2A9QM-SSOLHB1sleepisol

IFU_HB1_R2.0E LeeSol 1 / 7 sleepisol Ⓡ User Manual IFU_HB1_R2.0E LeeSol 2 / 7 IFU_HB1_R2.0E LeeSol 3 / 7 IFU_HB1_R2.0E LeeSol 4 / 7 [Caution] Risk of fire or explosion if the battery is disposal into fire or hot oven, mechanically crushing or cutting [Caution] Risk of explosion or the leakage of flammable liquid or gas if the battery is leaving in an extremely high temperature surrounding environment. [Caution] Risk of explosion or the leakage of flammable liquid or gas if the battery is subjected to extremely low air pressure. IFU_HB1_R2.0E LeeSol 5 / 7 Specifications Product Name sleepisol Model Name HB-1 Description A healthcare device that helps brain health by transmitting microcurrents to the brain. Intended Use Wellness or healthcare device (non-medical device) Power Power: 5.0Vdc, 35mA Battery: 3.7V, 38mAh, Li-Poly RF Spec Bluetooth LE 1M (2402 ~ 2480 MHz) Max Power (E.I.R.P): Max 0.98 dBm (E.I.R.P) Operation Conditions Temperature: +5°C to +40°C Relative Humidity: 15% to 93% Atmospheric Pressure: 700~1060 hPa Storage and transportation conditions Temperature: -25°C to +70°C Relative Humidity: Less than 93% Atmospheric Pressure: 700~1060 hPa Warranty period 1 year Customer service Tel) +82-2-318-8890, Fax) +82-2-318-8842 E-mail) [email protected] Requirements CE This device can be operated in at least one Member state without infringing applicable requirements on the use of radio spectrum. FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. IFU_HB1_R2.0E LeeSol 6 / 7 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with RF exposure requirement. IFU_HB1_R2.0E LeeSol 7 / 7

Rev 1/26/2023 LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-26-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A9QM-SSOLHB1 [LeeSol Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Jiyoung Kim Rev 1/26/2023 LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-26-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A9QM-SSOLHB1 [LeeSol Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Jiyoung Kim

Certification designating a U.S. Agent for service of process: As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must: i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council: The Agent for Process of Service:  cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB)  cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab)  Agent can be Individual Entity or a Company Entity  Agent Entity must be located in US, US address/phone  Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter)  Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th A ve So uth, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Emai l: [email protected] FRN #: 0027533835 This l etter is to confirm that w e (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S . Agent for Serv ice of Pro cess as require d by sec tion 4 7 CFR 2.911(d)(7) on behalf of t he Applicant no ted below. U.S. Agent Signature: Date: July 27, 2023 Signed by (Printed Name/Title): Nathan Grin ager / Co-President *This letter is valid indefinitely for all applications submitted within the period of 07/27/2023 - 07/26/2024. The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: LeeSol Co., Ltd. FCC ID: 2A9QM-SSOLHB1 Contact Name: Jiyoung Kim Street Address: 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 City/Province/Zip:- Telephone No: +82-2-318-8890 Email: [email protected] Applicant Signature: Date: 07/26/2023 Signed by (Printed Name/Title): Jiyoung Kim / Manager

LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 Date: 07/27/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Declaration Letter FCC ID: 2A9QM-SSOLHB1 To Whom It May Concern: This device is integrated with the certified module.( FCC ID: 2A5XQ-POT-NR232) When the authorized module is built into the final product, there are no changes in the hardware. Approval module report was submitted when it apply for a certification. The original module test report accurately represents antenna-port conducted test results under the host application(FCC ID: 2A9QM-SSOLHB1). Sincerely, Contact Name: Jiyoung Kim Title: Manager

LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 Date: 07/27/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Request of Confidentiality FCC ID: 2A9QM-SSOLHB1 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LeeSol Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LeeSol Co., Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Schematics 3 Part Lists 4 Operation Description 5 NA SHORT-TERM 6 Internal Photos 7 External Photos 8 Test-Setup Photos 9 User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Contact Name: Jiyoung Kim Title: Manager

LeeSol Co., Ltd. 3F, 3 Duteopbawi-ro 1-gil, Yongsan-gu Seoul South Korea 04334 Date: 07/27/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Letter of Authorization We, the undersigned, hereby authorize Geunki Son of Dt&C Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: 2A9QM-SSOLHB1 including signing of all documents relating to these matters. Any and all acts carried out by Geunki Son of Dt&C Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LeeSol Co., Ltd.. “I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a).” Sincerely, Contact Name: Jiyoung Kim Title: Manager

FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 1 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 2 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 3 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 4

FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 1 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 2 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 3 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 4 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 5 FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. View 6 <Antenna>

FCC ID: RF feature Mode Transmitting Frequency(MHz) Test separation distance (mm) ANT Gain (dBi) Max. power with tune-up tolerance (dBm) Note1 Max. power with tune-up tolerance (mW) Power thresholds SAR test exclusion thresholds BLE 1 Mbps 2 480.00 5.0 0.50 0.87 1.221 8 0.38 3.00 Note1. Conclusion : = [ ( 1.2218mW / 5mm ) ] X [ √2.48GHz ] = 0.38Note. The calculation result was rounded to two decimal place f or comparison. 2A9QM-SSOLHB1 Please refet to the operation description for Max Tune-up power . Standalone SAR test exclusion considerations SAR evaluation for general popul ation exposure conditions by me asurement or numerical simulation is not required KDB 447498 D01 clause 4.3.1 Step 1) SAR test exclusion thresho lds for 100MHz to 6GHz at test separation distances ≤ 50 mm [ ( max. power of channel, inclu ding tune-up tolerance, mW ) / ( min. test separation distance, mm ) ] · [ √f(GHz) ] ≤ 3.0 for 1g SAR and ≤ 7.5 for 10g extremity SAR Sample Calculation

Report No.: DRTFCC2307-0106 FCC ID: 2A9QM-SSOLHB1 This test report is prohibited to copy or reissue in whole or in part without the approval of Dt&C Co., Ltd. TRF-RF-238(06)210316 Pages: 2 / 21 Test Report Version Test Report No. Date Description Revised by Reviewed by DRTFCC2307-0106 Jul, 26. 2023 Initial issue SeungMin Gil JaeJin Lee Report No.: DRTFCC2307-0106 FCC ID: 2A9QM-SSOLHB1 This test report is prohibited to copy or reissue in whole or in part without the approval of Dt&C Co., Ltd. TRF-RF-238(06)210316 Pages: 3 / 21 Table of Contents 1. General Information .................................................................................... 4 1.1. Description of EUT .......................................................................................................... 4 1.2. Declaration by the applicant / manufacturer ................................................................ 4 1.3. Testing Laboratory .......................................................................................................... 5 1.4. Testing Environment ....................................................................................................... 5 1.5. Measurement Uncertainty............................................................................................... 5 1.6. Test Equipment List ........................................................................................................ 6 2. Test Methodology ........................................................................................ 7 2.1. EUT Configuration ........................................................................................................... 7 2.2. EUT Exercise .................................................................................................................... 7 2.3. General Test Procedures ................................................................................................ 7 2.4. Instrument Calibration .................................................................................................... 7 2.5. Description of Test Modes.............................................................................................. 7 3. Antenna Requirements ............................................................................... 8 4. Summary of Test Results ........................................................................... 9 5. Test Result ................................................................................................. 10 5.1. Unwanted Emissions (Radiated) .................................................................................. 10 5.1.1. Test Setup .................................................................................................................. 11 5.1.2. Test Procedures ........................................................................................................ 11 5.1.3. Test Results ............................................................................................................... 12 5.2. AC Power-Line Conducted Emissions ........................................................................ 14 5.2.1. Test Setup .................................................................................................................. 14 5.2.2. Test Procedures ........................................................................................................ 14 5.2.3. Test Results ............................................................................................................... 14 APPENDIX I .................................................................................................... 17 APPENDIX II ................................................................................................... 18 APPENDIX III .................................................................................................. 19 Report No.: DRTFCC2307-0106 FCC ID: 2A9QM-SSOLHB1 This test report is prohibited to copy or reissue in whole or in part without the approval of Dt&C Co., Ltd. TRF-RF-238(06)210316 Pages: 4 / 21 1. General Information 1.1. Description of EUT Equipment Class Digital Transmission System (DTS) Product Name sleepisol Model Name HB-1 Add Model Name HB-1-BB, HB-1-SW Firmware Version Identification Number 6 EUT Serial Number No Specified Power Supply DC 3.7 V Frequency Range 2 402 MHz ~ 2 480 MHz Modulation Technique (Data rate) GFSK (1Mbps) Antenna Specification Antenna Type: Chip Antenna Gain: 0.50 dBi (PK) 1.2. Declaration by the applicant / manufacturer N/A Report No.: DRTFCC2307-0106 FCC ID: 2A9QM-SSOLHB1 This test report is prohibited to copy or reissue in whole or in part without the approval of Dt&C Co., Ltd. TRF-RF-238(06)210316 Pages: 5 / 21 1.3. Testing Laboratory Dt&C Co., Ltd. The 3 m test site and conducted measurement facility used to collect the radiated data are located at the 42, Yurim-ro, 154beon-gil, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 17042. The test site complies with the requirements of Part 2.948 according to ANSI C63.4-2014. - FCC & IC MRA Designation No. : KR0034 - ISED#: 5740A www.dtnc.net Telephone : + 82-31-321-2664 FAX : + 82-31-321-1664 1.4. Testing Environment Ambient Condition ▪ Temperature +21 °C ~ +24 °C ▪ Relative Humidity +49 % ~ +54 % 1.5. Measurement Uncertainty The measurement uncertainties shown below were calculated in accordance with requirements of ANSI C63.4-2014 and ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95 % level of confidence. Parameter Measurement uncertainty Antenna-port conducted emission 1.1 dB (The confidence level is about 95 %, k = 2) AC power-line conducted emission 3.4 dB (The confidence level is about 95 %, k = 2) Radiated emission (1 GHz Below) 4.8 dB (The confidence level is about 95 %, k = 2) Radiated emission (1 GHz ~ 18 GHz) 5.0 dB (The confidence level is about 95 %, k = 2) Radiated emission (18 GHz Above) 5.2 dB (The confid…

Text truncated - open the document above for the full version.

2450 MHz AntennaP/N 2450AT18B100 Detail Specification: 03/08/2016 Page 1 of 4 Mechanical Dimensions Inmm L±± W±± T a±± Mount these devices with brown mark facing up. Units: mm Line width should be designed to provide 50 Ω impedance matching characteristics. a) Without Matching Circuits b) With Matching Circuits Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Ver.2.1 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2016 Johanson Technology, Inc. All Rights Reserved NC Termination style 100% Tin 0.020 1.30 0.30 Tin / LeadPlease consult Factory 1.600.200.008 Feeding Point 2 Suffix = None Mounting Considerations Terminal Configuration No. 1 Function 0.012 0.051+.004/-.008+0.1/-0.2 Part Number Explanation BulkSuffix = SEg. 2450AT18B100S T & RSuffix = EEg. 2450AT18B100E Packaging Style P/N Suffix Eg. 2450AT18B100(E or S) General Specifications Input Power Impedance Operating Temperature Reel Quanity Peak Gain Average Gain-0.5 dBi typ. (XZ-V) 9.5 dB min. Part Number Frequency Range 2W max. 50 Ω -45°C to 125°C 3,000 Return Loss "High Frequency Ceramic Solutions" 0.50 0.1260.0083.200.20 0.063 2450AT18B100 2400 - 2500 Mhz 0.5 dBi typ. (XZ-V) 1 2 L W a T ) Matching Component JTI P/Ns: L-14C2N7JV4 L-14C2N2JV4 * 2.6 4.2 1.6 1.9 0.4 2.7nH 1.2pF 3.3nH JTI P/N for Matching Circuit: Cap (1.2pF): 500R07S1R2BV4T Inductor (2.7nH): L-07C2N7SV6T Inductor (3.3nH): L-07C3N3SV6T 2450 MHz AntennaP/N 2450AT18B100 Detail Specification: 03/08/2016 Page 2 of 4 Test Board: Return Loss a) Without Matching Circuitb) With Matching Circuit Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Ver.2.1 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2016 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" Typical Electrical Characteristics (T=25 o C) ) ) ) ) ) ) ) ) ) Ground 13.5mm 6.5mm 39.5mm 6.5mm Matching Circuit No Ground 50 Feed Line Antenna 19mm 4mm 2450 MHz AntennaP/N 2450AT18B100 Detail Specification: 03/08/2016 Page 3 of 4 Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Ver.2.1 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2016 Johanson Technology, Inc. All Rights Reserved "High Frequency Ceramic Solutions" Typical Radiation Patterns at 2.45GHz (+25C) ) ) ) ) ) ) ) ) ) 2450 MHz AntennaP/N 2450AT18B100 Detail Specification: 03/08/2016 Page 4 of 4 Would you like Johanson Technology's RF team to help you design and tune our antenna on your board? Click on the link below: Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. Ver.2.1 www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2016 Johanson Technology, Inc. All Rights Reserved www.johansontechnology.com/recommended-storage-conditions www.johansontechnology.com/tape-reel-packaging Soldering Information www.johansontechnology.com/typical-soldering-profile RoHS Compliance www.johansontechnology.com/rohs-compliance MSL Info "High Frequency Ceramic Solutions" Antenna layout review, tuning, and characterization services http://www.johansontechnology.com/ipc-antenna-services Packaging information www.johansontechnology.com/msl-rating.html Recommneded Storage Condition and Max Shelf Life ) ) ) ) ) ) ) ) )

Page 1 of 35 Report No.: OT-223-RWD-083 This Report is not correlated with the authentication of KOLAS It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) RADIO PERFORMANCE TEST REPORT Test Report No. : OT-223-RWD-083 Reception No. : 2202000536 Applicant : PROCHIP Address : #1112, Ace High-End Tower 1st, 5, Digital-Ro 26, Guro-Gu, Seoul, KOREA Manufacturer : PROCHIP Address : #1112, Ace High-End Tower 1st, 5, Digital-Ro 26, Guro-Gu, Seoul, KOREA Type of Equipment : BLE module FCC ID. : 2A5XQ-POT-NR232 Model Name : PoT-nR232 Multiple Model Name : N/A Serial number : N/A Total page of Report : 35 pages (including this page) Date of Incoming : March 02, 2022 Date of issue : March 31, 2022 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Tested by Joon-Woo, Kim / Assistant Manager ONETECH Corp. Reviewed by Tae-Ho, Kim / General Manager ONETECH Corp. Approved by Ki-Hong, Nam / General Manager ONETECH Corp. Page 2 of 35 Report No.: OT-223-RWD-083 This Report is not correlated with the authentication of KOLAS It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 5 2. TEST SUMMARY .............................................................................................................................................................. 6 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 6 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 6 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 6 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 6 2.5 TEST METHODOLOGY .................................................................................................................................................... 6 2.6 TEST FACILITY ............................................................................................................................................................... 6 3. GENERAL INFORMATION ............................................................................................................................................ 7 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 7 4. EUT MODIFICATIONS .................................................................................................................................................... 7 5. SYSTEM TEST CONFIGURATION ............................................................................................................................... 8 5.1 JUSTIFICATION ............................................................................................................................................................... 8 5.2 PERIPHERAL EQUIPMENT .............................................................................................................................................. 8 5.3 MODE OF OPERATION DURING THE TEST ...................................................................................................................... 8 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................. 10 6. PRELIMINARY TEST .................................................................................................................................................... 10 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ....................................................................................................... 10 6.2 GENERAL RADIATED EMISSIONS TESTS ..................................................................................................................... 10 7. MINIMUM 6 DB BANDWIDTH .................................................................................................................................... 11 7.1 OPERATING ENVIRONMENT ......................................................................................................................................... 11 7.2 TEST SET-UP ................................................................................................................................................................. 11 7.3 TEST DATE ................................................................................................................................................................... 11 7.4 TEST DATA FOR 1 MBPS ............................................................................................................................................... 12 8. MAXIMUM PEAK OUTPUT POWER .........................................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. Test Setup photographs EUT Position: X-axis EUT Position: Y-axis EUT Position: Z-axis FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. Test Setup Photo of Radiated Measurement (0.009 ~ 30MHz) FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. Test Setup Photo of Radiated Measurement (Below 1GHz) FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. Test Setup Photo of Radiated Measurement (Above 1GHz) FCC ID: 2A9QM-SSOLHB1 Copyright Ⓒ 2023, Dt&C Co., Ltd. Test Setup Photo of AC Line Conducted Measurement