2ABBA-SENSORWireless parking space occupancy sensor

Frogparking Site Hardware Installation Instructions Frogparking Limited 36 Victoria Avenue Palmerston North www.frogparking.com Frogparking Limited – Proprietary and Confidential July 2013 2 FROGPARKING SITE HARDWARE INSTALLATION INSTRUCTIONS This document is for authorized Frogparking installers only. The instructions detailed below are for installing the following Frogparking hardware: 1. Wireless Link (a Frogparking gateway) 2. Surface mount Frog sensors Each piece of hardware is covered in detail in a dedicated section. Review the tools required and then visit the appropriate hardware section for further instructions. Tools required The following tools will be required to successfully install your Frogparking hardware. General  Samsung Galaxy S3 or S4 with data services and the latest installer app. loaded (contact Frogparking for the app).  Laptop (if checking system status on site). Requires WIFI or data services but could be tethered to smartphone for web access. Wireless Link Installation  SIM card with data services and details of required settings for the data service.  No1. Philips screwdriver  No2. Philips screwdriver  ‘Band-it’ strapping, buckles and strapping tensioning tool (http://www.band-it- idex.com/en/products/Tools/BAND-IT%20Tool.html) Note that the Band-it strapping hardware to fix the wireless link bracket to a pole is listed here as it is not included as part of the Wireless Link and is up to the installer to supply.  Tin snips  Pliers  Hammer  Ladder or alternative to reach installation height safely. Frog Installation Frogparking Limited – Proprietary and Confidential July 2013 3  Cordless Hammer drill with 2 batteries (Recommended by Frog: Ramset R28 Lithium Ion)  5mm masonry drill bits (standard, approximately 1 per 100 frogs with space markers)  6mm masonry drill bits (for concrete and paving stones only, alternatively use 5mm masonry bit and 30mm masonry screws)  Brush  Cordless power drill with 2 batteries (18V minimum, recommended by Frog: Hitachi 18V Lithium Ion)  On site power for charging batteries e.g. generator. Ensure enough hot points for all chargers/devices!  T30 Torx driver bits  Drilling jig With all the required tools ready to go, you can now begin installation. Frogparking Limited – Proprietary and Confidential July 2013 4 1. Wireless Link Installation The Wireless Link is an essential part of the Frogparking system, providing the bridge between the sensors and the web based management system. Installing a Wireless Link involves several key steps: 1. Fit the SIM Card 2. Register the Wireless Link on the Frogparking system 3. Mount the Wireless Link Instructions for each step are given below. Fitting the SIM Card If you are supplying your own SIM card for the Wireless Link data services, this will need to be fitted. Follow the below steps to fit the SIM card... Remove the mounting bracket If the Wireless Link was shipped with its mounting bracket attached, use a No.2 Philips screwdriver to remove the 4 screws holding the bracket in place. Remove the bracket taking care not to damage the antenna (if fitted). If the antenna is not fitted – fit it now. Remove the circuit board and battery sub assembly Using a No.1 Philips screwdriver, remove the 2 screws holding the sub assembly in place. 1 2 Frogparking Limited – Proprietary and Confidential July 2013 5 Carefully slide out the sub assembly taking care not to damage the circuit board. Insert the SIM card The SIM card holder is located near the end of the board on the side facing in towards the battery. Insert the SIM card so that the contacts are facing down and the chamfer on the corner of the card is to the outside of the board. It is a good idea to check the operation of the Wireless Link with the SIM card prior to mounting the Wireless Link, as once mounted it will be more difficult to reach and the LED’s are not visible. See the later section on Registering the Wireless Link for further details. Registering the Wireless Link To register a Wireless Link on the Frogparking system, the Frogparking installer app. is required on a Galaxy Samsung S3 or S4. Follow the below steps to register, setup and activate the Wireless Link. These steps presume the SIM card has already been fitted and the Wireless Link is ready for operation. If the Wireless Link’s antenna has not yet been fitted, fit the antenna now. 3 Frogparking Limited – Proprietary and Confidential July 2013 6 Start the Frogparking Installer app, log in and navigate to the install gateway screen Scan the gateway... 1 2 scan here Frogparking Limited – Proprietary and Confidential July 2013 7 Enter the settings... The appropriate APN to access the SIM cards data services An ID number to identify the SIM card, typically the number printed on the SIM card. The user name for the data services (if any) The password for the data services (if any) If it is desirable for the gateway to have custom operational hours outside of the default settings for the organization, un-tick the ‘Default Times’ box and use the ‘Set Wake Up Time’ and ‘Set Sleep Time’ buttons to define the appropriate times. Set the Gateway Location Next, press the ‘Set Gateway Location’ button to go to the map screen for locating the gateway in the system. A blue dot will show your current location. Scroll the map until the white cross is positioned where the gateway is located and then activate the menu and press ‘Set Gateway Location’. A green dot will now show the marked position. The ‘My Location’ button will centre the map on the current GPS position. ‘Gateway Location’ will centre the map on the existing gateway location if one has previously been entered. ‘Change Map Mode’ will toggle on and off the satellite images displayed on the map. When done, press the back button to return to the previous screen to check details, or ‘Install Gateway’ to proceed with the installation without double checking details. 3 4 Frogparking Limited – Proprietary and Confidenti…

Text truncated - open the document above for the full version.

Frog Sensor and Wireless Link 915 MHz User Guide Frogparking Limited 36 Victoria Avenue Palmerston North www.frogparking.com 1. Introduction The Frog Sensor and Wireless Link are designed to operate without human interaction directly. Management of the system is via the web interface using an external computer, its browser and the internet. Connection to the Frog Parking management servers requires a login to ensure only valid users are able to access the information provided, and only Administrators of the system are able to manage system configuration. Because of this, the requirement for a user manual for the Frog Sensor and Wireless Link has not been found to be required. An installation guide has been completed, as this is the most common human interaction with the two units. 2. FCC Compliance Label Statements: The Installation Guide contains the following statements in lieu of them being included on the device labels. Frog Sensor and Wireless Link: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning: Changes or modifications not expressly approved by Frogparking Ltd could void the user’s authority to operate the equipment.

9 June 2014 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Permanent Confidentiality To whom it may concern: In accordance with 47CFR Section 0.457 and Section 0.459 pertaining to confidential material, we hereby request to hold permanently confidential all information contained within the below identified exhibits/document categories submitted pursuant to radio equipment certification requirements for FCC ID: 2ABBA-SENSOR 1. Block Diagram 2. Operational Description 3. Schematics 4. Parts List The above material contains trade secrets and proprietary information as specified by 47CFR 0.457(d) and technical data, which would customarily be guarded from competitors. The public disclosure of this information might be harmful to our company and provide unjustified benefits to our competitors. Sincerely, Don Sandbrook CEO Frogparking Ltd 36 Victoria Avenue Palmerston North 4410 New Zealand +64 6 359 0077

9 June 2014 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Permanent Confidentiality To whom it may concern: In accordance with 47CFR Section 0.457 and Section 0.459, FCC Public Notice DA04-1705 and KDB Publication 726920 pertaining to confidential material, we hereby request to hold temporarily confidential all information contained within the below identified exhibits/document categories submitted pursuant to radio equipment certification requirements for FCC ID: 2ABBA-SENSOR for 180 days (maximum 180 days). 1. External Photos 2. Internal Photos 3. Test Setup Photos 4. User Manual 5. Block Diagram 6. Operational Description 7. Schematics 8. Parts List The above material contains trade secrets and proprietary information as specified by 47CFR 0.457(d) and technical data, which would customarily be guarded from competitors. The public disclosure of this information might be harmful to our company and provide unjustified benefits to our competitors. Sincerely, Don Sandbrook CEO Frogparking Ltd 36 Victoria Avenue Palmerston North 4410 New Zealand +64 6 359 0077

Frog Sensor and Wireless Link 915 MHz External Photographs Frogparking Limited 36 Victoria Avenue Palmerston North www.frogparking.com 2. Frog Sensor External Photos

Frog Sensor Label and Location Frogparking Limited 36 Victoria Avenue Palmerston North www.frogparking.com FCC Compliance Label The Frog Sensor has the following label applied to the underside of the sensor. This is not visible once installed but is when the device is purchase from frogparking. The label is located as shown below.

Frog Sensor and Wireless Link 915 MHz Internal Photographs Frogparking Limited 36 Victoria Avenue Palmerston North www.frogparking.com 2. Frog Sensor Internal Photos The Frog Sensor consists of the following components. 1. Main Board (see photograph), 2. Battery, 3. IR Dome, 4. ‘O’ Ring Seal, 5. IR Insert Tab, 6. Enclosure Base, 7. Sealing Tape (3M), 8. Assembly Screws (x3), 9. Enclosure Shroud (Maybe either yellow or black), and 10. Installation Screws (x3). All these components can be seen in the following photograph. Figure 6 - Frog Sensor Components Battery Main Board IR Dome IR Insert Tab ‘O’ Ring Seal Battery Enclosure Shroud Installation Screws Enclosure Base Assembly Screws Sealing Tape (3M) Figure 7 - Frog Main Board (Component side). Figure 8 - Frog Main Board (Top side). Figure 9 - Frog Main Board and IR Insert Tab inserted, Battery and Tape Seal fitted Figure 10 - IR Dome, ‘O’ Ring Seal and Circuit Board installed in Enclosure Base

____________________________________________________________________________________________________________________________________________________________________________ Page 17 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. Section 15.247(i) – Radio Frequency Hazard Information As per Section 15.247 (i) Spread spectrum transmitters operating in the 902 – 928 MHz band are required to be operated in a manner that ensures that the public is not exposed to RF energy levels in accordance with CFR 47, Section 1.1307(b)(1). In accordance with this section, and also Section 2.1091, this device has been defined as a mobile device whereby a distance of 20 cm or greater can normally be maintained between the user and the device. This transmitter would normally mounted at road level underneath parked vehicles. In accordance with Section 1.1310 the Maximum Permissible Exposure (MPE) limits for the General Population / Uncontrolled Exposure of f/1500 have been applied. The maximum distance from the antenna at which the MPE is met or exceeded is calculated from the equation relating field strength in V/m, transmit power in watts, transmit antenna gain and separation distance in metres: E, V/m = (! (30 * P * G)) / d Power density, mW/cm 2 = E 2 /3770 E for MPE: (921/1500) = E 2 /3770 E = !(921/1500)*3770 E = 48.1 V/m The maximum radiated power measured was +20.5 dBm or 0.1122 Watts Therefore: E = ! (30 * P * G) / d d = ! (30 * P * G) / E d = ! (30 * 0.1122) / 48.1 d = 0.038 m or 3.8 cm In order to meet the MPE requirements a minimum safe distance of at least 20 cm will be required. Result: Complies.

____________________________________________________________________________________________________________________________________________________________________________ Page 1 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. EMC Technologies (NZ) Ltd PO Box 68-307, Newton Auckland 1145 New Zealand Phone 09 360 0862 Fax 09 360 0861 E-Mail Address: [email protected] Web Site: www.emctech.com.au TEST REPORT Frogparking V1.0 Battery Frog tested to 47 Code of Federal Regulations Part 15 - Radio Frequency Devices Subpart C – Intentional Radiators Section 15.247 - Operation in the band 902 – 928 MHz for Frogparking Ltd This Test Report is issued with the authority of: ______________________________ Andrew Cutler - General Manager ____________________________________________________________________________________________________________________________________________________________________________ Page 2 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. Table of Contents 1. STATEMENT OF COMPLIANCE 3 2. RESULTS SUMMARY 3 3. INTRODUCTION 4 4. CLIENT INFORMATION 4 5. DESCRIPTION OF TEST SYSTEM 4 6. RESULTS 6 7. TEST EQUIPMENT USED 18 8. ACCREDITATIONS 18 9. PHOTOGRAPHS 19 ____________________________________________________________________________________________________________________________________________________________________________ Page 3 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. 1. STATEMENT OF COMPLIANCE The Frogparking V1.0 Battery Frog complies with FCC Part 15 Subpart C Section 15.247 as an Intentional Radiator when the methods as described in ANSI C63.4 - 2003 are applied along with the methods defined in FCC Public Notice DA 00-705. 2. RESULTS SUMMARY The results of testing carried out between October 1 st and September 7 th 2013 and on the 15 th January 2014 are detailed below: Clause Parameter Result 15.201 Equipment authorisation requirement Certification required. 15.203 Antenna requirement Complies. This device uses an internal antenna. 15.204 External PA and antenna modifications Noted. 15.205 Restricted bands of operation Complies. 15.207 Conducted limits Not applicable. Device cannot be directly or indirectly powered from the Public AC mains supply. 15.209 Radiated emission limits Noted. See 15.247 requirements. 15.247 (a)(1) Hopping channel separation Complies (a)(1)(i)(iii) Channel occupancy / Bandwidth Complies (b)(1)(2) Peak output power Complies (b)(4) Antenna gain less than 6 dBi Complies (d) Out of band emissions Complies (g) Use of all channels Not applicable (h) Intelligent frequency hopping Not applicable (i) Radio frequency hazards Complies ____________________________________________________________________________________________________________________________________________________________________________ Page 4 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. 3. INTRODUCTION This report describes the tests and measurements performed for the purpose of determining compliance with the specification. The client selected the test sample. This report relates only to the sample tested. This report contains no corrections or erasures. Measurement uncertainties with statistical confidence intervals of 95% are shown below test results. Both Class A and Class B uncertainties have been accounted for, as well as influence uncertainties where appropriate. 4. CLIENT INFORMATION Company Name Frogparking Ltd Address 36 Victoria Avenue City Palmerston North 4410 Country New Zealand Contact Mr Kahu Swanson 5. DESCRIPTION OF TEST SYSTEM Brand Name Frogparking Model Number V1.0 Product Battery Frog Manufacturer Gallagher Group Ltd Country of Origin New Zealand Serial Number Sample not serialized FCC ID Not yet determined ____________________________________________________________________________________________________________________________________________________________________________ Page 5 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. Product Description The system tested is a parking space management system that consists of a Parking Space Sensor, which is a sealed road mounted sensor, and a Wireless Link, which collects the data transmitted by the parking space sensors and forwards it to a distant web served. The Parking Space Sensor and the Wireless Link communication using low power frequency hopping spread spectrum transceivers operating in the 900 MHz band. The Wireless Link transceiver communicates with the web server using a cellular modem. Band of Operation: 902 – 928 MHz Modulation: Frequency hopping spread spectrum – GFSK Channels used: 50 Channels available: 64 Operating frequencies: 921.870 – 927.540 MHz Channel spacing: 90 kHz Rated Conducted Power: +20 dBm (100 mW) Data Rate: 38,400 bps Modulation Description: 2 level GFSK Modulation Designator: F7D Antenna Type: Splatch ANT-916-SP quarter wave internal antenna with a maximum gain of approximately 1.3 dBi Power Supply: Internal Li-Ion battery pack External Ports: Device has no external ports RF Module Si4432 radio IC Frequencies in use: 32.768 kHz, 24.5 MHz and 30 MHz ____________________________________________________________________________________________________________________________________________________________________________ Page 6 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. 6. RESULTS Standard The sample was tested in accordance with 47 CFR Part 15 Subpart C and in particular section 15.247 Methods and Procedures The following measurement methods and procedures have been applied: - ANSI C63.4 – 2003 - FCC Public Notice DA 00-0705 Section 15.201: Equipment authorisation requirement Certification as detailed in Subpart J of Part 2 is required for this device. Section 15.203: A…

Text truncated - open the document above for the full version.

____________________________________________________________________________________________________________________________________________________________________________ Page 22 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. Radiated Emission Test Set Up ____________________________________________________________________________________________________________________________________________________________________________ Page 23 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. ____________________________________________________________________________________________________________________________________________________________________________ Page 24 of 24 Test Report No 130908.3 17 th January 2014 This report may not be reproduced except in full. Radiated emissions test set up photos – Below 30 MHz Radiated emissions test set up photos – Above 30 MHz