2AA4AW002Adult pleasure object

Important Statements: This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Robotime Technology (Suzhou) Co., Ltd. Room 607, Building A, 5# XingHan Road, Suzhou Request for Confidentiality Date: 2013-09-28 _ Subject: Confidentiality Request for: FCC ID:2AA4AW002__ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ Robotime Technology (Suzhou) Co., Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. By: _Engineer_________________ _________lily.hong_ ______________ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 1 of 6 Page 1 of 6 Amanda-W002_External Photos Application No.: SHEM1309001873RF Applicant: Robotime Technology (Suzhou) Co., Ltd. Address of Applicant: Room 607, Building A, 5# XingHan Road, Suzhou Equipment Under Test (EUT): Product Name: Adult pleasure object Brand Name: EFEELINK Model No.: Amanda-W002 Add Model No.: N/A FCC ID: 2AA4AW002 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 2 of 6 Page 2 of 6 1 Contents Page 1 CONTENTS.......................................................................................................... 2 2 EXTERNAL PHOTOS ........................................................................................ 3 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 3 of 6 Page 3 of 6 2 External Photos SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 4 of 6 Page 4 of 6 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 5 of 6 Page 5 of 6 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix A Page: 6 of 6 Page 6 of 6 End

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 1 of 7 Page 1 of 7 Amanda-W002_Internal Photos Application No.: SHEM1309001873RF Applicant: Robotime Technology (Suzhou) Co., Ltd. Address of Applicant: Room 607, Building A, 5# XingHan Road, Suzhou Equipment Under Test (EUT): Product Name: Adult pleasure object Brand Name: EFEELINK Model No.: Amanda-W002 Add Model No.: N/A FCC ID: 2AA4AW002 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 2 of 7 Page 2 of 7 1 Contents Page 1 CONTENTS.......................................................................................................... 2 2 INTERNAL PHOTOS ......................................................................................... 3 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 3 of 7 Page 3 of 7 2 Internal Photos SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 4 of 7 Page 4 of 7 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 5 of 7 Page 5 of 7 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 6 of 7 Page 6 of 7 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix B Page: 7 of 7 Page 7 of 7 E EE En nn nd dd d

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 [email protected] Report No.: SHEM130900187303 Page: 1 of 9 Tony Wu E&E Section Manager SGS-CSTC (Shanghai) Co., Ltd. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page FCC MPE REPORT Application No.: SHEM1309001873RF Applicant: Robotime Technology (Suzhou) Co., Ltd. Manufacturer: Not supplied by the client. Factory: Not supplied by the client. FCC ID: 2AA4AW002 Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Adult pleasure object Model No.(EUT): Amanda-W002 Brand Name: EFEELINK Standards: FCC Rules 47 CFR §2.1093 KDB 447498D01 General RF Exposure Guidance v05 Date of Receipt: September 24, 2013 Date of Test: September 25, 2013 to September 28, 2013 Date of Issue: October 09, 2013 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130900187303 Page: 2 of 9 2 Version Revision Record Version Chapter Date Modifier Remark 00 / October 09, 2013 / Original Authorized for issue by: Engineer Eddy Zong Print Name Clerk Susie Liu Print Name Reviewer Keny Xu Print Name SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130900187303 Page: 3 of 9 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE .............................................................................................................. 1 1 COVER PAGE ............................................................................................................................ 1 2 VERSION ..................................................................................................................................... 2 3 CONTENTS ................................................................................................................................. 3 4 GENERAL INFORMATION ...................................................................................................... 4 4.1 CLIENT INFORMATION ............................................................................................................ 4 4.2 GENERAL DESCRIPTION OF E.U.T. ......................................................................................... 4 4.3 TECHNICAL SPECIFICATIONS: ................................................................................................. 4 4.4 ACCESSORIES OF PRODUCT: ................................................................................................... 4 4.5 TEST LOCATION ...................................................................................................................... 5 4.6 TEST FACILITY ....................................................................................................................... 5 5 RF EXPOSURE COMPLIANCE REQUIREMENT ......................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 [email protected] Report No.: SHEM130900187302 Page: 1 of 74 Tony Wu E&E Section Manager SGS-CSTC (Shanghai) Co., Ltd. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page FCC Part 15C TEST REPORT Application No.: SHEM1309001873RF Applicant: Robotime Technology (Suzhou) Co., Ltd. Manufacturer: Not supplied by the client. Factory: Not supplied by the client. FCC ID: 2AA4AW002 Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Adult pleasure object Model No.(EUT): Amanda-W002 Brand Name: EFEELINK Standards: FCC PART 15 SUBPART C, Section 15.247:2012 Date of Receipt: September 24, 2013 Date of Test: September 25, 2013 to September 28, 2013 Date of Issue: October 09, 2013 Test Result: Pass* *In the configuration tested, the EUT detailed in this report complied with the standards specified above. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130900187302 Page: 2 of 74 2 Version Revision Record Version Chapter Date Modifier Remark 00 / October 09, 2013 / Original Authorized for issue by: Engineer Eddy Zong Print Name Clerk Susie Liu Print Name Reviewer Keny Xu Print Name SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130900187302 Page: 3 of 74 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement FCC Part 15, Subpart C Section 15.203/15.247 (c) --- PASS AC Power Line Conducted Emission FCC Part 15, Subpart C Section 15.207 ANSI C63.10 (2009) Section 6.2 PASS 20dB Occupied Bandwidth FCC Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2009) Section 6.9.1 PASS Conducted Peak Output Power FCC Part 15, Subpart C Section 15.247 (b)(1) ANSI C63.10 (2009) Section 6.10.1 PASS Carrier Frequencies Separation FCC Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2009) Section 7.7.2 PASS Hopping Channel Number FCC Part 15, Subpart C Section 15.247 (b) ANSI C63.10 (2009) Section 7.7.3 PASS Dwell Time FCC Part 15, Subpart C Section 15.247 (a)(1) ANSI C63.10 (2009) Section 7.7.4 PASS RF Conducted Spurious Emissions FCC Part 15, Subpart C Section 15.247(d) ANSI C63.10 (2009) Section 7.7.10 PASS Radiated Spurious Emissions and Band-edge FCC Part 15, Subpart C Section 15.209 and Section 15.205 ANSI C63.10 (2009) Section 6.12 PASS SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130900187302 Page: 4 of 74 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any h…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix C Page: 1 of 4 Page 1 of 4 Amanda-W002_Part 15C Test Setup Photos Application No.: SHEM1309001873RF Applicant: Robotime Technology (Suzhou) Co., Ltd. Address of Applicant: Room 607, Building A, 5# XingHan Road, Suzhou Equipment Under Test (EUT): Product Name: Adult pleasure object Brand Name: EFEELINK Model No.: Amanda-W002 Add Model No.: N/A FCC ID: 2AA4AW002 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix C Page: 2 of 4 Page 2 of 4 1 Contents Page 1 CONTENTS............................................................................................................... 2 2 EQUIPMENT UNDER TEST PICTURES ............................................................. 3 2.1 Radiated Emission Test Setup .......................................................................... 3 2.2 Conducted Emission Test Setup ....................................................................... 4 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix C Page: 3 of 4 Page 3 of 4 2 EQUIPMENT UNDER TEST PICTURES 2.1 Radiated Emission Test Setup 30MHz-1GHz Above 1GHz SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1309001873RF －Appendix C Page: 4 of 4 Page 4 of 4 2.2 Conducted Emission Test Setup End