2A9TS-BSN-MMNIndustrial wireless remote controller

Remote control instruction manual 1. Overview of the remote control Remote control transmitter is through the transmission of a certain frequency of high frequency signal, the signal is received by the remote control receiver, converted into other signals, so as to achieve the control of various functions of the controlled equipment. 2. Basic parameters of transmitter a) Supply voltage: DC 7.4V (powered by two lithium batteries in series) b) Maximum working current: ≤ 300mA; c) Battery: maximum open circuit voltage 8.4V, continuous working time ≥8h. 3. Main technical indicators of transmitter a) Working mode: wireless half-duplex transmission; b) Center operating frequency: 433MHz; c) Transmitted power: -20 to 10 dBm; d) Remote control distance: ≥20m. 4. Remote control instructions Figure 1 Transmitter a) As shown in the picture above, install the battery, pull up the emergency stop on the side of the transmitter, the "Start" button is set in the upper right corner of the remote control panel of the transmitter, press the "Start" button, the transmitter is activated, trying to establish communication with the receiver, the red "signal indicator" stroboscope once a second. b) When the communication is established, the receiver's "power/communication" indicator light will stroboscope once a second, operate the side button on the transmitter, shake the head switch or rocker, the transmitter's "signal indicator light" stroboscope 3 times a second, indicating that the corresponding control code signal has been issued, at this time the receiver's "function" indicator light will stroboscope 3 times a second, The CAN signal line of the receiver will send out the corresponding control code signal. c) After shooting the "emergency stop" switch of the transmitter, the "emergency stop/failure" indicator light of the receiver will flash red and blue alternately and output signal action. FIG. 2 Receiver 5. How the receiver works a) Radio receiving board: high-frequency signals from the wireless transmitter are received by the receiving board and then become serial data signals. b) After the serial data from the radio receiving board is processed by the single chip microcomputer, the received working states are controlled (such as sending out CAN data, relay action). 6. Basic parameters of receiver a) Supply voltage: DC12-32V; b) Maximum working current: ≤ 500mA; 7. Main technical indicators of the receiver a) Antenna impedance: 50Ω; b) Working mode: wireless half duplex reception; c) Center operating frequency: 433MHz; d) Remote control distance: ≥20m; FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Sincerely, Name/Title： Lei Yu/Electronic Engineer Company: Shanghai Ganite Control Technology Co., Ltd Address: Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Phone: 021-58558148 Fax: 021-58558148 E-Mail: [email protected]

Page 1 of 4 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity External Photos of the EUT Fig. 1 Fig. 2 Page 2 of 4 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 Page 3 of 4 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 4 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8

Page 1 of 1 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity LABEL AND LOCATION (Size: L3.0cm x 3.0cm) Label Location Industrial wireless remote controller Model: BSN-MMN (SY5-C) FCC ID: 2A9TS-BSN-MMN

Page 1 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Internal Photos of the EUT Fig. 1 Fig. 2 Page 2 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 3 Fig. 4 TX Antenna Page 3 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 5 Fig. 6 Page 4 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 7 Fig. 8 Page 5 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 9 Fig. 10 Page 6 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 11 Fig. 12 Page 7 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 13 Fig. 14 Page 8 of 8 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Fig. 15 Fig. 16

Manufacturer：Shanghai Ganite Control Technology Co., Ltd Modle: BSN-MMN (SY5-C) 433MHz Operation frequency：433.92MHz Antenna Gain：0dBi (Max) L W :1.7cmx0.5cm

Page 1 of 27 FCC ID: 2A9TS-BSN-MMN Report No.: LCSA121922067EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT For Shanghai Ganite Control Technology Co., Ltd Industrial wireless remote controller Test Model: BSN-MMN (SY5-C) Additional Model No.: Please Refer to Page 6 Prepared for : Shanghai Ganite Control Technology Co., Ltd Address : Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : December 20, 2022 Number of tested samples : 2 Sample number : A121922067-1, A121922067-2 Serial number : Prototype Date of Test : December 20, 2022 ~ December 30, 2022 Date of Report : January 03, 2023 Page 2 of 27 FCC ID: 2A9TS-BSN-MMN Report No.: LCSA121922067EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC TEST REPORT FCC CFR 47 PART 15 C(15.231) Report Reference No. .............. : LCSA121922067EA Date of Issue ............................... : January 03, 2023 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ...................................... : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Testing Location/ Procedure ....... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ...................... : Shanghai Ganite Control Technology Co., Ltd Address ...................................... : Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Test Specification Standard ..................................... : FCC CFR 47 PART 15 Subpart C, ANSI C63.10-2013 Test Report Form No. ............... : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : Industrial wireless remote controller Trade Mark ................................. : TECHWELL Test Model .................................. : BSN-MMN (SY5-C) Ratings ....................................... : DC 7.4V by Rechargeable Battery, 3000mAh Result ....................................... : Positive Compiled by: Supervised by: Approved by: Kay Hu/ Administrator Cary Luo/ Technique principal Gavin Liang/ Manager Page 3 of 27 FCC ID: 2A9TS-BSN-MMN Report No.: LCSA121922067EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity FCC -- TEST REPORT EUT......................................... : Industrial wireless remote controller Test Model........................... : BSN-MMN (SY5-C) Applicant............................... : Shanghai Ganite Control Technology Co., Ltd Address.................................. : Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Telephone............................... : / Fax.......................................... : / Manufacturer....................... : Shanghai Ganite Control Technology Co., Ltd Address................................... : Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Telephone............................... : / Fax.......................................... : / Factory....................... : Shanghai Ganite Control Technology Co., Ltd Address................................... : Floor 1, Room 102, No. 29, Lane 188, Maoting Road, Chedun Town, Songjiang District, Shanghai, China Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCSA121922067EA January 03, 2023 Date of issue Page 4 of 27 FCC ID: 2A9TS-BSN-MMN Report No.: LCSA121922067EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Revision History Report Version Issue Date Revision Content Revised By 000 January 03, 2023 Initial Issue -- Page 5 of 27 FCC ID: 2A9TS-BSN-MMN Report No.: LCSA121922067EA Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bld…

Text truncated - open the document above for the full version.

Page 1 of 1 FCC ID: 2A9TS-BSN-MMN Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity Test Setup Photos of the EUT Test Setup Photo(s) of Radiated Emissions Measurement Fig. 1 Fig. 2