2AB3E-IPA162RECHARGEABLE SPEAKER

Important Safety Instructions ( English ) v1.6 1. Read and keep these instructions. Heed all warnings and follow all Instructions. 2. Warning (if applicable): Please refer to any important info rmation (e.g., electrical, safety, etc.) printed on the exterior bottom enclosure or rear panel before installing or operating the product. 3. Clean only with dry cloth. 4. Water and Moisture (if applicable): Do not use this apparatus near water. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Electrical equipment should NEVER be kept or stored in damp environments. 5. (If applicable) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install this equipment in a confin ed or “boxed-in” space such as a bookcase or similar unit, and maintain good ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place expose d flame sources such as lighted candles on the apparatus. 7. (If applicable) This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. 8. (If applicable) Be careful not to damage the power cord. When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Before using it again, make sure the power cord has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer. 9. Unplug this apparatus during lightning storms or when unused for long periods of time. 10. Only use attachment/accessories specified by the manufacturer. 11. (If applicable) Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Internal/External Voltage Selectors (if applicable): Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself. 13. Caution (if applicable): Danger of explosion if battery is incorr ectly replaced. Replace only with the same or equivalent type. Batteries (a battery pack or an in stalled battery) shall not be exposed to excessive heat such as sunshine, fire, etc. 14. (If applicable) Do not defeat the safety purpose of the polarized or grounding-type plug. 15. Protective earthing terminal (if applicable): The ap paratus should be connected to a mains socket outlet with a protective earthing connection. • Denmark ( Danmark ): Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. • Finland ( Suomi ): Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan. • Norway ( Norge ): Apparatet må tilkoples jordet stikkontakt. • Sweden ( Sverige ): Apparaten skall anslutas till jordat uttag. 16. For Class II apparatus only : This symbol means the equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. When servicing use only identi cal replacement parts installed by an instructed person or with the use of ready-made leads or cords. 17. Warning (if applicable): Provide an earthing connection be fore the mains plug is connected to the mains. When disconnecting the earthing connection, be sure to disconnect it after pulling the mains plug out from the mains. 18. (If applicable) Where the mains plug or an applian ce coupler is used as the disconnect device, the disconnect device shall remain readily operable . 19. Warning (if applicable): To prevent possible hearing damage, do not listen at high volume levels for long periods. 20. This apparatus is for professional use only . Intended operational climate: moderate. Safety Notices CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE D SERVICE PERSONNEL ONLY. DANGEROUS VOLTAGE : The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. INSTRUCTIONS : The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instru ctions in the literature acco mpanying this appliance. CAUTION ( for U.S.A. & CANADIAN models only ): TO PREVENT ELECTRIC SH OCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTICE CONCERNING LASER PRODUCTS : DANGER : INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOS URE TO BEAM. USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. NOTICE CONCERNING FCC REGULATIONS : You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide r easonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio freque ncy energy and, if not installed and used …

Text truncated - open the document above for the full version.

ION Audio, LLC I, the undersigned, Declaration: They are identical to each other, only except for model name, appearance in color or decorating parts and silkscreen for marketing purpose. GAME DAY PRIMETIME, GAME DAY™ PRIMETIME, iPA162 and SPORT BOOM, SPORT™ BOOM, iPA162B the difference is: SPORT BOOM, SPORT™ BOOM, iPA162B no LED (without light board), handle color is different. 1) Model No.: GAME DAY PRIMETIME 2) Model No.: GAME DAY™ PRIMETIME 3) Model No.: iPA162 4) Model No.: SPORT BOOM 5) Model No.: SPORT™ BOOM 6) Model No.: iPA162B 7) Model No.: iPA162****** (* can be 0-9, A-Z or blank) 8) Model No.: GAME************ (* can be 0-9, A-Z or blank) 9) Model No.: SPORT************ (* can be 0-9, A-Z or blank) FCC ID: 2AB3E-IPA162 Sincerely, Client’s signature : Client’s name: Hill Lien/ Director of Compliance Contact information / address: 200 Scenic View Drive, Cumberland, RI 02864, U.S.A. Telephone: 886-2-2717-2389 Fax No.: 886-2-2717-2735

DATE : 1/7/2023 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint EST Technology Co., Ltd. Address:Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864, U.S.A. <Signature> Name：Hill Lien Title： Director of Compliance Applicant Company： ION Audio, LLC

DATE : 1/7/2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AB3E-IPA162 Product Name: RECHARGEABLE SPEAKER Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name：Hill Lien Title： Director of Compliance Company：ION Audio, LLC

深圳市欧德声科技有限公司 ADD:深圳龙华区工业东路42号品创源科技园B栋501 TEL:0755-85278545 FAX:075585278546 第 2 页 共 9 页 1.1 Specifications 天线型号Antennas Type BW2.4FNX42-12B1L110 频率范围 Frequenc Range(MHz) 2400-2500 输入阻抗Input Impendence (Ω) 50Ω 电压驻波比V.S.W.R <2 增益Gain (dBi) 1.48dBi (Max) 极化形式Polarization Type 垂直Vertical 功率容量Power Capacity (w) 50 雷电保护Lingtning Protection None 工作电压DC Voltage（V） None 天线尺寸 Dimension（mm） 42x12 接口形式/Connector Type: IPEX-1 电缆型号Cable type（mm） φ1.13 电缆长度Cable length(mm) 110 辐射体Radiator None 天线颜色Color 黑色Black 重量Weight(g) None 工作温度Operating Temperature（°C） -40~80 储藏温度Storage Temperature（°C） -20~85 * * 注 注 ： ： 以 以 上 上 数 数 据 据 仅 仅 供 供 参 参 考 考 ； ； 因 因 天 天 线 线 功 功 能 能 较 较 为 为 敏 敏 感 感 ， ， 主 主 体 体 周 周 边 边 机 机 构 构 有 有 变 变 更 更 请 请 通 通 知 知 我 我 们 们 评 评 估 估 。 。 深圳市欧德声科技有限公司 ADD:深圳龙华区工业东路42号品创源科技园B栋501 TEL:0755-85278545 FAX:075585278546 第 3 页 共 9 页 1.2 Antenna Picture （定制客户中间连接线长度定制，天线形状定制） * * 注 注 ： ： 因 因 天 天 线 线 功 功 能 能 较 较 为 为 敏 敏 感 感 ， ， 主 主 体 体 周 周 边 边 机 机 构 构 有 有 变 变 更 更 请 请 通 通 知 知 我 我 们 们 评 评 估 估 。 。 上图型号：BW2.4FNX42-12B1图片仅供参考 深圳市欧德声科技有限公司 ADD:深圳龙华区工业东路42号品创源科技园B栋501 TEL:0755-85278545 FAX:075585278546 第 4 页 共 9 页 2. E E l l e e c c t t r r i i c c a a l l S S p p e e c c i i f f i i c c a a t t i i o o n n 2.1 Test Equipment A. VSWR and input impedance: Agilent 8753/E5071 Network Analyzer B. Antenna gain and efficiency: ETS three-dimensional anechoic chamber 2.2 Test Setup 2.2.1 Frequency Range 2.2.2 VSWR Step 1: The antenna is arranged on the customer provided test fixture. Step 2: The VSWR of the antenna is measured via Agilent 8720/8753 Network Analyzer (see figure. 1). Figure.1 深圳市欧德声科技有限公司 ADD:深圳龙华区工业东路42号品创源科技园B栋501 TEL:0755-85278545 FAX:075585278546 第 5 页 共 9 页 2.2.3 Radiation pattern and Gain A. The 3D chamber provides less than -40dB reflectivity from 800MHz to 6GHz and a 40cm diameter spherical quiet zone. The measurement results are calibrated using both dipoles and standard gain horns (see figure. 2). B. The antenna under tested is arranged in the turned table and a decoupling sleeve is used to reduce feed line radiation (see figure. 3). C. The measured results of the radiation patterns and antenna gain are obtained from the control system and showed on the monitor (see figure. 4 and 5). Figure.2 Figure.3 Figure.4 Figure.5 深圳市欧德声科技有限公司 ADD:深圳龙华区工业东路42号品创源科技园B栋501 TEL:0755-85278545 FAX:075585278546 第 6 页 共 9 页 3. Performance Data 3.1 Passive data VSWR（电压驻波比）/Return Loss（回波损耗）/Smith Chart（史密斯圆图）增益数据表和测试结果2D/3D图 * * 注 注 ： ： 以 以 上 上 为 为 实 实 测 测 数 数 据 据 ， ， 仅 仅 供 供 参 参 考 考 ； ； 因 因 天 天 线 线 功 功 能 能 较 较 为 为 敏 敏 感 感 ， ， 主 主 体 体 周 周 边 边 机 机 构 构 有 有 变 变 更 更 请 请 通 通 知 知 我 我 们 们 评 评 估 估 。 。

External Photos M/N: GAME DAY PRIMETIME External Photos M/N: GAME DAY PRIMETIME External Photos M/N: GAME DAY PRIMETIME External Photos M/N: GAME DAY PRIMETIME External Photos M/N: GAME DAY PRIMETIME

Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME Antenna Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME Internal Photos M/N: GAME DAY PRIMETIME

FCC ID: 2AB3E-IPA162 EST Technology Co. ,Ltd Report No. ESTE-R2212350 Page 1 of 5 FCC 47 CFR MPE REPORT ION Audio, LLC RECHARGEABLE SPEAKER Model Number: GAME DAY PRIMETIME Additional Model: GAME DAY™ PRIMETIME, iPA162, SPORT BOOM, SPORT™ BOOM, iPA162B, iPA162******, GAME************, SPORT************ (* can be 0-9, A-Z or blank) FCC ID: 2AB3E-IPA162 Applicant: ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864 U.S.A. Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2212350 Date of Test: Oct. 28~Dec. 29, 2022 Date of Report: Dec. 30, 2022 FCC ID: 2AB3E-IPA162 EST Technology Co. ,Ltd Report No. ESTE-R2212350 Page 2 of 5 Maximum Permissible Exposure 1. Applicable Standards Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. 1.1. Limits for Maximum Permissible Exposure (MPE) (a) Limits for Occupational/Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-10000 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-10000 1.o 30 Note: f=frequency in MHz; *Plane-wave equivalent power density FCC ID: 2AB3E-IPA162 EST Technology Co. ,Ltd Report No. ESTE-R2212350 Page 3 of 5 1.2. MPE Calculation Method E (V/m) = d G × P × 30 Power Density: Pd (W/m 2 ) = 377 E 2 E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 d × 377 G × P × 30 From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained FCC ID: 2AB3E-IPA162 EST Technology Co. ,Ltd Report No. ESTE-R2212350 Page 4 of 5 2. Conducted Power Result Mode Frequency (MHz) Peak output power (dBm) Peak output power (mW) GFSK 2402 4.95 3.1261 2441 2.78 1.8967 2480 0.89 1.2274 π/4-DQPSK 2402 4.73 2.9717 2441 2.52 1.7865 2480 0.82 1.2078 8-DPSK 2402 4.71 2.9580 2441 2.56 1.8030 2480 0.71 1.1776 BLE 2402 4.61 2.8907 2440 2.23 1.6711 2480 0.38 1.0914 FCC ID: 2AB3E-IPA162 EST Technology Co. ,Ltd Report No. ESTE-R2212350 Page 5 of 5 3. Calculated Result and Limit Mode Peak output power (dBm) Target power （dBm ） MAX Target power （dBm） Antenna gain Power Density (S) (mW /cm2) Limited of Power Density (S) (mW /cm2) Test Result (dBi) (Linear ) 2.4G Band GFSK 4.95 4±1 5 1.48 1.4060 0.0009 1 Complies π/4 DQPSK 4.73 4±1 5 1.48 1.4060 0.0009 1 Complies 8-DPSK 4.71 4±1 5 1.48 1.4060 0.0009 1 Complies BLE 4.61 4±1 5 1.48 1.4060 0.0009 1 Complies End of Test Report

FCC ID: 2AB3E-IPA162 EST Technology Co., Ltd Report No.ESTE-R2212349 Page 1 of 70 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of ION Audio, LLC RECHARGEABLE SPEAKER Model Number: GAME DAY PRIMETIME Additional Model: GAME DAY™ PRIMETIME, iPA162, SPORT BOOM, SPORT™ BOOM, iPA162B, iPA162******, GAME************, SPORT************ (* can be 0-9, A-Z or blank) FCC ID: 2AB3E-IPA162 Applicant : ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864 U.S.A. Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2212349 Date of Test: Oct. 28~Dec. 29, 2022 Date of Report: Dec. 30, 2022 FCC ID: 2AB3E-IPA162 EST Technology Co., Ltd Report No.ESTE-R2212349 Page 2 of 70 TABLE OF CONTENTS Description Page TEST REPORT VERIFICATION......................................................................................................................... 3 1. GENERAL INFORMATION ................................................................................................................. 5 1.1. Description of Device (EUT) ........................................................................................................... 5 1.2. Antenna Information ........................................................................................................................ 5 1.3. Information of RF Cable .................................................................................................................. 5 2. SUMMARY OF TEST ......................................................................................................................... 6 2.1. Summary of test result ...................................................................................................................... 6 2.2. Test Facilities ................................................................................................................................... 7 2.3. Measurement uncertainty ................................................................................................................. 8 2.4. Assistant equipment used for test ..................................................................................................... 8 2.5. Block Diagram ................................................................................................................................. 8 2.6. Test Mode ......................................................................................................................................... 9 2.7. Power Setting of Test Software ........................................................................................................ 9 2.8. Duty Cycle ...................................................................................................................................... 10 2.9. Channel List ................................................................................................................................... 11 2.10. Test Equipment List ....................................................................................................................... 12 3. 6DB BANDWIDTH .......................................................................................................................... 14 3.1. Limit ............................................................................................................................................... 14 3.2. Test Setup ....................................................................................................................................... 14 3.3. Spectrum Analyzer Setting ............................................................................................................. 14 3.4. Test Procedure ................................................................................................................................ 14 3.5. Test Result ...................................................................................................................................... 14 4. MAXIMUM PEAK OUTPUT POWER ................................................................................................. 15 4.1. Limit ............................................................................................................................................... 15 4.2. Test Setup ....................................................................................................................................... 15 4.3. Spectrum Analyzer Setting ............................................................................................................. 15 4.4. Test Procedure ................................................................................................................................ 15 4.5. Test Result ...................................................................................................................................... 15 5. POWER SPECTRAL DENSITY .......................................................................................................... 16 5.1. Limit ............................................................................................................................................... 16 5.2. Test Setup ....................................................................................................................................... 16 5.3. Spectrum Analyzer Setting ............................................................................................................. 16 5.4. Test Procedure ................................................................................................................................ 16 5.5. Test Result ...................................................................................................................................... 16 6. CONDUCTED BAND EDGE ..............................................................................................…

Text truncated - open the document above for the full version.

Conducted Test Radiated Test (30-1000 MHz) Radiated Test (Above 1GHz)