2AAPY-YC7RDKIDS TABLET

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE1:Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE2: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE3:The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. NOTE4:This device and its antenna(s)must not be co-located or operating in conjunction with any other antenna or transmitter.

SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2013-8-20 SUBJECT: FCC Application for (FCC ID: 2AAPY-YC7RD) To Whom It May Concern: We, the undersigned, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. We understand that devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm Select the "accredited" option to search for FCC recognized accredited test firms. Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. Regards, Signatory Signature Name: Jazzy Jia Title: Manager Tel: +86-755-61156511

SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED Model Difference FCC ID: 2AAPY-YC7RD Model : YC7RD, YC7RQ, YC7RS All the models are the same circuit and RF module, except the mode names. Regards, Client’s signature Signature Name: Jazzy Jia Title: Manager Tel: +86-755-61156511

SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 2013/8/20 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product： KID’S TABLET Trade Name： N/A Model Name： YC7RD Serial Model： YC7RQ, YC7RS FCC ID : 2AAPY-YC7RD We affirm that between SIEMIC and SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature Name: Jazzy Jia Title: Manager Address: 1106, West Building Digital Culture Industry Base, Nanshan District, Shenzhen, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED 2013-8-20 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AAPY-YC7RD We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Signature Name: Jazzy Jia Title: Manager Address: 1106, West Building Digital Culture Industry Base, Nanshan District, Shenzhen, China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8

FCC ID LABELING AND LOCATION FCC ID Label KID’S TABLET Model NO.：YC7RD Input Rating：DC 5V/ 2000mA （Charging by Notebook） Battery:3.7V/ 2400mAh FCC ID: 2AAPY-YC7RD Destiny Pro Tech, LLC Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Photo 9 Photo 10 Photo 11 Photo 12 ANT Photo 13 Photo 14 Photo 15

FCC ID : 2AAPY-YC7RD RF EXPOSURE EVALUATION METHOD SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. FCC ID : 2AAPY-YC7RD Maximum measured transmitter power. frequency Maximum Peak Conducted Output Power Maximum AV Conducted Output Power Max Antenna Gain GHz dBm dBm dBi 2.437 12.75 9.79 1.0 Remark: The best case gain of the antenna is 1.0dBi. 1.0dBi logarithmic terms convert to numeric result is nearly 1.22 9.79dbm=9.53mW [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance,mm)] · [√f(GHz)]= 9.53/5*√2.437=2.97≤3.0 Threshold at which no SAR required is 10mw and ≤ 3.0 for 1-g SAR, Separation distance is 5mm. Conclusion: No SAR is required.

FCC RADIO TEST REPORT FCC ID: 2AAPY-YC7RD Product： KID’S TABLET Trade Name： N/A Model Name： YC7RD Serial Model： YC7RQ, YC7RS Report No.： NTEK- 2013NT0724802F Prepared for SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED 1106, West Building Digital Culture Industry Base, Nanshan District, Shenzhen, China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 66 Report No.: NTEK-2013NT0724802F TEST RESULT CERTIFICATION Applicant’s name................. : SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED Address ................................. : 1106, West Building Digital Culture Industry Base, Nanshan District, Shenzhen, China Manufacture's Name............ : SHENZHEN YOUNG CLOUD TECHNOLOGY CO., LIMITED Address ................................. : 1106, West Building Digital Culture Industry Base, Nanshan District, Shenzhen, China Product description Product name ........................... : KID’S TABLET Model and/or type reference : YC7RD Serial Model .............................. : YC7RQ, YC7RS Standards............................. : FCC Part15.247 Test procedure .............................. ANSI C63.4-2003 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test............................................: Date (s) of performance of tests .............: 24 Jul. 2013 ~ 19 Aug. 2013 Date of Issue...........................................: 19 Aug. 2013 Test Result...............................................: Pass Testing Engineer : (Apple Huang) Technical Manager : (Brown Lu) Authorized Signatory : (Bovey Yang) Page 3 of 66 Report No.: NTEK-2013NT0724802F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 9 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 11 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3 . EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 3.1.2 TEST PROCEDURE 14 3.1.3 DEVIATION FROM TEST STANDARD 14 3.1.4 TEST SETUP 14 3.1.5 EUT OPERATING CONDITIONS 14 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 17 3.2.1 RADIATED EMISSION LIMITS 17 3.2.2 TEST PROCEDURE 18 3.2.3 DEVIATION FROM TEST STANDARD 18 3.2.4 TEST SETUP 19 3.2.5 EUT OPERATING CONDITIONS 20 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 21 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 22 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) 24 4 . POWER SPECTRAL DENSITY TEST 37 4.1 APPLIED PROCEDURES / LIMIT 37 4.1.1 TEST PROCEDURE 37 4.1.2 DEVIATION FROM STANDARD 37 4.1.3 TEST SETUP 37 4.1.4 EUT OPERATION CONDITIONS 37 4.1.5 TEST RESULTS 38 5 . BANDWIDTH TEST 46 5.1 APPLIED PROCEDURES / LIMIT 46 5.1.1 TEST PROCEDURE 46 Page 4 of 66 Report No.: NTEK-2013NT0724802F Table of Contents Page 5.1.2 EUT OPERATION CONDITIONS 46 5.1.3 TEST RESULTS 47 6 . PEAK OUTPUT POWER TEST 55 6.1 APPLIED PROCEDURES / LIMIT 55 6.1.1 TEST PROCEDURE 55 6.1.2 DEVIATION FROM STANDARD 55 6.1.3 TEST SETUP 55 6.1.4 EUT OPERATION CONDITIONS 55 6.1.5 TEST RESULTS 56 7 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 57 7.1 DEVIATION FROM STANDARD 57 7.2 TEST SETUP 57 7.3 EUT OPERATION CONDITIONS 57 7.4 TEST RESULTS 58 8 . ANTENNA REQUIREMENT 64 8.1 STANDARD REQUIREMENT 64 8.2 EUT ANTENNA 64 9 . EUT TEST PHOTO 65 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 66 Report No.: NTEK-2013NT0724802F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247 (a)(2) 6dB Bandwidth PASS 15.247 (b) Peak Output Power PASS 15.247 (c) Radiated Spurious Emission PASS 15.247 (d) Power Spectral Density PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 66 Report No.: NTEK-2013NT0724802F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add.:1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 66 Report No.: NTEK-2013NT0724802F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment KID’S TABLET Trade Name N/A Model Name YC7RD Serial Model YC7RQ, YC7RS Model Difference All the models are the same circuit and RF module, except the model names. Product Description The EUT is a KID’S TABLET. Operation Frequency: 802.11b/g/n(20MHz):2412~2462 MHz 802.11n(40MHz):2422~2452 Modulation Type: CCK/OFDM/DBPSK/DAPSK Bit Rate of Transmitter 802.11b:11/5.5/2/1 Mbps 802.11g:54/48/36/24/18/12/9/6Mbps 802.11n(20/40MHz):150/144.44/130/1 17/115.56/104/86.67/78/52/6.5Mbps Number Of Channel 802.11b/g/n20MHz:11CH 802.11n40MHz:7CH Antenna Designation: Please see Note 3. Output Power(Conducted): 802.11b: 12.75 dBm (Max.) 802.11g: 11.8…

Text truncated - open the document above for the full version.

Page 64 of 65 Report No.: NTEK-2013NT0724802F 9. EUT TEST PHOTO Radiated Measurement Photos Page 65 of 65 Report No.: NTEK-2013NT0724802F Conducted Measurement Photo