2AANUAJT4400Clock Radio

www.philips.com/support User manual Always there to help you Register your product and get support at Question? Contact Philips 1EN Contents 1 Important 2 Safety 2 2 Your clock radio 4 Introduction 4 What's in the box 4 Overview of the clock radio 4 3 Get started 6 Install battery 6 Connect power 6 Set clock 6 4 Listen to FM radio 7 Tune to FM radio stations 7 Store FM radio stations automatically 7 Store FM radio stations manually 7 Select a preset radio station 7 Adjust volume 7 5 Use Bluetooth devices 8 Connect a device 8 Play audio from Bluetooth-enabled device 8 Bluetooth icon status 9 Clear the pairing information 9 Control your phone call 9 6 Set alarm timer 10 Set alarm 10 Activate/deactivate alarm timer 10 Snooze the alarm 10 7 Other features 11 Set sleep timer 11 Charge your device 11 Adjust display brightness 11 8 Product information 12 Specifications 12 9 Troubleshooting 13 10 Notice 14 Compliance 14 Care of the environment 14 2EN 1 Important Safety Know these safety symbols This 'bolt of lightning' indicates uninsulated material within your unit may cause an electric shock. For the safety of everyone in your household, please do not remove product covering. The 'exclamation mark' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus. CAUTION: To prevent electric shock, fully insert the plug. (For regions with polarized plugs: To prevent electric shock, match wide blade to wide slot.) Important safety instructions a Read these instructions. b Keep these instructions. c Heed all warnings. d Follow all instructions. e Do not use this apparatus near water. f Clean only with dry cloth. g Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. h Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. i Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. j Only use attachments/accessories specified by the manufacturer. k Unplug this apparatus during lightning storms or when unused for long periods of time. l Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. m Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit: • Install all batteries correctly, + and - as marked on the unit. • Remove batteries when the unit is not used for a long time. n Apparatus shall not be exposed to dripping or splashing. o Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted candles). p This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling 3EN information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. q Where the plug of the Direct Plug-in Adapter is used as the disconnect device, the disconnect device shall remain readily operable. Note • The type plate is located on the bottom of the apparatus. 4EN 2 Your clock radio Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction With this clock radio, you can: • listen to FM radio; • play audio from Bluetooth-enabled devices; • make phone calls; • set two alarms, and • wake up to buzzer or radio. What's in the box Check and identify the contents of your package: • Clock radio • Short User Manual Overview of the clock radio a b c d e f g h i j k l m n o q p a • Set Alarm 1. • View alarm settings. • Activate or deactivate alarm timer. b • Set sleep timer. c RADIO • Turn the radio on or off. d SNOOZE/BRIGHTNESS • Snooze the alarm. • Adjust display brightness. e • Select Bluetooth source. f • Play or pause the Bluetooth music playback. • Answer an incoming call. • Reject an incoming call. g • Set Alarm 2. • View alarm settings. • Activate or deactivate alarm timer. h SCAN/PROG • Scan and store FM radio stations automatically. • Program the sequence of the radio stations. 5EN i + PRESET/ MIN - • Adjust minute. • Select preset radio stations. j SET TIME/12/24 HR • Press to enter timer setting mode. • Press and hold to set 12 or 24 time format. k + TUNING/ HR - • Adjust hour. • Tune to FM radio stations. l Display panel m VOL knob • Adjust volume. n FM ANT • Improve FM reception. o Power plug • Connect AC power. p USB socket • Charge your mobile devices. q Battery compartment 6EN 3 Get started Always follow the instructions in this chapter in sequence. Install battery Caution • Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire. •Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. •The batteries contain chemical substances, so they should be disposed of properly. You can only use AC power as power supply. The battery can only back up clock and alarm settings. • Install two AA batteries (not supplied) as illustrated below: Connect power Caution • Risk of product damage! Make sure that the power voltage corresponds to the voltage printed on the back or underside of the clock radio. •Risk of electric shock! When you unplug the AC plug, always pull the plug from the socket. Never pull the cord. Set clock 1 Press SET TIME/ 12/24 HR …

Text truncated - open the document above for the full version.

Request for Confidentiality Date: _2015- 5- 26___ Subject: Confidentiality Request for: FCC ID: 2AANUAJT4400 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ _Gibson Innovations Limited has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: _______________________________ Benson Lai Manager, Safety and Compliance (Print name)

Authority to Act as Agent Date: _2015.5.26_______ To Whom It May Concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Vicky Yuan in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ___July, 25 2015_____ By: Benson Lai (Signature) (Print name) Title: Manager, Safety and Compliance On behalf of: Gibson Innovations Limited (Company Name) Telephone: 852-3468 3267

1 Photographs - EUT Constructional Details Test model No.: AJT4400B/37

FCC ID: 2AANUAJT4400 IC11260A-AJT4400 FCC ID: 2AANUAJT4400 IC11260A-AJT4400 Label location_________ ___FCC ID location ___IC ID location

JOB.: AJT4400B/37 D-BOX LABEL SIZE: W52xH45 mm JOB.: AJT4400B/37 CARTON LABEL SIZE: W104xH100 mm Model No.: AJT4400B/37 CLOCK RADIO 4X AJT4400B/37 CLOCK RADIO 1X 0.6 1.3 JOB.: AJT4400B/37 RATING LABEL SIZE: W49.5xH24.5 mm AC100-240V~50/60Hz 10W Model No.: AJT4400B/37 Made in China Model No.: AJT4400B/37 DC 3V 2x1.5V AA Size Manufactured: May / 2015 CAN ICES-3(B)/NMB-3(B) Gibson Innovations USA Inc.3070 Windward Plaza Suite F, Box 735Alpharetta, GA 30005 Serial No.: AQPA1516000001 Model No.: AJT4400B/37 Serial No.: AQPA1516000001 8670 001 28025 MADE IN CHINA Fabriqué en Chine Hecho en China 8670 001 28025 MADE IN CHINA Fabriqué en Chine Hecho en China Imported by/Importé par: Gibson Innovations USA Inc.3070 Windward Plaza Suite F, Box 735Alpharetta, GA 30005 Imported by/Importé par:Gibson Innovations USA Inc. 3070 Windward Plaza Suite F, Box 735Alpharetta, GA 30005 86 8 9 4 4 6 0 0 1 6 8 86 8 9 4 4 6 0 0 1 6 8 10889446001683

1 Photographs - EUT Constructional Details Test model No.: AJT4400B/37

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150500253703 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1505002537CR Applicant: Gibson Innovation Limited Manufacturer: Gibson Innovation Limited Factory: Yusan Technology(Shenzhen) Limited Product Name: Clock Radio Model No.(EUT): AJT4400B/37 Add Model No.: AJT4400W/37, AJT4400x/yy (x can be letter A to Z or nil, yy can be letter 00 to 99) FCC ID: 2AANUAJT4400 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-05-15 Date of Test: 2015-05-15 to 2015-05-20 Date of Issue: 2015-05-27 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150500253703 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-05-27 Original Authorized for issue by: Tested By 2015-05-20 (Eric Fu) /Project Engineer Date Prepared By 2015-05-27 (Sade Luo) /Clerk Date Checked By 2015-06-01 (Owen Zhou) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM150500253703 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150500253702 Page: 1 of 111 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1505002537CR Applicant: Gibson Innovation Limited Manufacturer: Gibson Innovation Limited Factory: Yusan Technology(Shenzhen) Limited Product Name: Clock Radio Model No.(EUT): AJT4400B/37 Add Model No.: AJT4400W/37, AJT4400x/yy (x can be letter A to Z or nil, yy can be letter 00 to 99) FCC ID: 2AANUAJT4400 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-05-15 Date of Test: 2015-05-15 to 2015-05-20 Date of Issue: 2015-05-27 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150500253702 Page: 2 of 111 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-05-27 Original Authorized for issue by: Tested By 2015-05-20 (Eric Fu) /Project Engineer Date Prepared By 2015-05-27 (Sade Luo) /Clerk Date Checked By 2015-06-01 (Owen Zhou) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150500253702 Page: 3 of 111 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Par…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: AJT4400B/37 1.1 Conducted Emission 1.2 Radiated Emission 1.3 Radiated Spurious Emission