2AANUAEH2130Smart Home Temperature/Humidity Sensor

Safety and Warranty Before using your set: Check out details inside this booklet 2015 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. AEH2900_2950_37_Safety and Warranty_V1.0 wk1510.1 English Important safety instructions Safety CAUTION : For INDOOR USE ONLY! DO NOT use this Intelligent switch with non-resistive loads, such as motors, compact fluorescent light (CFL) bulbs or fluorescent lighting.To reduce the risk of electric shock, this Intelligent switch has a third (grounding) pin. As a grounding type plug, this Intelligent switch only fits into a grounding type power outlet. Make sure that you use this Intel- ligent switch with a grounding type power outlet that has been properly installed by a qualified electrician. Important Safety Instructions a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Clean only with dry cloth. f The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. • Perchlorate Material - special handling may apply. See www.dtsc. ca.gov/hazardouswaste/perchlorate. g This product shall not be exposed to dripping or splashing. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice for the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the receiving antenna. • Increase the separation between equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • this device may not cause harmful interference, and • this device must accept any interference received, including interfer- ence that may cause undesired operation. Notice for Canada • This device complies with Industry Canada licence-exempt RSS standard(s): Operation is subject to the following Two conditions: (1) this device may not cause interference, and (2) this device must ac- cept any interference, including interference that may cause undesired operation of the device.. Care of the environment Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polysty- rene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if dis- assembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, and old equipment. Disposal of your old product and battery Your product is designed and manufactured with high quality mate- rials and components, which can be recycled and reused. This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com. This product contains batteries: • Dispose of batteries properly. Do not incinerate. Batteries may explode if overheated. • Do not wrap in metal or aluminum foil. Wrap in newspaper before discarding. • It is suggested that you contact your local town or city to determine proper battery redemption site(s) in your area. • Please visit www.call2recycle.org for additional information on a recycling center in your area for rechargeable batteries. Notice Disclaimer • Your use of Philips SmartHome is at your sole risk. Gibson Innovations and its subsidiary companies (individually and collectively “Gibson Innovations”) are not responsible for the operation of such Philips SmartHome or your use thereof and Gibson Innovations shall have no liability to you related thereto. • The sensors and/or Intelligent switch are intended as an aid. They are not substitutes for home security supervision and should not be used as such. Written Offer Gibson Innovations hereby offers to deliver, upon request, a copy of the complete corresponding source code for the copyrighted open source software packages used in this product for which such offer is requested by the respective licenses. This offer is valid up to three years after product purchase. To obtain source code, please contact [email protected]. If you prefer not to use email or if you do not receive confirmation receipt within a week after mailing to this email address, please write to Open Source Team, 6/F, Philips Electronics Building, 5 Science Park East Avenue, Hong Kong Sci- ence Park, Shatin, New Territories, Hong Kong. If you do not receive timely confirmation of your letter, please email to the email address above. Specifications are subject to change without notice. Philips and the Philips’ Shield Emblem are registered trademarks of Konink…

Text truncated - open the document above for the full version.

Model Confirmation Letter We WOOX Innovations Limited certify the product: Smart Home Temperature and Humidity Sensor And the item No.: AEH2130/ZZ, where zz=00-99, are ident ical in interior structure, electrical circuits and components, only difference of plug portion and exported countries. and model number. Agency Agreement Expiration Date: __ May 09, 2015_____ Date: 2015-03-10 By: Benson Lai (Signature 1 ) (Print name) Title: _____ Manager ____ On behalf of: ______WOOX Innovations Limited ________ (Company Name) Telephone: ___ 852 3468 3267 _____

1 Photographs - EUT Constructional Details Test Model No.: AEH2130/37

1 Photographs - EUT Constructional Details Test Model No.: AEH2130/37

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200069202 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1502000692CR(GZEM1501000535CR) Applicant: WOOX Innovations Ltd. Manufacturer: WOOX Innovations Ltd. Factory: Arts Electronics Co., Ltd. Product Name: Smart Home Temperature/Humidity Sensor Model No.(EUT): AEH2130/37 Add Model No.: AEH2130/zz, where zz = 00 - 99 (different exported countries.) Trade Mark: PHILIPS FCC ID: 2AANUAEH2130 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-02-09 Date of Test: 2015-02-11 to 2015-03-05 Date of Issue: 2015-03-10 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200069202 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-03-10 Original Authorized for issue by: Tested By 2015-03-05 (Chris Zhong) /Project Engineer Date Prepared By 2015-03-10 (Vivi Zhou) /Clerk Date Checked By 2015-03-12 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150200069202 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are ret…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150200069201 Page: 1 of 49 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1502000692CR(GZEM1501000535CR) Applicant: WOOX Innovations Ltd. Manufacturer: WOOX Innovations Ltd. Factory: Arts Electronics Co., Ltd. Product Name: Smart Home Temperature/Humidity Sensor Model No.(EUT): AEH2130/37 Add Model No.: AEH2130/zz, where zz = 00 - 99 (different exported countries.) Trade Mark: PHILIPS FCC ID: 2AANUAEH2130 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-02-09 Date of Test: 2015-02-11 to 2015-03-05 Date of Issue: 2015-03-10 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200069201 Page: 2 of 49 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-03-10 Original Authorized for issue by: Tested By 2015-03-05 (Chris Zhong) /Project Engineer Date Prepared By 2015-03-10 (Vivi Zhou) /Clerk Date Checked By 2015-03-12 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150200069201 Page: 3 of 49 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenn…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: AEH2130/37 1.1 Radiated Emission 1.2 Radiated Spurious Emission