWACHSENER AUFLADEN. BATTERIEN NICHT GEMEINSAM EINSETZEN. AUSSCHLIE ßLICH EMPFOHLENE ODER GLEI CHWERTIGE BATTERIEN MIT DER KORREKTEN POLARITÄT EINSETZEN. LEERE BATTERIEN AUS DEM PRODUKT ENTFERNEN. KEINEN KURZSCHLUSS AN DEN ANSCHLUSSKLEMMEN VERURSACHEN. BATTERIEN IN ENTLADENEM ZUSTAND ODER BEI NICHTGEBRAUCH ENTFERNEN. GEM DISSE OPLYSNINGER TIL SENERE BRUG. GENOPLADELIGE BATTERIER SKAL TAGES UD AF PRODUKTET, FØR DE OPLADES. GENOPLADELIGE BATTERIER MÅ KUN OPLADES UNDER OPSYN AF EN VOKSEN. DER MÅ IK KE ANVENDES EN BLANDING AF FORSKELLIGE TYPER BATTERIER ELLER NYE OG BRUGTE BATTERIER. DET ANBEFALES KUN AT ANVENDE BATTERIER AF SAMME ELLER TIL SVARENDE TYPE. BATTERIERNE SKAL ISÆTTES MED DEN KORREKTE POLARITET. HELT AFLADEDE BATTERIER SKAL FJERNES FRA PRODUKTET. FORSYNIN GSPUNKTERNE MÅ IK KE KORTSLUTTES. TAG BATTERIERNE UD, NÅR ENHEDEN IK KE ER I BRUG ELLER ER AFLADET. SPARA DEN HÄR INFORMATIONEN FÖR FRAMTIDA BRUK. ICKE UPPLADDNINGSBARA BATTERIER FÅR INT LADDAS. TA UT UPPLADDNINGSBARA BATTERIER UR PRODUKTEN INNAN DE LADDAS. UPPLADDNINGSBARA BATTERIER FÅR ENDAST LADDAS UNDER UPPSIKT AV EN VUXEN. BLANDA INTE OLIK A TYPER AV BATTERIER ELLER NYA OCH GAMLA BATTERIER. ENDAST BATTERIER AV RE KOMMENDERAD TYP ELLER MOTSVARANDE FÅR ANVÄNDAS. BATTERIERNA MÅSTE SÄTTAS IN MED KORREKT POLA…

Text truncated - open the document above for the full version.

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 [LIGHTUPTOYS.COM LLC] Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to 47 CFR part §2.911(d)(7) of the FCC rules To whom it may concern, This letter is to certify that [LIGHTUPTOYS.COM LLC] (“Applicant”) accepts responsibilities to act as its own agent pursuant to 47 CFR part §2.911(d)(7) of the FCC rules for service of process. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated below. I [Andy Hong] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : Lightuptoys.com LLC Contact Name : Andy Hong Address : 8512 COMMERCE PARK DRIVE, SELLERSBURG, IN, US, 47172 Telephone No : 0755-27873952 Email : [email protected] FCC ID : 2A9OKMQBRC7 Applicant FRN : Signature: __ Date: Mar/30/2023 0033166307

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 [LIGHTUPTOYS.COM LLC] Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: [LIGHTUPTOYS.COM LLC] FCC ID: [2A9OKMQBRC & 2A9OKMQBRC7] To whom it may concern, [Lightuptoys.com LLC] (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant [is not] identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. ______________________________ [Signature of authorized Proprietor, Partner or Authorized Officer] [Andy Hong] [Director] [LIGHTUPTOYS.COM LLC] [Mar/14/2023]

APPENDIX B (LIGHTUPTOYS.COM LLC) [03/14/2023] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement (LIGHTUPTOYS.COM LLC) FCC ID: 2A9OKMQBRC7 To Whom It May Concern: We, LIGHTUPTOYS.COM LLC, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2A9OKMQBRC7 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (Mar/14/2023). The Limited Agency Agreement expires on (Mar/14/2024), unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] [Type Name] Andy Hong [Type Title] Director

<LIGHTUPTOYS.COM LLC> Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2A9OKMQBRC7 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate, and delete unselected parts] Schematics Block Diagrams Operational Description Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Sincerely, Andy Hong Director 14/03/2023

Page 1 of 2 External Photos Page 2 of 2

Label Artwork and Location

Page 1 of 3 Internal Photos Page 2 of 3 Page 3 of 3

1 INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is a Cars123 Bubble RC operating at 2.4G Band. The EUT can be powered by DC 4.5V (3 x 1.5V AAA batteries).For more detail information pls. refer to the user manual. Antenna Type: Integral antenna. Antenna Gain: 2.5dBi. The normal radiated output power (e.i.r.p) is: 0dBm (tolerance: +/- 3dB). The normal conducted output power is -2.5dBm (tolerance: +/- 3dB). Modulation Type: GFSK. According to the KDB 447498: The Maximum peak radiated emission for the EUT is 95.9 dBμV/m at 3m in the frequency 2469MHz The EIRP = [(FS*D) ^2 / 30] mW = 0.67dBm which is within the production variation. The Minimum peak radiated emission for the EUT is 95.4 dBμV/m at 3m in the frequency 2415MHz The EIRP = [(FS*D) ^2 / 30] mW = 0.17dBm which is within the production variation. The maximum conducted output power specified is 0.5dBm= 1.122mW The source- based time-averaging conducted output power =1.122mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.469) mW = 9.55 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: 2A9OKMQBRC7

LIGHTUPTOYS.COM LLC TEST REPORT SCOPE OF WORK FCC TESTING– MODEL:101Q123U144 REPORTNUMBER SZHH01766772-001 ISSUE DATE APR 3, 2023 PAGES 24 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.:SZHH01766772-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Service Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page:1 of 24 FCC ID 249_C Test Report LIGHTUPTOYS.COM LLC Application for Certification FCC ID: 2A9OKMQBRC7 Cars123 Bubble RC Model: 101Q123U144 2.4GHz Transceiver Report No.: SZHH01766772-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-21] Prepared and Checked by: Approved by: Sign on file Terry Tang Assistant Supervisor Ryan Chen Project Engineer Date: Apr 3, 2023 Intertek Report No.:SZHH01766772-001 Version: 01-November-2017 Page:2 of 24 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-21 Edition] provision. Report prepared by: Terry Tang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel / Fax: 86-755-86016288/86-755-86016751 Intertek Report No.:SZHH01766772-001 Version: 01-November-2017 Page:3 of 24 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ..................................................................................... 4 2.0 General Description ............................................................................................ 5 2.1Product Description ............................................................................................. 5 2.2Related Submittal(s) Grants ................................................................................ 5 2.3Test Methodology ................................................................................................ 5 2.4Test Facility ........................................................................................................ 5 3.0 System Test Configuration ................................................................................. 6 3.1 Justification ........................................................................................................ 6 3.2EUT Exercising Software ..................................................................................... 6 3.3Special Accessories ............................................................................................ 6 3.4Equipment Modification ....................................................................................... 6 3.5 Measurement Uncertainty .................................................................................. 6 3.6 Support Equipment List and Description ............................................................. 6 4.0Emission Results ................................................................................................. 7 4.1 Radiated Test Results ........................................................................................ 7 4.1.1 Field Strength Calculation ................................................................................ 7 4.1.2 Radiated Emission Configuration Photograph .................................................. 8 4.1.3Radiated Emissions .......................................................................................... 8 4.1.4 Transmitter Spurious Emissions .................................................................... 11 5.0 Equipment Photographs ................................................................................... 15 6.0Product Labelling ............................................................................................... 15 7.0Technical Specifications .................................................................................... 15 8.0Instruction Manual ............................................................................................. 15 9.0Miscellaneous Information ................................................................................ 16 9.1 Bandedge Plot ................................................................................................. 16 9.220dB Bandwidth ................................................................................................ 18 9.3Discussion of Pulse Desens…

Text truncated - open the document above for the full version.

Page 1 of 2 Radiated Photos Up to 1GHz (The EUT placed at the center of the turntable) Page 2 of 2 Above 1GHz (The EUT placed at the center of the turntable)