2AAL7-FM0222Bluetooth Speaker

CHARGING VIA USB CABLE TROUBLE SHOOTING INSTRUCTIONS BLUETOOTH SPEAKER MANUAL 1. Long press for power on and off, Short press it for pause/play. 2. Short press to volume up, Long press it to next song. 3. Short press to volume down, Long press it to previous song. 4. Support twin speakers playing: Long press both speakers to power on ○If twin speakers connected before, they will automatically connect each other ○ If twin speakers NOT connected before, short press twice on any speaker, two speakers will turn into pairing mode, after pairing successfully,the main speaker will have pairing voice prompt; ○ Short press twice on any of connected twin speakers to play as single speaker. ○ Switch off your bluetooth device(eg. mobile) bluetooth setup before twin speakers connection, once twin speakers connected successfully, switch on your device's bluetooth setup and search for the twin speaker name for bluetooth connection. 5. Insert TF card and the speaker will enter into TF card playing mode automatically. 6. Use audio cable to connect the speaker with your music device(MP3/Cell/PC), the ● Support Bluetooth/TF card/AUX/Twin Wireless Speakers Play/Hand Free Call ● Water-proof IPX5 ● Cannot turn on the speaker: check if the speaker does not have power, if no power, charge it first. ● Cannot connect with Bluetooth devices: check if speaker connected with the third Bluetooth device, if yes, disconnect it first, if still can not connect, reboot it and try again. ● Via USB cable, connect the speaker with the USB charger(output voltage 5V/output current no less than 1A, this accessory is not included) for charging; ● USB cable is for charging use only, not for data transferring; ● Built-in rechargeable Li-ion Battery ● Type-C charging Voltage: 5V ● Speaker: 4Ω 5W ● Frequency Range: 150Hz-15KHz ● Distortion ≤ 1% ● TF card slotPlug TF card into the card slot and the speaker will enter into TF card mode automatically. ● Type-C Port: Power Charging ● LED indicator ○ Blue flash: Power on. ○ Red: charging status (red indicator o ff when fully charged). ● Never knock the speaker ● Keep it away from fire, high and low temperature ● Never block speakers nets ● Never open it by yourself ● Don't charge it for too long time in case of damage to the batter y, 3 hours is the best charging time SPECIFICATIONS INTERFACES CAUTIONS Volume + Next Song TF Card slot Charging port Volume - Previous Song Power on/off 9. Low Battery: When the speaker is under low battery, it will have “beep” warning sound regularly, charge the speaker first then enjoy the speaker again. AUX port FM0222 231111 7. RESET: When the speaker is on and stuck, push for 10 seconds to reboot the BASIC FEATURES speaker will change to AUX mode automatically and play music directly. - speaker Mode Change 8. Long press the “M” button to switch Bluetooth/TF card/AUX modes, Short press the “M” button to change different LED modes. FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

FORM ELECTRONICS CO.,Ltd 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-3-25 To whom it may concern: We, FORM ELECTRONICS CO.,Ltd, hereby certify that the equipment for which authorization is sought (FCC ID: 2AAL7-FM0222) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Martin Wang N/A FORM ELECTRONICS CO.,Ltd 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

FORM ELECTRONICS CO.,Ltd 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-3-25 U.S. Agent Designation FORM ELECTRONICS CO.,Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2AAL7- FM0222): Name and company of U.S. agent: ACT Lab LLC Physical U.S. address of agent: 3280 East 59th Street Long Beach, CA 90805 United States FRN of U.S. agent: 0033465568 Email address of U.S. agent: [email protected] ACT Lab LLC acknowledges their obligation to accept service of process on behalf of FORM ELECTRONICS CO.,Ltd. FORM ELECTRONICS CO.,Ltd with the FRN [0022829261] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Martin Wang N/A FORM ELECTRONICS CO.,Ltd Signature Scott Huber Senior Technical Director ACT Lab LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-3-25> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AAL7-FM0222 FM0222 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Martin Wang Company: FORM ELECTRONICS CO.,Ltd Address: 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Phone: 86-755-84196007 Fax: 86-755-84193911 E-Mail: [email protected]

FORM ELECTRONICS CO.,Ltd 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-3-25 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AAL7-FM0222 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Martin Wang Company: FORM ELECTRONICS CO.,Ltd Address: 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Phone: 86-755-84196007 Fax: 86-755-84193911 E-Mail: [email protected]

FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo 5 Appearance of EUT

FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Appendix IID Label Appendix II ID Label Location Bluetooth Speaker FCC ID: 2AAL7-FM0222 Model: FM0222

FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 6 Internal of EUT Photo 7 Internal of EUT FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo 8 Appearance of PCB & Battery Photo 9 Internal of Battery FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo 10 Appearance of PCB Photo 11 Appearance of PCB FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo 12 Appearance of PCB Antenna

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202403-0170-1 Page: 1 of 3 TB-RF-074-1.0 1 A/F., Building.6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao’an, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2AAL7-FM0222 1. Client Information Applicant : FORM ELECTRONICS CO.,Ltd Address : 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China Manufacturer : FORM ELECTRONICS CO.,Ltd Address : 4F Bldg E, Junfeng Science&Technology Park, Lezhujiao, Xixiang, Bao'an Dist, Shenzhen, China 2. General Description of EUT EUT Name : Bluetooth Speaker Model(s) No. : FM0222 Model Difference : ---- Product Description : Operation Frequency: Bluetooth 5.2(BR+EDR): 2402MHz~2480MHz Number of Channel: 79 channels Antenna Gain: 1.7dBi PCB Antenna Modulation Type: GFSK(1Mbps) π/4-DQPSK(2Mbps) 8-DPSK(3Mbps) Power Supply : Input: DC 5V/650mA DC 3.7V 1200mAh 4.44Wh Rechargeable Li-ion battery Software Version : MZH_147016F3(FM0222)_20231204 Hardware Version : FM0222-V04 2024-01-16 Remark: The antenna gain provided by the applicant, the adapter and verified for the RF conduction test and adapter provided by TOBY test lab. Note: More test information about the EUT please refer the RF Test Report. Report No.: TBR-C-202403-0170-1 Page: 2 of 3 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤7.5.0 for 10-g SAR Report No.: TBR-C-202403-0170-1 Page: 3 of 3 TB-RF-074-1.0 2. Calculation: Test separation: 5mm Bluetooth Mode (GFSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 1.378 1±1 2 1.585 0.491 3.0 2.441 0.755 0±1 1 1.259 0.393 3.0 2.480 0.322 0±1 1 1.259 0.397 3.0 Bluetooth Mode (Pi/4-DQPSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 3.480 3±1 4 2.512 0.779 3.0 2.441 2.824 2±1 3 1.995 0.623 3.0 2.480 2.319 2±1 3 1.995 0.628 3.0 Bluetooth Mode (8-DPSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dBm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 4.270 4±1 5 3.162 0.980 3.0 2.441 3.602 3±1 4 2.512 0.785 3.0 2.480 3.137 3±1 4 2.512 0.791 3.0 The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF THE REPORT-----

BUILDWIN 1 BUILDWIN 2 Horizontal:2400MHz2450MHz2500MHz Power(dBm) Max:0Min:-40Scale:5/div Frequency (MHz) Gain(dBi) MaxMinAvg 2400-1.73178-30.0815-8.48713 2450-0.845801-38.5605-7.88012 2500-0.685586-24.0318-6.79139 Vertical:2400MHz2450MHz2500MHzPower(dBm) Max:0Min:-30Scale:5/div Frequency (MHz) Gain(dBi) MaxMinAvg 2400-6.1530-24.1420-13.0295 2450-3.7054-26.5836-10.6700 2500-2.32122-30.4301-9.70536 ANTTestLabs：AttestationofGlobalComplianceCo.,Ltd BUILDWIN3

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 1 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 RF Test Data for Bluetooth(BR+EDR) (Conducted Measurements) General Description of EUT Product Name: Bluetooth Speaker Test Model: FM0222 Sample ID: HC-C-202403-0170-01-01-2# Environmental Conditions Temperature: 23.8°C Relative Humidity: 48% Test Voltage: DC 3.7V Test Engineer: Mike Yan Note: For a more detailed features description, please refer to the report TBR-C-202403-0170-6 The report only show the worst case data. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 2 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT 1-DH1 2402 Ant1 32 4.95 2.5 NVNT 1-DH1 2441 Ant1 32 4.95 2.5 NVNT 1-DH1 2480 Ant1 32 4.95 2.5 NVNT 2-DH1 2402 Ant1 32.8 4.84 2.44 NVNT 2-DH1 2441 Ant1 32.8 4.84 2.44 NVNT 2-DH1 2480 Ant1 32.8 4.84 2.44 NVNT 3-DH1 2402 Ant1 32.8 4.84 2.44 NVNT 3-DH1 2441 Ant1 32.8 4.84 2.44 NVNT 3-DH1 2480 Ant1 32.8 4.84 2.44 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 3 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Test Graphs Duty Cycle NVNT 1-DH1 2402MHz Ant1 Duty Cycle NVNT 1-DH1 2441MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 4 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Duty Cycle NVNT 1-DH1 2480MHz Ant1 Duty Cycle NVNT 2-DH1 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 5 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Duty Cycle NVNT 2-DH1 2441MHz Ant1 Duty Cycle NVNT 2-DH1 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 6 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Duty Cycle NVNT 3-DH1 2402MHz Ant1 Duty Cycle NVNT 3-DH1 2441MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 7 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Duty Cycle NVNT 3-DH1 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 8 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Limit (dBm) Verdict NVNT 1-DH1 2402 Ant1 1.378 21 Pass NVNT 1-DH1 2441 Ant1 0.755 21 Pass NVNT 1-DH1 2480 Ant1 0.322 21 Pass NVNT 2-DH1 2402 Ant1 3.480 21 Pass NVNT 2-DH1 2441 Ant1 2.824 21 Pass NVNT 2-DH1 2480 Ant1 2.319 21 Pass NVNT 3-DH1 2402 Ant1 4.270 21 Pass NVNT 3-DH1 2441 Ant1 3.602 21 Pass NVNT 3-DH1 2480 Ant1 3.137 21 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 9 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Test Graphs Power NVNT 1-DH1 2402MHz Ant1 Power NVNT 1-DH1 2441MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 10 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Power NVNT 1-DH1 2480MHz Ant1 Power NVNT 2-DH1 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 11 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Power NVNT 2-DH1 2441MHz Ant1 Power NVNT 2-DH1 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 12 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Power NVNT 3-DH1 2402MHz Ant1 Power NVNT 3-DH1 2441MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 13 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Power NVNT 3-DH1 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202403-0170-6 Page: 14 of 68 FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 3. -20dB Bandwidth Condition Mode Frequency (MHz) Antenna -20 dB Bandwidth (MHz) Limit -20 dB Bandwidth (MHz) Verdict NVNT 1-DH1 2402 Ant1 0.85 ---- Pass NVNT 1-DH1 2441 Ant1 0.86 ---- Pass NVNT 1-DH1 2480 Ant1 0.88 ---- Pass NVNT 2-DH1 2402 Ant1 1.23 ---- Pass NVNT 2-DH1 2441 Ant1 1.27 ---- Pass NVNT 2-DH1 2480 Ant1 1.24 ---- Pass NVNT 3-DH1 2402 Ant1 1.24 ---- Pass NVNT 3-DH1 2441 Ant1 1.24 ---- Pass NVNT 3-DH1 2480 Ant1 1.25 ---- Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, S…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202403-0170-6 Page: 1 of 48 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 RF Test Report FCC ID: 2AAL7-FM0222 Report No. : TBR-C-202403-0170-6 Applicant : FORM ELECTRONICS CO.,Ltd Equipment Under Test (EUT) EUT Name : Bluetooth Speaker Model No. : FM0222 Series Model No. : ---- Brand Name : ---- Sample ID : HC-C-202403-0170-01-01-1#&HC-C-202403-0170-01-01-2# Receipt Date : 2024-03-19 Test Date : 2024-03-19 to 2024-03-25 Issue Date : 2024-03-25 Standards : FCC Part 15 Subpart C 15.247 Test Method : ANSI C63.10:2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Tested By : Mike Yan Reviewed By : Wade. Lv Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202403-0170-6 Page: 2 of 48 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT.............................................................................. 6 1.1 Client Information ................................................................................................................. 6 1.2 General Description of EUT (Equipment Under Test) ................................................... 6 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 8 1.4 Description of Support Units .............................................................................................. 8 1.5 Description of Test Mode .................................................................................................... 9 1.6 Description of Test Software Setting .............................................................................. 10 1.7 Measurement Uncertainty ................................................................................................ 10 1.8 Test Facility ......................................................................................................................... 11 2. TEST SUMMARY ..................................................................................................................... 12 3. TEST SOFTWARE ................................................................................................................... 12 4. TEST EQUIPMENT AND TEST SITE ................................................................................... 13 5. CONDUCTED EMISSION ....................................................................................................... 15 5.1 Test Standard and Limit .................................................................................................... 15 5.2 Test Setup ........................................................................................................................... 15 5.3 Test Procedure ................................................................................................................... 15 5.4 Deviation From Test Standard ......................................................................................... 16 5.5 EUT Operating Mode ........................................................................................................ 16 5.6 Test Data ............................................................................................................................. 16 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 17 6.1 Test Standard and Limit .................................................................................................... 17 6.2 Test Setup ........................................................................................................................... 19 6.3 Test Procedure ................................................................................................................... 20 6.4 Deviation From Test Standard ......................................................................................... 21 6.5 EUT Operating Mode ........................................................................................................ 21 6.6 Test Data ............................................................................................................................. 21 7. EMISSIONS IN RESTRICTED BANDS ............................................................................... 22 7.1 Test Standard and Limit .................................................................................................... 22 7.2 Test Setup ........................................................................................................................... 22 7.3 Test Procedure ................................................................................................................... 23 7.4 Deviation From Test Standard ......................................................................................... 24 Report No.: TBR-C-202403-0170-6 Page: 3 of 48 TB-RF-074-1.0 7.5 EUT Operating Mode ........................................................................................................ 24 7.6 Test Data ............................................................................................................................. 24 8. 99% OCCUPIED AND 20DB BANDWIDTH ........................................................................ 25 8.1 Test Standard and Limit .........................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Appendix V EUT Test Photographs Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) FCC ID: 2AAL7-FM0222 TB-RF-074-1.0 Photo of Setup for Radiated Emission (Above 1 GHz) Photo of Setup for Conducted Emission -----END OF THE REPORT-----