2AA8R-SEA012SEA Wireless Charger

Sea Electronics Ltd. SEA012 user’s manual 1 SEA Wireless Charger User’s Manual Quick Instructions: 1. Plug the adaptor into the wall (110V/60Hz or 220V/50Hz). Connect the 19VDC adaptor output to the DC input jacket of the wireless charger plate. The blue LED of the charger plate will be turned on for a second and then turned off. The charger plate is now ready for charging (“waiting mode”). 2. Put the Qi‐compatible cell phone or other Qi‐compatible mobile devices on top of the central induction area where the QI logo is marked. The blue LED will be turned on when the charger starts charging the cell phone or mobile devices. The LED will be kept on during the charging process. 3. When the battery of the mobile device is fully charged, the charger will stop charging and turn the blue LED off. During the charging process, whenever the mobile device is removed from the charging plate, the charging process will be terminated automatically; the charger will be back in waiting mode and the blue LED will be off. Note:  The charger only supports QI compatible cell phone or mobile devices.  When place the mobile device on top of the charging plate, please align the receiving antenna of the cell phone with the transmitting antenna of the charging plate (“QI” mark in the plate). If the alignment is off more than 5mm‐10mm, the charging may not start or the cell phone may indicate “The charging device is not compatible”. In this case, please relocate the mobile device or cell phone on top of the charging plate.  When the mobile device is removed from the charging plate, the charging process will terminate immediately.  During the charging process, the induction area of the charging plate will be heated up. It is normal as long as the temperature is below 60°C. Specifications  Adaptor: AC input 110V~220V, 50Hz~60Hz; DC output 19V/0.5A  Wireless charger output: 5V/1A  Wireless charger operation frequency: 105KHz~205KHz  Maximum charging plate temperature: <60°C Regulatory and compliance  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  changes or modifications not expressly approved by the party responsible for Sea Electronics Ltd. SEA012 user’s manual 2 compliance could void the user’s authority to operate the equipment.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  ‐‐ Reorient or relocate the receiving antenna.  ‐‐ Increase the separation between the equipment and receiver.  ‐‐ Connect the equipment into an outlet on a circuit different  from that to which the receiver is connected.  ‐‐ Consult the dealer or an experienced radio/TV technician for help.  This ISM device complies with Canadian ICES‐001.  Cet appareil ISM est conforme à la norme NMB‐001 du Canada.

SEA Electronics Ltd Authority to Act as Agent Date: 2013-10-30 To Whom It May Concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co .. Ltd. (SGS) Shenzhen Branch and Hellen Wang in SGS-CSTC Standards Technical Services Co .. Ltd. {SGS) Shenzhen Branch to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: 12 months I By: Title: Director On behalf of: SEA Electronics Ltd. Telephone: (852)2667 2390 Frankie Ngan (Print name) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

SEA Electronics Ltd. Cover Letter‐Wireless Charger Approval FCC ID: 2AA8R‐SEA012 Data: Nov. 12, 2013 Gentlemen: There’s an Wireless SEA Wireless Charger that would like to have your authorization as an Inductive wireless power transfer applications approval. The specific product as below, Wireless SEA Wireless Charger, with its designed features and specified description, meets special requirements for KDB 680106 D01 section 5.2 requirements. Company: SEA Electronics Ltd. Product Name : Wireless SEA Wireless Charger Model Number: SEA012 FCC ID : 2AA8R‐SEA012 KDB 680106 D01 Section 5.2 Requirements: Product Technical Specification： Result: a) Power transfer frequency is less that 1 MHz 0.105~0.205MHz Complied b) Output power from each primary coil is less than 5 Watts <=5Watts Complied c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils --- Complied d) Client device is inserted in or placed directly in contact with the transmitter --- Complied e) The maximum coupling surface area of the transmit (charging) device is between 60 cm2 and 400 cm2. Please reference external photo .pdf Complied f) Aggregate leakage fields at 10 cm surrounding the device from all simultaneous transmitting coils are demonstrated to be less than 30% of the MPE limit. Please reference RF exposure report.pdf Complied Sincerely, By: __________________________ _________Frankie Ngan_______________ (Signature1) (Print name) Title: ______ Director_________ On behalf of: _____SEA Electronics Ltd.______ (Company Name) Telephone: ______(852)2667 2390 ________

SEA Electronics Ltd. Request for Confidentiality Date: 2013-10-30 Subject: Confidentiality Request for: FCC 10: 2AA8R-SEAO 12 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. *Note: Type of Confidentiality Requested 0 Short Tenn 1Zl Pennanent D ShortTenn D ShortTenn 0 ShortTenn D ShortTenn D ShortTenn D ShortTenn D ShortTenn 0 Pennanent* 1 [81 Pennanent D Pennanent [8J Pennanent 0 Pennanent* Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Tune-Up Procedure Schematics Test Setup Photos User's Manual SEA Electronics Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject infonnation easily available to "competition" would negate the advantage they have achieved by, developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be pennanently withheld from public review due to materials that contain trade secrets and proprietary infonnation not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short tenn confidential be withheld from public view for a period of days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event infonnation regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Pennanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: Frankie Ngan (Print name)

1.1 EUT Constructional Details Test Model No.: SEA012 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only Adapter: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document i…

Text truncated - open the document above for the full version.

1.1 EUT Constructional Details Test Model No.: SEA012 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only Adapter: This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle Section, Science & Technology Park, District Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130900527202 Page: 1 of 9 Authorized Signature: Starry Li EMC Laboratory Project Engineer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Human Exposure Report Application No.: SZEM1309005272RF Applicant/Manufacturer/ Factory: SEA Electronics Ltd. Address of Applicant/ Manufacturer/Factory: Unit G-F, 10/F, Blk A, Lianjian Bldg, Chanping Railway Station, Dongguan Guangdong. Equipment Under Test (EUT): EUT Name: SEA Wireless Charger Item No.: SEA012 Standards: 47 CFR PART 1, Subpart I, Section 1.1310 Date of Receipt: 2013-09-22 Date of Test: 2013-10-18 to 2013-10-31 Date of Issue: 2013-11-11 Test Result : PASS* * This report is just a test result base on the test method and limit requirement shown in the form on the second page. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government.. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM130900527202 Page: 2 of 9 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 2 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 CONTENTS ......................................................................................................................................... 2 3 GENERAL INFORMATION .................................................................................................................. 3 3.1 DETAILS OF E.U.T. ............................................................................................................................. 3 3.2 DESCRIPTION OF SUPPORT UNITS ........................................................................................................ 3 3.3 TEST LOCATION ................................................................................................................................. 3 3.4 TEST FACILITY.................................................................................................................................... 4 3.5 DEVIATION FROM STANDARDS .............................................................................................................. 4 3.6 ABNORMALITIES FROM STANDARD CONDITIONS...................................................................................... 4 4 EQUIPMENTS USED DURING TEST .................................................................................................. 4 5 TEST RESULTS .................................................................................................................................. 5 5.1 RF EXPOSURE TEST ........................................................................................................................... 5 5.1.1 E.U.T. Operation ...................................................................................................................... 5 Operating Environment: ........................................................................................................................ 5 EUT Operation: .................................................................................................................................... 5 5.1.2 Measurement Data .................................................................................................................. 6 6 PHOTOGRAPHS .........…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle Section, Science & Technology Park, Nanshan District Shenzhen, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130900527201 Page: 1 of 16 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC Test Report Application No.: SZEM1309005272RF Applicant/Manufacturer/ Factory: SEA Electronics Ltd. Address of Applicant/ Manufacturer/Factory: Unit G-F, 10/F, Blk A, Lianjian Bldg, Chanping Railway Station, Dongguan Guangdong. Equipment Under Test (EUT): EUT Name: SEA Wireless Charger Item No.: SEA012 FCC ID: 2AA8R-SEA012 Standards: 47 CFR PART 18: 2012 Date of Receipt: 2013-09-22 Date of Test: 2013-10-18 to 2013-10-31 Date of Issue: 2013-11-04 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM130900527201 Page: 2 of 16 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) te…

Text truncated - open the document above for the full version.