2AA5H-AP001V2Active Fall Detection Pendant

User Manual ActivePERS Active Personal Emergency Response System Model Number: AP001V2 Introduction ActivePERS is a personal emergency response pendant with patented and clinically validated automatic fall detection algorithms developed by BioSensics LLC. The key features and benefits of the ActivePERS technology include detecting falls with clinically validated and patented algorithms that virtually eliminate false alarms, monitoring the number of steps taken, and notifying providers when the pendant is not worn by the subscriber. This manual describes basic features of ActivePERS AP001V2. Detecting a Fall In the case of a fall detected automatically, the LED will turn on, and a fall alert message will be transmitted. Sending Heartbeat Messages AP001V2 sends heartbeat messages every hour. These messages contain the accumulated activity information, with values determined by the number of steps. Sending Panic Signal To send a panic signal, press and release the button. The LED should turn on upon release, and a message will be transmitted to indicate the panic. Clearing Alarm To clear an alarm and turn off the LED, press and hold the button until the LED turns off, which will take approximately 10 seconds. This will transmit a clear alarm message. The LED will turn on and remain on after sending a fall or a panic signal. Sending a clear alarm signal will turn the LED off. Specifications  Dimension: 2.165” x 1.468” x 0.603”  RF Transmission Frequency: 345 MHz  Operating Temperature: -10ºC to 60ºC  Battery Type: CR2450 Lithium  Battery Life: 1 year  Battery Voltage: 3.0V  FCC ID: 2AA5H-AP001V2 FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: Changes or modifications not expressly approved by BioSensics LLC could void the user’s authority to operate this equipment. Battery Warning This product contains a lithium battery. Lithium batteries can explode, leak, catch fire or cause burns if not handled appropriately. Do not disassemble, puncture or crush battery. Avoid exposure to water, fire or high temperatures. Properly dispose of battery.

678 Massachusetts Ave. Unit 904 , Cambridge, Massachusetts, 02139, United States TEL: +18885896213 FAX: +18885896213 Date: 2014-11-21 FCC ID: 2AA5H-AP001V2 A U T H O R I Z A T I O N L E T T E R To whom it may concern: I, the undersigned Ashkan Vaziri of BioSensics hereby authorize Rob Gonsiewski of BioSensics to act on my behalf in all matters relating to all processes required in FCC and any communication needed with the national authority. Any and all acts carried out by Rob Gonsiewski on my behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ----------------------------------- Name: Ashkan Vaziri / Title: Co-Founder BioSensics LLC TEL: +18885896213 FAX: +18885896213 E-mail: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT

Page 2 Page 3 Page 4

Report No.: RF141002C01 1 of 23 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF141002C01 MODEL NO.: AP001V2 FCC ID : 2AA5H-AP001V2 RECEIVED: Oct. 02, 2014 TESTED: Oct. 23 ~ Oct. 24, 2014 ISSUED: Nov. 03, 2014 APPLICANT : BioSensics LLC ADDRESS : 678 Massachusetts Ave. Unit 904, Cambridge, MA 02139, USA ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION : No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF141002C01 2 of 23 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................................. 3 1 CERTIFICATION ........................................................................................................................ 4 2 SUMMARY OF TEST RESULTS ............................................................................................... 5 2.1 MEASUREMENT UNCERTAINTY ............................................................................................. 5 3 GENERAL INFORMATION ........................................................................................................ 6 3.1 GENERAL DESCRIPTION OF EUT .......................................................................................... 6 3.2 DESCRIPTION OF TEST MODES ............................................................................................ 6 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................................ 7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................... 8 3.4 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 9 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ....................................................................... 9 4 TEST PROCEDURE AND RESULT ......................................................................................... 10 4.1 RADIATED EMISSION MEASUREMENT ............................................................................... 10 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT ............................................................. 10 4.1.2 TEST INSTRUMENT ............................................................................................................... 11 4.1.3 TEST PROCEDURE ................................................................................................................ 12 4.1.4 TEST SETUP ........................................................................................................................... 13 4.1.5 EUT OPERATING CONDITION ............................................................................................... 13 4.1.6 TEST RESULTS ....................................................................................................................... 14 4.2 20dB OCCUPIED BANDWIDTH MEASUREMENT ................................................................. 17 4.2.1 LIMITS OF EMISSION BANDWIDTH MEASUREMENT ......................................................... 17 4.2.2 TEST INSTRUMENT ............................................................................................................... 17 4.2.3 TEST PROCEDURE ................................................................................................................ 17 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 18 4.2.5 TEST SETUP ........................................................................................................................... 18 4.2.6 TEST RESULTS ....................................................................................................................... 18 4.3 DEACTIVATION TIME .............................................................................................................. 19 4.3.1 LIMITS OF DEACTIVATION TIME MEASUREMENT .............................................................. 19 4.3.2 TEST INSTRUMENTS ............................................................................................................. 19 4.3.3 TEST PROCEDURES ......................................................................................................... ..... 19 4.3.4 DEVIATION FROM TEST STANDARD ............................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST