2AB3E-IPA163Bluetooth device

Battery Fuse Rating / Capacidad nominal del fusible de la batería / Calibre de fusible de la batterie : T3.15AL/250V Important Safety Instructions ( English ) v1.6 1. Read and keep these instructions. Heed all warnings and follow all Instructions. 2. Warning (if applicable): Please refer to any important info rmation (e.g., electrical, safety, etc.) printed on the exterior bottom enclosure or rear panel before installing or operating the product. 3. Clean only with dry cloth. 4. Water and Moisture (if applicable): Do not use this apparatus near water. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Electrical equipment should NEVER be kept or stored in damp environments. 5. (If applicable) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install this equipment in a confin ed or “boxed-in” space such as a bookcase or similar unit, and maintain good ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place expose d flame sources such as lighted candles on the apparatus. 7. (If applicable) This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. 8. (If applicable) Be careful not to damage the power cord. When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Before using it again, make sure the power cord has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer. 9. Unplug this apparatus during lightning storms or when unused for long periods of time. 10. Only use attachment/accessories specified by the manufacturer. 11. (If applicable) Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Internal/External Voltage Selectors (if applicable): Internal or external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself. 13. Caution (if applicable): Danger of explosion if battery is incorr ectly replaced. Replace only with the same or equivalent type. Batteries (a battery pack or an in stalled battery) shall not be exposed to excessive heat such as sunshine, fire, etc. 14. (If applicable) Do not defeat the safety purpose of the polarized or grounding-type plug. 15. Protective earthing terminal (if applicable): The ap paratus should be connected to a mains socket outlet with a protective earthing connection. • Denmark ( Danmark ): Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. • Finland ( Suomi ): Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan. • Norway ( Norge ): Apparatet må tilkoples jordet stikkontakt. • Sweden ( Sverige ): Apparaten skall anslutas till jordat uttag. 16. For Class II apparatus only : This symbol means the equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. When servicing use only identi cal replacement parts installed by an instructed person or with the use of ready-made leads or cords. 17. Warning (if applicable): Provide an earthing connection be fore the mains plug is connected to the mains. When disconnecting the earthing connection, be sure to disconnect it after pulling the mains plug out from the mains. 18. (If applicable) Where the mains plug or an applian ce coupler is used as the disconnect device, the disconnect device shall remain readily operable . 19. Warning (if applicable): To prevent possible hearing damage, do not listen at high volume levels for long periods. 20. This apparatus is for professional use only . Intended operational climate: moderate. Safety Notices CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE D SERVICE PERSONNEL ONLY. DANGEROUS VOLTAGE : The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. INSTRUCTIONS : The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instru ctions in the literature acco mpanying this appliance. CAUTION ( for U.S.A. & CANADIAN models only ): TO PREVENT ELECTRIC SH OCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTICE CONCERNING LASER PRODUCTS : DANGER : INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOS URE TO BEAM. USE OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. NOTICE CONCERNING FCC REGULATIONS : You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide r easonable protection against harmful interference in a residentia…

Text truncated - open the document above for the full version.

ION Audio, LLC I, the undersigned, Declaration: They are identical to each other, only except for model name, appearance in color or decorating parts and silkscreen for marketing purpose. 1) Model No.: PARTY BOOM™ PLUS 2) Model No.: iPA163 3) Model No.: PARTY************ ("*" is a variable, it can be 0-9, A-Z or blank) 4) Model No.: iPA163**** ("*" is a variable, it can be 0-9, A-Z or blank) FCC ID: 2AB3E-IPA163 Sincerely, Client’s signature : Client’s name: Hill Lien/ Director of Compliance Contact information / address: 200 Scenic View Drive, Cumberland, RI 02864, U.S.A. Telephone: 886-2-2717-2389 Fax No.: 886-2-2717-2735

DATE : 1/7/2023 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint EST Technology Co., Ltd. Address:Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864, U.S.A. <Signature> Name：Hill Lien Title： Director of Compliance Applicant Company： ION Audio, LLC

DATE : 1/7/2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AB3E-IPA163 Product Name: Bluetooth device Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name：Hill Lien Title： Director of Compliance Company：ION Audio, LLC

M a Add Shiy Te anufacture dress of an yan Town, chnology ： er of Anten ntenna m , Baoan D IPA16 Type：P Leng Widt ：FR4&Co nna：SHE anufactur istrict, She 63 BT ANT PCB On Bo gth：20.55 th：5.80m over Resis ENZHEN FE rer：Fend enzhen Ci T SPEC oard ANT 5mm mm stance We ENDA TEC a Hi-Tech ty，Gua n elding Oil CHNOLOGY Park, Zho ngdong，C Y CO., LTD oushi Road China D. d, SWR R & Returnn Loss F 2 2 2 2 2 2 2 2 2 2 2 Frequency (MHz) 2400 MHz 2410 MHz 2420 MHz 2430 MHz 2440 MHz 2450 MHz 2460 MHz 2470 MHz 2480 MHz 2490 MHz 2500 MHz Efficciency & G Efficiency (%) 37.46 36.92 36.48 36.95 37.32 37.87 38.26 37.75 37.54 36.69 36.51 Gain y Gain (dBi) 1.55 1.53 1.50 1.56 1.65 1.68 1.78 1.69 1.67 1.54 1.50

External Photos M/N: PARTY BOOM ™ PLUS External Photos M/N: PARTY BOOM ™ PLUS External Photos M/N: PARTY BOOM ™ PLUS External Photos M/N: PARTY BOOM ™ PLUS External Photos M/N: PARTY BOOM ™ PLUS

版本：A/4

Internal Photos M/N: PARTY BOOM ™ PLUS Internal Photos M/N: PARTY BOOM ™ PLUS Internal Photos M/N: PARTY BOOM ™ PLUS Internal Photos M/N: PARTY BOOM ™ PLUS Internal Photos M/N: PARTY BOOM ™ PLUS Bluetooth Antenna Internal Photos M/N: PARTY BOOM ™ PLUS Internal Photos M/N: PARTY BOOM ™ PLUS

FCC ID: 2AB3E-IPA163 EST Technology Co. ,Ltd Report No. ESTE-R2212304 Page 1 of 5 FCC 47 CFR MPE REPORT ION Audio, LLC PORTABLE BLUETOOTH ® -ENABLED SPEAKER WITH LIGHTS AND PREMIUM WIDE SOUND Model Number: PARTY BOOM ™ PLUS Additional Model: iPA163, PARTY************, iPA163**** FCC ID: 2AB3E-IPA163 Applicant: ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864 U.S.A. Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2212304 Date of Test: Dec. 10~24, 2022 Date of Report: Dec. 28, 2022 FCC ID: 2AB3E-IPA163 EST Technology Co. ,Ltd Report No. ESTE-R2212304 Page 2 of 5 Maximum Permissible Exposure 1. Applicable Standards Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. 1.1. Limits for Maximum Permissible Exposure (MPE) (a) Limits for Occupational/Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-10000 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-10000 1.o 30 Note: f=frequency in MHz; *Plane-wave equivalent power density FCC ID: 2AB3E-IPA163 EST Technology Co. ,Ltd Report No. ESTE-R2212304 Page 3 of 5 1.2. MPE Calculation Method E (V/m) = d G×P×30 Power Density: Pd (W/m 2 ) = 377 E 2 E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 d×377 G×P×30 From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained FCC ID: 2AB3E-IPA163 EST Technology Co. ,Ltd Report No. ESTE-R2212304 Page 4 of 5 2. Conducted Power Result Mode Frequency (MHz) Peak output power (dBm) Peak output power (mW) GFSK 2402 3.43 2.2029 2441 2.98 1.9861 2480 2.93 1.9634 π/4-DQPSK 2402 3.93 2.4717 2441 3.42 2.1979 2480 3.36 2.1677 8-DPSK 2402 4.38 2.7416 2441 3.70 2.3442 2480 3.48 2.2284 BLE 1M 2402 3.19 2.0845 2440 2.78 1.8967 2480 2.65 1.8408 BLE 2M 2412 3.31 2.1429 2440 2.90 1.9498 2480 2.75 1.8836 FCC ID: 2AB3E-IPA163 EST Technology Co. ,Ltd Report No. ESTE-R2212304 Page 5 of 5 3. Calculated Result and Limit Mode Peak output power (dBm) Target power （dBm） MAX Target power (dBm) Antenna gain Power Density (S) (mW /cm 2 ) Limited of Power Density (S) (mW /cm 2 ) Test Result (dBi) (Linear) 2.4G Band GFSK 3.43 3±1 4 1.781.5066 0.0008 1 Complies π/4-DQPSK 3.93 3±1 4 1.781.5066 0.0008 1 Complies 8-DPSK 4.38 4±1 5 1.781.5066 0.0009 1 Complies BLE 3.31 3±1 4 1.781.5066 0.0008 1 Complies End of Test Report

FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 1 of 82 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of ION Audio, LLC PORTABLE BLUETOOTH ® -ENABLED SPEAKER WITH LIGHTS AND PREMIUM WIDE SOUND Model Number: PARTY BOOM ™ PLUS Additional Model: iPA163, PARTY************, iPA163**** FCC ID: 2AB3E-IPA163 Applicant : ION Audio, LLC Address: 200 Scenic View Drive, Cumberland, RI 02864 U.S.A. Prepared By: EST Technology Co., Ltd. Chilingxiang, Qishantou, Santun, Houjie, Dongguan, Guangdong, China Tel: 86-769-83081888-808 Report Number: ESTE-R2212302 Date of Test: Dec. 10~24, 2022 Date of Report: Dec. 28, 2022 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 2 of 82 TABLE OF CONTENTS Description Page TEST REPORT VERIFICATION......................................................................................................................... 3 1. GENERAL INFORMATION ................................................................................................................. 5 1.1. Description of Device (EUT) ........................................................................................................... 5 1.2. Antenna Information ........................................................................................................................ 5 1.3. Information of RF Cable .................................................................................................................. 5 2. SUMMARY OF TEST ......................................................................................................................... 6 2.1. Summary of test result ...................................................................................................................... 6 2.2. Test Facilities ................................................................................................................................... 7 2.3. Measurement uncertainty ................................................................................................................. 8 2.4. Assistant equipment used for test ..................................................................................................... 8 2.5. Block Diagram ................................................................................................................................. 8 2.6. Test mode ......................................................................................................................................... 9 2.7. Channel List ................................................................................................................................... 10 2.8. Power Setting of Test Software ...................................................................................................... 10 2.9. Test Equipment ............................................................................................................................... 11 3. MAXIMUM PEAK OUTPUT POWER ................................................................................................. 13 3.1. Limit ............................................................................................................................................... 13 3.2. Test Setup ....................................................................................................................................... 13 3.3. Spectrum Analyzer Setting ............................................................................................................. 13 3.4. Test Procedure ................................................................................................................................ 13 3.5. Test Result ...................................................................................................................................... 13 4. 20 DB BANDWIDTH ....................................................................................................................... 14 4.1. Limit ............................................................................................................................................... 14 4.2. Test Setup ....................................................................................................................................... 14 4.3. Spectrum Analyzer Setting ............................................................................................................. 14 4.4. Test Procedure ................................................................................................................................ 14 4.5. Test Result ...................................................................................................................................... 14 5. CARRIER FREQUENCY SEPARATION .............................................................................................. 15 5.1. Limit ............................................................................................................................................... 15 5.2. Test Setup ....................................................................................................................................... 15 5.3. Spectrum Analyzer Setting ............................................................................................................. 15 5.4. Test Procedure ................................................................................................................................ 15 5.5. Test Result ...................................................................................................................................... 15 6. NUMBER OF HOPPING CHANNEL .................................................................................................. 16 6.1. Limit ............................................................................................................................................... 16 6.2. Test Setup ............................…

Text truncated - open the document above for the full version.

FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 56 of 82 Appendix F: Reference level measurement Test Result Test Mode Antenna Freq(MHz) Max.Point[MHz] Result[dBm] DH5 Ant1 2402 2401.83 3.00 2441 2440.83 2.47 2480 2479.83 2.39 2DH5 Ant1 2402 2401.83 2.77 2441 2440.83 2.24 2480 2479.83 2.24 3DH5 Ant1 2402 2401.83 2.91 2441 2440.83 2.42 2480 2479.83 2.26 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 57 of 82 Test Graphs DH5_Ant1_2402 DH5_Ant1_2441 DH5_Ant1_2480 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 58 of 82 2DH5_Ant1_2402 2DH5_Ant1_2441 2DH5_Ant1_2480 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 59 of 82 3DH5_Ant1_2402 3DH5_Ant1_2441 3DH5_Ant1_2480 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 60 of 82 Appendix G: Band edge measurements Test Result Test Mode Antenna Ch Name Freq(MHz) Ref Level [dBm] Result [dBm] Limit [dBm] Verdict DH5 Ant1 Low 2402 3.00 -48.14 ≤-17 PASS High 2480 2.39 -48.55 ≤-17.61 PASS Low Hop_2402 1.64 -51.15 ≤-18.36 PASS High Hop_2480 1.78 -49.48 ≤-18.22 PASS 2DH5 Ant1 Low 2402 2.77 -48.43 ≤-17.23 PASS High 2480 2.24 -50.2 ≤-17.76 PASS Low Hop_2402 -0.58 -50.82 ≤-20.58 PASS High Hop_2480 1.09 -50.1 ≤-18.91 PASS 3DH5 Ant1 Low 2402 2.91 -48.97 ≤-17.09 PASS High 2480 2.26 -49.64 ≤-17.74 PASS Low Hop_2402 0.93 -50.7 ≤-19.07 PASS High Hop_2480 -0.17 -50.48 ≤-20.17 PASS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 61 of 82 Test Graphs DH5_Ant1_Low_2402 DH5_Ant1_High_2480 DH5_Ant1_Low_Hop_2402 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 62 of 82 DH5_Ant1_High_Hop_2480 2DH5_Ant1_Low_2402 2DH5_Ant1_High_2480 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 63 of 82 2DH5_Ant1_Low_Hop_2402 2DH5_Ant1_High_Hop_2480 3DH5_Ant1_Low_2402 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 64 of 82 3DH5_Ant1_High_2480 3DH5_Ant1_Low_Hop_2402 3DH5_Ant1_High_Hop_2480 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 65 of 82 Appendix H: Conducted Spurious Emission Test Result Test Mode Antenna Freq(MHz) Freq Range [MHz] Ref Level [dBm] Result [dBm] Limit [dBm] Verdict DH5 Ant1 2402 30~26500 3.00 -41.72 ≤-17 PASS 2441 30~26500 2.47 -42.53 ≤-17.53 PASS 2480 30~26500 2.39 -42.99 ≤-17.61 PASS 2DH5 Ant1 2402 30~26500 -0.58 -42.86 ≤-20.58 PASS 2441 30~26500 2.24 -42.66 ≤-17.76 PASS 2480 30~26500 2.24 -43.24 ≤-17.76 PASS 3DH5 Ant1 2402 30~26500 2.91 -42.25 ≤-17.09 PASS 2441 30~26500 2.42 -43.06 ≤-17.58 PASS 2480 30~26500 2.26 -43.03 ≤-17.74 PASS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 66 of 82 Test Graphs DH5_Ant1_2402_30~26500 DH5_Ant1_2441_30~26500 DH5_Ant1_2480_30~26500 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 67 of 82 2DH5_Ant1_2402_30~26500 2DH5_Ant1_2441_30~26500 2DH5_Ant1_2480_30~26500 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 68 of 82 3DH5_Ant1_2402_30~26500 3DH5_Ant1_2441_30~26500 3DH5_Ant1_2480_30~26500 FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 69 of 82 14. TEST SETUP PHOTO Conducted Test FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 70 of 82 Radiated Test (Below 1GHz) Radiated Test (Above 1GHz) FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 71 of 82 15. EUT PHOTO External Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 72 of 82 External Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 73 of 82 External Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 74 of 82 External Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 75 of 82 External Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 76 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 77 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 78 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 79 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 80 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS Bluetooth Antenna FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 81 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS FCC ID: 2AB3E-IPA163 EST Technology Co., Ltd Report No. ESTE-R2212302 Page 82 of 82 Internal Photos M/N: PARTY BOOM ™ PLUS End of Test Report

Conducted Test Radiated Test (30-1000 MHz) Radiated Test (Above 1GHz)