2AANUTX2BTBluetooth Headphones

www.philips.com/support User manual Always there to help you Register your product and get support at Question? Contact Philips TX2BT 1EN Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your Bluetooth in-ear headphones 3 What's in the box 3 Other devices 3 Overview of your Bluetooth in-ear headphones 3 3 Get started 4 Charge your headphones 4 Pair the headphones with your mobile phone 4 4 Use your headphones 6 Connect the headphones to a Bluetooth device 6 Manage your calls and music 6 Share your music 7 5 Technical data 8 6 Notice 9 Notice of compliance 9 Disposal of your old product and battery 9 Trademarks 10 7 Frequently asked questions 11 2EN 1 Important safety instructions Hearing Safety Danger •To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can’t hear what’s around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. • Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. General information To avoid damage or malfunction: Caution •Do not expose headphones to excessive heat. •Do not drop your headphones. •Headphones shall not be exposed to dripping or splashing. •Do not allow your headphones to be submerged in water. •Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. •If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. •The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. •Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. About operating and storage temperatures and humidity • Operate or store in a place where temperature is between -15ºC (5ºF) and 55ºC (131ºF) (up to 90% relative humidity. • Battery life may be shorter in high or low temperature conditions. 3EN 2 Your Bluetooth in-ear headphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless in-ear headphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. What's in the box Philips Bluetooth in-ear headphones TX2BT Replaceable rubber ear caps USB charging cable (for charging only) Quick start guide Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headphones (see 'Technical data' on page 8). Overview of your Bluetooth in-ear headphones a Microphone b On/off, music/call control control button c NFC detection area d LED indicator e Micro USB charging slot f Volume/Track control button b a c e f d 4EN 3 Get started Charge your headphones Note •Before you use your headphones for the first time, charge the battery for 5 hours for optimum battery capacity and lifetime. •Use only the original USB charging cable to avoid any damage. •Finish your call before charging the headphones, as connecting the headphones for charging will power the headphones off. •You can operate the headphones normally during charging. Connect the supplied USB charging cable to: • the micro USB charging slot on the headphones and; • the charger/USB port of a computer. »LED turns white during charging and turns off when the headphones is fully charged. Tip •Normally, a full charge takes 2 hours. Pair the headphones with your mobile phone Before you use the headphones with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one. There are two ways to pair your headphones with your mobile phone: • Manual pairing • NFC pairing Manual pairing 1 Make sure that the headphones are fully charged and turned off. 2 Press and hold the on/off button until the blue and white LED flashes alternately. »The headphones remain in pairing mode for 5 minutes. 3 Make sure that the mobile phone is turned on and its Bluetooth feature is activated. 4 Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone. NFC pairing 1 Make sure your headphones are turned on. 2 Make sure you turn on the NFC function on your phone and your phone’s screen remains active. 3 Place your phone over the headset so that the NFC detection area of each device can touch each other. 4 Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone. Note •Make sure your mobile phone has the NFC feature available and switched on. •Make sure your mobile phone is not in standby mode. •Pairing with NFC is only suitable for Android mobile operating system 4.2 or above. •Refer to the user manual of your mobile phone to identify its NFC detection area. The following example shows you how to pair the headphones with your mobile phone. 1 Activate the Bluetooth feature of your mobile phone, select Philips TX2BT. 5EN 2 Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Blueto…

Text truncated - open the document above for the full version.

Authority to Act as Agent Date: 2015-06-15 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: __SGS-CSTC Standards Technical Services Co., Ltd.__ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____August 14, 2015___ By: __________________________ ___ Benson Lai ______ (Signature 1 ) (Print name) Title: ________Manager________ On behalf of: __ Gibson Innovations Limited __ (Company Name) Telephone: ____852 3468 3267_____ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 022311 – 6

Request for Confidentiality Date: 2015-6-15 Subject: Confidentiality Request for FCC ID: 2AANUTX2BT IC:11260A-TX2BT Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ______ Gibson Innovations Limited _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 3 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NO TE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. S incerely, By: __________________________ ___Benson Lai/ Manager ____ (Signature/Title 4 ) (Print name) 2 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-B ut-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 4 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 022311 – 6

External Photo

11.0 11.0 11.0 11.0 LE1A1522000001 LE1A1522000001 LE1A1522000001 LE1A1522000001 112mm :(:фս߶঎ૉ஍ѹ৥֣ фս߶঎

Internal Photo

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Application No..: GZEM1504001801CR Page: 1 of 1 FCC ID: 2AANUTX2BT This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspxand,for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. RF Exposure Compliance Requirement The product belongs to standalone portable device base the FCC rule part 2.1091&2.1093. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Radiated Output Power and SAR Test Exclusion Threshold (mW) are listed below: FHSS Transmit frequency (GHz) Max Radiated Output Power (dBm) Max Radiated Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 -5.95 0.254 9.7 2.441 -8.74 0.134 9.6 2.480 -5.23 0.300 9.5 DSSS Transmit frequency (GHz) Max Radiated Output Power (dBm) Max Radiated Output Power (mW) SAR Test Exclusion Threshold (mW) 2.402 -6.31 0.233 9.7 2.442 -6.57 0.220 9.6 2.480 -5.51 0.281 9.5 The SAR Test Exclusion Threshold for 100 MHz to 6 GHz is calculated from: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v05r02, the SAR report is not required.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch 19 8 Ke zhu Roa d, Scient ech Park, Guangzhou Economic & Technolo gical De velopment D istrict, Guangzhou, China 510663 Telephon e: +86 (0) 20 8 2155555 Fax: +86 (0) 20 820750 59 Email: ee. guangzh [email protected] Report No.: GZEM150400188001 Page: 1 of 82 FCC ID: 2AANUTX2BT Authorized Signature: Jerry Chan Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspxand,for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. 1 Cover Page TEST REPORT The following sample(s) was/were submitted and identified on behalf of the client as: Application No.: GZEM1504001880CR Applicant: Gibson Innovations Limited Manufacturer: The same as applicant FCC ID: 2AANUTX2BT Product Description: Bluetooth Headphones Model No.: TX2BT, TX2BT/XX, TX2BTYY/XX (YY=AA to ZZ, XX=00 to 99) ♣ ♣ Please refer to section 3 of this report for further details. Trade Mark: Philips Standards: CFR 47 FCC PART 15 Subpart C: 2014 section 15.247 Date of Receipt: 2015-05-14 Date of Test: 2015-05-21 to 2015-05-27 Date of Issue: 2015-07-29 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM150400188001 Page: 2 of 82 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspxand,for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-07-29 Original Report Authorized for issue by: Tested By 2015-05-21 to 2015-05-27 (Curry Wu) /Project Engineer Date Prepared By 2015-06-05 (Icy Chen) / Clerk Date Checked By 2015-06-05 (Little Xiang) / Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch Report No.: GZEM150400188001 Page: 3 of 82 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspxand,for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such s…

Text truncated - open the document above for the full version.

Test Setup Photo 1.1 RADI ATE D EM ISS IO NS WHICH F ALL I N TH E RE STRICT ED B AN DS Below 1G: Above 1 GHz: