2AB879886WiFi Module

/ 5 GHz high-power 802.11a/n/ac mini PCIe card based on QCA9886 AWMC9886PH AWMC9886PH is a single-band, high-power 802.11ac module with MMCX antenna connectors AWMC9886PH is fully compliant with IEEE 802.11ac and 802.11a/n standards, supports 2T2R antenna configuration, MU-MIMO with 2 spatial streams and up to 23.5dBm (223.87mW) transmit power The QCA9886 is a highly integrated WLAN SOC implementing half-duplex OFDM supporting up to 867 Mbps for 802.11ac 80 MHz channel width operation in 5 GHz band. Official support in open source driver for Linux, support in OpenWrt system and adoption of MMCX antenna connectors will help kick off your next reliable WiFi project launch. Key features Designed for ALFA Network N2Q 1 2 3 4 5 Qualcomm™ QCA9886 broadband radio 1 Skyworks™ SKY85728-11 FEM with high-power PA 2 2× MMCX antenna connectors 3 Full body metal shielding design with heatsink 4 PCI Express 1.1 interface 5 © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw AWMC9886PH that can use for Indoor AP used / AWMC9886PHSpecifications ChipsetQualcomm™ QCA9886 IEEE 802.11 standardsa/n/ac Frequency5 GHz Data rate 802.11ac: 867 Mbps 80 2.11n: 300 Mbps TX power23 .5dBm (223.8mW ) Antenna connectors2× MMCX InterfacePCIe x1 Operating systemsLinux Form factorfull-size mini PCIe Operating humidity10 % ~ 90 % RH, non-condensing Operating temperatureTBA Dimensions30 × 51 × 9.2 mm (with heatsink) © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210 331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw / AWMC9886PHmini PCIe connector pinout TopBottom 1 PCIe WAKEn3.3 V2 3COEX1GND4 5 NCNC6 7 P CIe CLKREQnNC8 9 GNDNC10 11P CIe REFCLK-NC12 13P CIe REFCLK+NC14 15GNDNC16 17 N CGND18 19N CPCIe W_DISABLEn20 21 G NDPCIe PERSTn22 23PCIe PERn0NC24 25PCIe PERp0GND26 27GNDNC28 29G NDNC30 31P CIe PETn0NC32 33PCIe PETp0GND34 35GNDNC36 37 NCNC38 39NCGND40 41N CNC4 2 43GNDWLAN LED44 455 V NC46 475 V NC48 49 5 V GND50 515 V 3. 3 V52 additional 5 V power supply is requiredfor correct operation Mechanicalkey 1 1 1 1 1) © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210 331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw / AWMC9886PHProduct pictures © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210 331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw / AWMC9886PHProduct pictures (cont.) © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210 331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw / AWMC9886PHProduct pictures (cont.) © ALFA Network Inc. / AWMC9886PH datasheet ver. 20210 331 Specificationsand description may change at any time without prior notice [email protected] www.alfa.com.tw    9&&$' 9&&  &  ŶLJŚĂŶŐĞƐŽƌŵŽĚŝĨŝĐĂƚŝŽŶƐŶŽƚĞdžƉƌĞƐƐůLJĂƉƉƌŽǀĞĚďLJƚŚĞƉĂƌƚLJ ƌĞƐƉŽŶƐŝďůĞĨŽƌĐŽŵƉůŝĂŶĐĞĐŽƵůĚǀŽŝĚƚŚĞƵƐĞƌΖƐĂƵƚŚŽƌŝƚLJƚŽŽƉĞƌĂƚĞƚŚĞ ĞƋƵŝƉŵĞŶƚ͘ dŚŝƐĚĞǀŝĐĞĐŽŵƉůŝĞƐǁŝƚŚWĂƌƚϭρŽĨƚŚĞ&ZƵůĞƐ͘KƉĞƌĂƚŝŽŶŝƐƐƵďũĞĐƚƚŽƚŚĞ ĨŽůůŽǁŝŶŐƚǁŽĐŽŶĚŝƚŝŽŶƐ͗ U  $ &4  $  &*  * $ + U  $ & $$  4  * $ $   $  * $  &4 $     '+  S&         *  $&4   & *  $ >   $       !, *  99 0 +   &            $   &*  * $     '+  S&         $   * S $4  4  *        $$ $    $' &4 $  &*  * $   $&&$'+          * $   $$    '$ '+ 5*  S&    $  &*  * $       $ ' $ $    &  4    S&  V      $     4  $ $   * $ 4   & *  * &  J U0     $  $    + U5$     '     S&   $  + U9 $  S&        $ $ V  * &   $  $   $ $ + U9      %  $  CK  $$ *  + This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. >ŝƐƚŽĨĂƉƉůŝĐĂďůĞ&ƌƵůĞƐ &Zκϳ&WZdϭρ^hWZdEŚĂƐďĞĞŶŝŶǀĞƐƚŝŐĂƚĞĚ͘/ƚŝƐĂƉƉůŝĐĂďůĞƚŽƚŚĞ ŵŽĚƵůĂƌ͘ ^ƉĞĐŝĨŝĐŽƉĞƌĂƚŝŽŶĂůƵƐĞĐŽŶĚŝƚŝŽŶƐ dŚŝƐŵŽĚƵůĞŝƐƐƚĂŶĚͲĂůŽŶĞŵŽĚƵůĂƌ͘/ĨƚŚĞĞŶĚƉƌŽĚƵĐƚǁŝůůŝŶǀŽůǀĞƚŚĞDƵůƚŝƉůĞƐŝŵƵůƚĂŶĞŽƵƐůLJ ƚƌĂŶƐŵŝƚƚŝŶŐĐŽŶĚŝƚŝŽŶŽƌĚŝĨĨĞƌĞŶƚŽƉĞƌĂƚŝŽŶĂůĐŽŶĚŝƚŝŽŶƐĨŽƌĂƐƚĂŶĚͲĂůŽŶĞŵŽĚƵůĂƌ ƚƌĂŶƐŵŝƚƚĞƌŝŶ ĂŚŽƐƚ͕ŚŽƐƚŵĂŶƵĨĂĐƚƵƌĞƌŚĂǀĞƚŽĐŽŶƐƵůƚǁŝƚŚŵŽĚƵůĞŵĂŶƵĨĂĐƚƵƌĞƌĨŽƌƚŚĞ ŝŶƐƚĂůůĂƚŝŽŶŵĞƚŚŽĚŝŶĞŶĚƐLJƐƚĞŵ͘ >ŝŵŝƚĞĚŵŽĚƵůĞƉƌŽĐĞĚƵƌĞƐEŽƚĂƉƉůŝĐĂďůĞ dƌĂĐĞĂŶƚĞŶŶĂĚĞƐŝŐŶƐEŽƚĂƉƉůŝĐĂďůĞ Z&ĞdžƉŽƐƵƌĞĐŽŶƐŝĚĞƌĂƚŝŽŶƐ dŽŵĂŝŶƚĂŝŶĐŽŵƉůŝĂŶĐĞǁŝƚŚ&͛ƐZ&džƉŽƐƵƌĞŐƵŝĚĞůŝŶĞƐ͕ƚŚŝƐĞƋƵŝƉŵĞŶƚƐŚŽƵůĚďĞŝŶƐƚĂůůĞĚ ĂŶĚŽƉĞƌĂƚĞĚǁŝƚŚŵŝŶŝŵƵŵĚŝƐƚĂŶĐĞŽĨϮϬĐŵĨƌŽŵLJŽƵƌďŽĚLJ͘ ŶƚĞŶŶĂƐ dŚŝƐƌĂĚŝŽƚƌĂŶƐŵŝƚƚĞƌ&/͗2AB879886ŚĂƐďĞĞŶĂƉƉƌŽǀĞĚďLJ&ĞĚĞƌ ĂůŽŵŵƵŶŝĐĂƚŝŽŶƐ ŽŵŵŝƐƐŝŽŶƚŽŽƉĞƌĂƚĞǁŝƚŚƚŚĞĂŶƚĞŶŶĂƚLJƉĞƐůŝƐƚĞĚďĞůŽǁ͕ǁŝƚŚƚŚĞŵĂdžŝŵƵŵƉĞƌŵŝƐƐŝďůĞŐĂŝŶ ŝŶĚŝĐĂƚĞĚ͘ŶƚĞŶŶĂƚLJƉĞƐŶŽƚŝŶĐůƵĚĞĚŝŶƚŚŝƐůŝƐƚƚŚĂƚŚĂǀĞĂŐĂŝŶŐƌĞĂƚĞƌƚŚĂŶƚŚĞŵĂdžŝŵƵŵŐĂŝŶ ŝŶĚŝĐĂƚĞĚĨŽƌĂŶLJƚLJƉĞůŝƐƚĞĚĂƌĞƐƚƌŝĐƚůLJƉƌŽŚŝďŝƚĞĚĨŽƌƵƐĞǁŝƚŚƚŚŝƐĚĞǀŝĐĞ͘ An t enna type Maximu m Antenna gain 'LSROHAntenna 5 dBi >ĂďĞůĂŶĚĐŽŵƉůŝĂŶĐĞŝŶĨŽƌŵĂƚŝŽŶ dŚĞĨŝŶĂůĞŶĚƉƌŽĚƵĐƚŵƵƐƚďĞůĂďĞůĞĚŝŶĂǀŝƐŝďůĞĂƌĞĂ ǁŝƚŚƚŚĞĨŽůůŽǁŝŶŐΗŽŶƚĂŝŶƐ& /͗2AB879 886 ͟ Information on test modes and addi…

Text truncated - open the document above for the full version.

Iconnect Add: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist.,Taipei City,Taiwan Tel:886-2-27968477 Fax:886-2-27968478 Email: [email protected] Date: 2026-04-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, Iconnect, hereby authorize Shenzhen Accurate Technology Co., Ltd. to act as a laboratory for testing and test report generation for the following project(s): (Product description: WiFi Module, Model name: AWMC9886PH,FCC ID:2AB879886) The product only supports 5G Wi-Fi: 5150-5250MHz,802.11 a/n20/n40/ac20/ac40/ac80 the others were disabled by software and the end user doesn’t have the capacity to activate it . Sincerely, S ignature: Printed Name: Johnson Wang Title: Manager

Iconnect Add: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist., Taipei City, Taiwan Tel: 886-2-27968477 Fax: 886-2-27968478 Email: [email protected] ATTESTATION STATEMENT Date: 2026-04-03 FEDERAL COM MUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(5)(i), (ii) Filing FCC ID: 2AB879886 Iconnect, certifies t hat t he equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment a uthorization pursuant to section 2.903 of the FCC rules. And Iconnect, certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Iconnect (“the applicant”) certifies that our product does not use Kaspersky's software information. Sincerely, Printed name: Johnson Wang Title: Manager Signature:

U.S. AGENT LETTER OF ATTESTATION Date: FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: Iconnect certifies that, as of the date of the filing of the application, Y5Shop LLc. is our designated U.S. agent for service of process for the above referenced FCC ID. Iconnect accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Y5Shop LLc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Y5Shop LLc. Address: 2725 AUTUMN LN,FRISCO,TEXAS,USA FRN: 0033834391 Tel.: 469 636 2888 Email: [email protected] Signed by (printed name): Wang Chiang-Sheng Signature: Applicant: Iconnect Add: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist., Taipei City, Taiwan FRN:0023545262 Tel: 886-2-27968477 Fax: 886-2-27968478 Email: [email protected] Signed by Printed name: Johnson Wang Signature:

Iconnect Add: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist., Taipei City, Taiwan Tel: 886-2-27968477 Fax: 886-2-27968478 Email: [email protected] FCC Authorization Date: 2026-04-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , Iconnect, Hereby authorizes Shenzhen Accurate Technology Co., Ltd.to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, h ereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Dr ug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed name: Johnson Wang T itle: Manager QA-FR-170 -B

QA-FR-171-A Iconnect Add: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist., Taipei City, Taiwan Tel: 886-2-27968477 Fax: 886-2-27968478 Email: [email protected] FCC Confidential Authorization Date:2026-04-03 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID:2AB879886 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Iconnect, hereby requests long- term confidential treatment of information accompanying this application as outlined below: •Block Diagram •Schematics •Operation Description •SOFTWARE SECURITY DECLARATION FOR U-NII DEVICES The above mat erials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed name: Johnson Wang Title: Manager

Iconnect ADD: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist.,Taipei City,Taiwan TEL: 886-2-27968477 FAX: 886-2-27968478 Email: [email protected] Modular Approval Letter Date: 2026-04-03 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 W e, Iconnect, hereby request Modular Approval for Product: WiFi Module (Model number: AWMC9886PH, FCC ID: 2AB879886).The requirement of FCC 15.212 as below: Item § 15.212 RequirementY/N Comments (i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Yes The modular has RF shielding, please refer to the EUT photo. (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. Yes The modular transmitter has buffered modulation/data inputs, Buffered data inputs stage has been integrated in chip (Model: QCA9886). (iii) The modular transmitter must have its own power supply regulation. Yes The modular transmitter has its own power supply regulation. Please refer to the Block Diagram. (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Yes Comply with the antenna requirements of Section 15.203 and 15.204(c), the modular have a Dipole Antenna attached to the module, the maximum gain is 5dBi. (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, Yes The EUT was tested in a stand-alone configuration, please refer to setup photos exhibit for details. it must comply with the AC line conducted requirements found in § 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see § 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see § 15.31(i)). (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. Yes The module labeled with its own FCC ID. (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Yes Comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The necessary explanation to be complied with this requirement is contained in the user manual, and please refers to the User Manual. (viii) Radio frequency devices operating under the provisions of this part are subject to the radio frequency radiation exposure requirements specified in §§ 1.1307(b), 1.1310, 2.1091, and 2.1093 of this chapter. Yes Comply with any applicable RF exposure requirements in its final configuration. Sincerely, Signature: Johnson Wang Manager

Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT External Photos External Photos Page 1 / 3 External Photos Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT External Photos External Photos Page 2 / 3 Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT External Photos External Photos Page 3 / 3 ***** END *****

Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT Internal Photos Internal Photos Page 1 / 3 Internal Photos Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT Internal Photos Internal Photos Page 2 / 3 ANT Shenzhen Accurate Technology Co., Ltd. No.: 2604Q36815E-RF EUT Internal Photos Internal Photos Page 3 / 3 ***** END *****

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.0(2024/11/01) Page 1 of 6 TR-4-E-R052 TEST REPORT Applicant Name : Iconnect Address : No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist.,Taipei City, Taiwan Report Number : 2604Q36815E-RF FCC ID: 2AB879886 Test Standard (s) 47 CFR §2.1091 Sample Description Product Type: WiFi Module Model No.: AWMC9886PH Trade Mark: ALFA Date Received: 2026-02-26 Report Date: 2026-05-14 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2604Q36815E-RF Rev:A/4.0(2024/11/01) Page 2 of 6 TR-4-E-R052 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 3 GENERAL INFORMATION ............................................................................................................................ 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 4 OBJECTIVE ................................................................................................................................................... 4 TEST FACILITY .............................................................................................................................................. 4 RF EXPOSURE .............................................................................................................................................. 5 APPLICABLE STANDARD ................................................................................................................................. 5 RESULT ........................................................................................................................................................ 5 EXHIBIT A-EUT PHOTOGRAPHS ................................................................................................................ 6 Shenzhen Accurate Technology Co., Ltd. Report No.: 2604Q36815E-RF Rev:A/4.0(2024/11/01) Page 3 of 6 TR-4-E-R052 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision Rev.00 2604Q36815E-RF Original Report 2026-05-14 Shenzhen Accurate Technology Co., Ltd. Report No.: 2604Q36815E-RF Rev:A/4.0(2024/11/01) Page 4 of 6 TR-4-E-R052 GENERAL INFORMATION Product Description for Equipment under Test (EUT) Product WiFi Module Tested Model AWMC9886PH Frequency Range 5G Wi-Fi: 5150-5250MHz Maximum Conducted Output Power 23.31 dBm Antenna Specification # External Antenna: Ant0(Chain 0): 5 dBi, Ant1(Chain 1): 5 dBi (It is provided by the applicant.) Voltage Range # DC 3.3V from test board Sample Serial Number 3BCG-2 (For RF Conducted Test) (Assigned by ATC, Shenzhen) Sample/EUT Status Good condition Objective This test report is in accordance with Part 2-Subpart J, Part 15-Subparts C and Part 2-Subpart J, Radiofrequency Radiation Exposure of the Federal Communication Commission rules. The tests were performed in order to determine compliance with FCC §2.1091 rules. Test Facility The test site used by Shenzhen Accurate Technology Co., Ltd. to collect test data is located on the Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Accredited by American Association for Laboratory Accreditation (A2LA).The Certificate Number is 4297.01. Shenzhen Accurate Technology Co., Ltd. Report No.: 2604Q36815E-RF Rev:A/4.0(2024/11/01) Page 5 of 6 TR-4-E-R052 RF EXPOSURE Applicable Standard According to subpart 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (Minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Result Calculated Formulary: Predication of MPE limit at a given distance S = 2 4R PG  S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW). G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain. R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Mode Frequency (MHz) Antenna Gain # Tune up conducted power # Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric) (dBm) (mW) 5G Wi-Fi 5150-5250 5.0 3.16 23.50 223.87 20 0.141 1.0 Note: The tune-up power and antenna gain are declared by the applicant. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment…

Text truncated - open the document above for the full version.

1 Product Number:T Product Name: WIFI 7 Antenna 1.Specification Sample Photo A.Electrical Characteristics Frequency 2400 ~ 2500 MHz 5150 ~ 5850 MHz 5925 ~ 7125 MHz V.S.W.R.<= 2.0 @ 2400 ~ 2500 MHz <= 2.5 @ 5150 ~ 5850 MHz <= 2.5 @ 6500 MHz <= 2.5 @ 7125 MHz Efficiency ~75% Polarization Linear Impedance 50 Ohm B.Material & Mechanical Characteristics Material of Radiator CU Material of Plastic TPEE / ABS Cable Type RG178 Connector Type SMA Male Reverse C.Environmental Operation Temperature -40 ̊C ~ + 70 ̊C Storage Temperature -40 ̊C ~ + 80 ̊C 2 Product Number: ARS-NT5B7 Product Name: WIFI 7 Antenna 3 Characteristics and Reliability Test Test Items Test Condition and Procedure Requirements C1 S.W.R. Set DUT on Network Analyzer; make individual calibration to test Directive DUT specification C2 Antenna Gain Set DUT on Antenna Chamber; make individual calibration to test Directive DUT specification M1 Vibration GB / T2423 . 48-1997 Amplitude: 0.03 inch (1.5mm); Freq: 20 to 80 to 20 Hz 3 directions; 2 hours for each direction 1.No Visual Damage 2.Frequency Tol.<= 5% M2 Random Drop GB / T2423.8-1995 Height: 1.0 Meter; 3 directions; 1 time for each direction 1.No parts separated 2.Frequency Tol.<= 5% M3 Solderability GB 2423 . 28- 82 Solder iron: 260±5°C; Duration: 5 seconds 1.Mounted on PCB 2.No Visual Damage M4 Terminal- Pull Test Holding with individual specification; force applied to axis of terminal 1.Directive DUT specification 2.Frequency Tol.<= 5% M5 Terminal- Torque Test Holding with individual specification; applied clockwise and counterclockwise to the axis of terminal 1.Directive DUT specification 2.Frequency Tol.<= 5% M6 Dimension Inspection of dimension, color, material, package, surface process Directive DUT specification E1 Salt Spray GB / T 2423 . 17- 93 Temp: 35°C; RH: >= 95%; NaCl solution: >= 5%; Time: 24 hours After 2 Hours Recovery 1.No Visual Damage 2.Frequency Tol.<= 5% E2 Humidity GB / T 2423 . 4 - 93 Temp: 80°C / 12 H; -40°C / 12H RH: >= 90%; Time: 24 hours After 2 Hours Recovery 1.No Visual Damage 2.Frequency Tol.<= 5% E3 Thermal Shock GB / T 2423 . 22 - 87 1 Cycle: - 40°C (30 minutes) to + 80°C (30 minutes) Cycles: 24 After 2 Hours Recovery 1.No Visual Damage 2.Frequency Tol.<= 5% E4 Life (High Temp.) GB /T 2423 . 2 - 89 Temp: 80°C; Time: 24 hours After 2 Hours Recovery 1.No Visual Damage 2.Frequency Tol.<= 5% R1 RoHS With Reference to IEC 62321:2008 with flow chart Directive RoHS 2015/863/EU 3 Product Number:ARS-NT5B7 Product Name: WIFI 7 Antenna 4 Antenna - S Parameter Test Data 4 Product Number:ARS-NT5B7 Product Name: WIFI 7 Antenna 5 Antenna - Radiation Pattern Test Data 2400 MHz 2450 MHz 2500 MHz 5150 MHz 5600 MHz 5850 MHz 5 Product Number:ARS-NT5B7 Product Name: WIFI 7 Antenna 5925 MHz 6525 MHz 7125 MHz 6

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.0(2024/11/01) Page 1 of 85 TR-4-E-R027 TEST REPORT Applicant Name: Iconnect Address: No.9, Aly. 58, Ln. 112, Ruiguang Rd., Neihu Dist.,Taipei City, Taiwan Report Number: 2604Q36815E-RF-00A FCC ID: 2AB879886 Test Standard (s) FCC PART 15.407 Sample Description Product Name: WiFi Module Model No.: AWMC9886PH Trade Mark: ALFA Date Received: 2026-02-26 Report Date: 2026-05-14 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2604Q36815E-RF-00A Rev:A/4.0(2024/11/01) Page 2 of 85 TR-4-E-R027 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 4 GENERAL INFORMATION ............................................................................................................................ 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 5 OBJECTIVE ................................................................................................................................................... 6 TEST METHODOLOGY .................................................................................................................................... 6 TEST FACILITY .............................................................................................................................................. 6 MEASUREMENT UNCERTAINTY ....................................................................................................................... 6 SYSTEM TEST CONFIGURATION ............................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................... 7 EUT EXERCISE SOFTWARE AND POWER LEVEL # ............................................................................................ 7 SPECIAL ACCESSORIES ................................................................................................................................. 7 EQUIPMENT MODIFICATIONS .......................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................... 8 EXTERNAL I/O CABLE .................................................................................................................................... 8 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 8 SUMMARY OF TEST RESULTS ................................................................................................................. 10 TEST EQUIPMENT LIST ............................................................................................................................. 11 ANTENNA REQUIREMENT ........................................................................................................................ 13 APPLICABLE STANDARD ............................................................................................................................... 13 ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................... 13 AC CONDUCTED EMISSIONS ................................................................................................................... 14 APPLICABLE STANDARD ............................................................................................................................... 14 EUT SETUP ................................................................................................................................................ 14 EMI TEST RECEIVER SETUP ........................................................................................................................ 14 TEST PROCEDURE ...................................................................................................................................... 14 CALCULATION ............................................................................................................................................. 15 UNDESIRABLE EMISSION .........…

Text truncated - open the document above for the full version.